User guide
Table Of Contents
- Contents
- Introduction
- The basics
- Entering your settings
- Basic steps
- Setting the time and date
- Selecting the language
- Setting your Alarm/Alert Type
- Entering your glucose monitoring settings
- Turning on the sensor
- Selecting the BG units
- Turning on the Glucose Alerts
- Setting the Glucose Limits
- Setting the Glucose Limits start time
- Setting the High Snooze
- Setting the Low Snooze
- Setting the Predictive glucose alert
- Setting the Rate Alerts
- AUC calculation
- Setting the Alarm Snooze
- Setting the Cal Reminder
- Entering the transmitter identification number
- Setting up the Missed Data option
- Setting the sensor glucose graph timeout
- Reviewing your settings
- Setting up your transmitter and sensor
- Meter option
- Using your system
- Utilities
- Therapy management software
- Troubleshooting and alarms/alerts
- About alarms and alerts
- What to do when you get an alarm/alert
- Sensor alerts
- Viewing your sensor alert history
- System alarms
- Viewing your system alarm history
- Understanding your transmitter, tester, and charger
- Troubleshooting the transmitter
- Troubleshooting the monitor
- My monitor will not display my BG measurement from my meter
- Reconnect old sensor
- Find lost sensor
- What happens if I leave the monitor battery out for more than ten minutes?
- Why doesn't my monitor battery last very long?
- What is a CHECK SETTINGS alarm?
- My screen looks distorted
- I dropped my monitor
- I submerged my monitor in water
- I cannot get to the User Settings screen
- System maintenance
- System specifications
- Alarm/alert types
- Alarm/alert messages and codes
- Alarm/alert history
- Backlight
- Screen and menu timeout
- Sensor glucose graph timeout
- High and low Glucose Limits (CSS7100)
- High and low Glucose Limits (CSS7100K)
- Daily totals
- Default screen
- Default settings
- ENTER BG meter values
- Meter ID entries
- Power supply
- System safety checks
- Radio frequency (RF) communication specifications
- Quality of service
- Data security
- Monitor size
- Monitor weight
- TIME/DATE SET screen
- STATUS screen
- Guidance and manufacturer's declaration
- MiniLink specifications
- Warranty
- Icon table
- Sensor accuracy
- Performance results in adults
- Accuracy of Guardian RT readings
- Precision of Guardian RT readings
- Low and High Alerts in adults
- Guardian RT Sensor Performance and Calibration Stability As a Function of Time
- Effects of calibration frequency
- Performance results in children and adolescents
- Low and High alerts in children and adolescents
- Glossary
- Index
How to check for rapid changes in sensor glucose
If your sensor glucose (SG) rises or falls faster than a certain rate, Rapid Change arrows automatically
appear in the graphs next to the SG number, as shown in this section. You can also set your Rate of
Change alerts to tell you when these arrows appear on your SG graphs.
The rapid change arrows
These examples show how the Rapid Change arrows tell you when your SG rises or falls faster than a
certain per-minute rate. The arrow direction shows if your SG measurements are rising or falling. The
number of arrows (one or two) shows how rapidly your SG is changing.
•
One up arrow
shows that your SG has been rising at a rate of
1.0 to 2.0 mg/dL (0.06 and 0.11 mmol/L) per minute.
239
15:16
Hour
•
One down arrow
shows that your SG has been falling at a
rate of 1.0 to 2.0 mg/dL (0.06 and 0.11 mmol/L) per minute.
131
15:16
Hour
•
Two up arrows
show that your SG has been rising at a rate
of 2.0 mg/dL (0.11 mmol/L) or more per minute.
142
Hour
•
Two down arrows
show that your SG has been falling at a
rate of 2.0 mg/dL (0.11 mmol/L) or more per minute.
112
Hour
Using your system 61
Chapter 6