User guide
Table Of Contents
- Contents
- Introduction
- The basics
- Entering your settings
- Basic steps
- Setting the time and date
- Selecting the language
- Setting your Alarm/Alert Type
- Entering your glucose monitoring settings
- Turning on the sensor
- Selecting the BG units
- Turning on the Glucose Alerts
- Setting the Glucose Limits
- Setting the Glucose Limits start time
- Setting the High Snooze
- Setting the Low Snooze
- Setting the Predictive glucose alert
- Setting the Rate Alerts
- AUC calculation
- Setting the Alarm Snooze
- Setting the Cal Reminder
- Entering the transmitter identification number
- Setting up the Missed Data option
- Setting the sensor glucose graph timeout
- Reviewing your settings
- Setting up your transmitter and sensor
- Meter option
- Using your system
- Utilities
- Therapy management software
- Troubleshooting and alarms/alerts
- About alarms and alerts
- What to do when you get an alarm/alert
- Sensor alerts
- Viewing your sensor alert history
- System alarms
- Viewing your system alarm history
- Understanding your transmitter, tester, and charger
- Troubleshooting the transmitter
- Troubleshooting the monitor
- My monitor will not display my BG measurement from my meter
- Reconnect old sensor
- Find lost sensor
- What happens if I leave the monitor battery out for more than ten minutes?
- Why doesn't my monitor battery last very long?
- What is a CHECK SETTINGS alarm?
- My screen looks distorted
- I dropped my monitor
- I submerged my monitor in water
- I cannot get to the User Settings screen
- System maintenance
- System specifications
- Alarm/alert types
- Alarm/alert messages and codes
- Alarm/alert history
- Backlight
- Screen and menu timeout
- Sensor glucose graph timeout
- High and low Glucose Limits (CSS7100)
- High and low Glucose Limits (CSS7100K)
- Daily totals
- Default screen
- Default settings
- ENTER BG meter values
- Meter ID entries
- Power supply
- System safety checks
- Radio frequency (RF) communication specifications
- Quality of service
- Data security
- Monitor size
- Monitor weight
- TIME/DATE SET screen
- STATUS screen
- Guidance and manufacturer's declaration
- MiniLink specifications
- Warranty
- Icon table
- Sensor accuracy
- Performance results in adults
- Accuracy of Guardian RT readings
- Precision of Guardian RT readings
- Low and High Alerts in adults
- Guardian RT Sensor Performance and Calibration Stability As a Function of Time
- Effects of calibration frequency
- Performance results in children and adolescents
- Low and High alerts in children and adolescents
- Glossary
- Index
For multiple-patient use
When using the transmitter in a healthcare facility, always clean and disinfect the transmitter after each
use.
Warning: You must adhere to Standard Precautions when handling or using this device. All part of the
system should be considered potentially infectious and are capable of transmitting blood-borne
pathogens between patients and healthcare professionals. For more information, refer to Guideline
for Isolation Precautions: Preventing Transmission of Infectious Agents in Healthcare Settings 2007,
http://www.cdc.gov/hicpac/2007ip/2007isolationprecautions.html.
The transmitter must be disinfected after use on each patient. This system may only be used for
testing multiple patients when Standard Precautions and Medtronic's disinfection procedures are
followed.
To clean and disinfect the transmitter, you will need the following materials: gloves, ENZOL
®
Enzymatic
Detergent, a soft-bristled toddler toothbrush, Clorox
®
Regular-Bleach, 70% isopropyl alcohol, two
containers, and a few clean, dry cloths. You can order these supplies from http://www.amazon.com/.
Use life
The MiniLink transmitter can be used 122 times or a year, whichever comes first. Discard the transmitter
at this point. If you continue to use the transmitter beyond 122 times or a year, the cleaning and
disinfection process may damage the device. Contact Medtronic to order a new transmitter. The
transmitter was validated to last 122 cycles, which represents one cleaning and disinfection cycle every
three days for one year.
To clean and disinfect the transmitter:
1 Wash your hands and put on gloves.
2 Inspect the inside of the transmitter's connector opening for any sign of body fluid. For instructions on
how to inspect the connector pins, see Inspecting the transmitter connector pins, on page 102.
Caution: The person inspecting the transmitter must have sufficient vision that enables him or
her to see small drops of body fluid or debris.
System maintenance106