User guide
Table Of Contents
- Contents
- Introduction
- The basics
- Entering your settings
- Basic steps
- Setting the time and date
- Selecting the language
- Setting your Alarm/Alert Type
- Entering your glucose monitoring settings
- Turning on the sensor
- Selecting the BG units
- Turning on the Glucose Alerts
- Setting the Glucose Limits
- Setting the Glucose Limits start time
- Setting the High Snooze
- Setting the Low Snooze
- Setting the Predictive glucose alert
- Setting the Rate Alerts
- AUC calculation
- Setting the Alarm Snooze
- Setting the Cal Reminder
- Entering the transmitter identification number
- Setting up the Missed Data option
- Setting the sensor glucose graph timeout
- Reviewing your settings
- Setting up your transmitter and sensor
- Meter option
- Using your system
- Utilities
- Therapy management software
- Troubleshooting and alarms/alerts
- About alarms and alerts
- What to do when you get an alarm/alert
- Sensor alerts
- Viewing your sensor alert history
- System alarms
- Viewing your system alarm history
- Understanding your transmitter, tester, and charger
- Troubleshooting the transmitter
- Troubleshooting the monitor
- My monitor will not display my BG measurement from my meter
- Reconnect old sensor
- Find lost sensor
- What happens if I leave the monitor battery out for more than ten minutes?
- Why doesn't my monitor battery last very long?
- What is a CHECK SETTINGS alarm?
- My screen looks distorted
- I dropped my monitor
- I submerged my monitor in water
- I cannot get to the User Settings screen
- System maintenance
- System specifications
- Alarm/alert types
- Alarm/alert messages and codes
- Alarm/alert history
- Backlight
- Screen and menu timeout
- Sensor glucose graph timeout
- High and low Glucose Limits (CSS7100)
- High and low Glucose Limits (CSS7100K)
- Daily totals
- Default screen
- Default settings
- ENTER BG meter values
- Meter ID entries
- Power supply
- System safety checks
- Radio frequency (RF) communication specifications
- Quality of service
- Data security
- Monitor size
- Monitor weight
- TIME/DATE SET screen
- STATUS screen
- Guidance and manufacturer's declaration
- MiniLink specifications
- Warranty
- Icon table
- Sensor accuracy
- Performance results in adults
- Accuracy of Guardian RT readings
- Precision of Guardian RT readings
- Low and High Alerts in adults
- Guardian RT Sensor Performance and Calibration Stability As a Function of Time
- Effects of calibration frequency
- Performance results in children and adolescents
- Low and High alerts in children and adolescents
- Glossary
- Index
18 Inspect the housing of the transmitter for any signs of cracking, flaking, or damage. If you see any of
these signs, you must now discard the disinfected transmitter according to local regulations for
battery disposal (non-incineration).
Warning: Cracking, flaking, or damage of the housing are signs of deterioration and the
performance of the device may be compromised. This may affect the ability to properly clean
and disinfect the transmitter. If these signs are noted, stop using the device and call the
Medtronic Diabetes 24 Hour HelpLine. The device must be discarded according to local
regulations for battery disposal (non-incineration).
19 Discard the used gloves and thoroughly wash hands with soap and water.
Removing adhesive residue
You may need to perform this procedure only if you have used optional occlusive dressing, which may
leave adhesive residue on the transmitter. If you visually inspect the transmitter and see adhesive residue
on it, follow the instructions below.
To remove adhesive residue, you will need the following materials: Detachol
®
medical adhesive remover
and cotton swabs. You can buy Detachol at http://www.amazon.com/.
To remove adhesive residue:
1 Make sure the tester is attached to the transmitter.
2 Holding the tester, saturate a cotton swab in the Detachol solution and gently rub the adhesive
residue on the transmitter until it is fully removed.
3 Continue with the appropriate single-patient or multi-patient cleaning procedure above.
System maintenance110