User guide
Table Of Contents
- Contents
- Introduction
- The basics
- Entering your settings
- Basic steps
- Setting the time and date
- Selecting the language
- Setting your Alarm/Alert Type
- Entering your glucose monitoring settings
- Turning on the sensor
- Selecting the BG units
- Turning on the Glucose Alerts
- Setting the Glucose Limits
- Setting the Glucose Limits start time
- Setting the High Snooze
- Setting the Low Snooze
- Setting the Predictive glucose alert
- Setting the Rate Alerts
- AUC calculation
- Setting the Alarm Snooze
- Setting the Cal Reminder
- Entering the transmitter identification number
- Setting up the Missed Data option
- Setting the sensor glucose graph timeout
- Reviewing your settings
- Setting up your transmitter and sensor
- Meter option
- Using your system
- Utilities
- Therapy management software
- Troubleshooting and alarms/alerts
- About alarms and alerts
- What to do when you get an alarm/alert
- Sensor alerts
- Viewing your sensor alert history
- System alarms
- Viewing your system alarm history
- Understanding your transmitter, tester, and charger
- Troubleshooting the transmitter
- Troubleshooting the monitor
- My monitor will not display my BG measurement from my meter
- Reconnect old sensor
- Find lost sensor
- What happens if I leave the monitor battery out for more than ten minutes?
- Why doesn't my monitor battery last very long?
- What is a CHECK SETTINGS alarm?
- My screen looks distorted
- I dropped my monitor
- I submerged my monitor in water
- I cannot get to the User Settings screen
- System maintenance
- System specifications
- Alarm/alert types
- Alarm/alert messages and codes
- Alarm/alert history
- Backlight
- Screen and menu timeout
- Sensor glucose graph timeout
- High and low Glucose Limits (CSS7100)
- High and low Glucose Limits (CSS7100K)
- Daily totals
- Default screen
- Default settings
- ENTER BG meter values
- Meter ID entries
- Power supply
- System safety checks
- Radio frequency (RF) communication specifications
- Quality of service
- Data security
- Monitor size
- Monitor weight
- TIME/DATE SET screen
- STATUS screen
- Guidance and manufacturer's declaration
- MiniLink specifications
- Warranty
- Icon table
- Sensor accuracy
- Performance results in adults
- Accuracy of Guardian RT readings
- Precision of Guardian RT readings
- Low and High Alerts in adults
- Guardian RT Sensor Performance and Calibration Stability As a Function of Time
- Effects of calibration frequency
- Performance results in children and adolescents
- Low and High alerts in children and adolescents
- Glossary
- Index
Sensor glucose information
The following table lists the different types of SG information that the system automatically records. The
SG information is calculated by using all of the SG measurements that were received by the monitor during
the day.
Item Description
SG Average The average sensor glucose measurement.
Above Hi Limit The percentage of sensor glucose measurements that were above your High Glucose
Limit.
Within Limits The percentage of sensor glucose measurements that were between your Low
Glucose Limit and your High Glucose Limit.
Below Low Limit The percentage of sensor glucose measurements that were below your Low Glucose
Limit.
SG Std. Dev. The standard deviation of the sensor glucose measurements.
AUC Hi/Lo. The High and Low AUC reference values. This is a reference value that provides a
relative indication of the overall extent and duration of the glucose excursions on a
given day. These numbers are shown in mmol/L or mg/dL, depending on your BG
Unit setting.
#Hi/Lo Alarm The total number of glucose alerts. The number to the left is the total number of
high glucose alerts. The number to the right is the total number of low glucose
alerts.
Meter blood glucose information
The table below lists the different types of meter BG information that the system automatically records.
The meter BG information is calculated by using all of the automatic and manual meter BG measurements
received by the monitor, including measurements that were manually entered into the monitor. You may
view the data for a single day, or for a selected number of days.
An asterisk (*) next to a date means that the data for that day will not be used for the calculations that
are displayed in the Daily Average option. Anything, such as a time or date change, that shortens a day at
least one hour and twelve minutes (01:12) will cause the asterisk to display.
Utilities70