User guide
Table Of Contents
- Contents
- Introduction
- The basics
- Entering your settings
- Basic steps
- Setting the time and date
- Selecting the language
- Setting your Alarm/Alert Type
- Entering your glucose monitoring settings
- Turning on the sensor
- Selecting the BG units
- Turning on the Glucose Alerts
- Setting the Glucose Limits
- Setting the Glucose Limits start time
- Setting the High Snooze
- Setting the Low Snooze
- Setting the Predictive glucose alert
- Setting the Rate Alerts
- AUC calculation
- Setting the Alarm Snooze
- Setting the Cal Reminder
- Entering the transmitter identification number
- Setting up the Missed Data option
- Setting the sensor glucose graph timeout
- Reviewing your settings
- Setting up your transmitter and sensor
- Meter option
- Using your system
- Utilities
- Therapy management software
- Troubleshooting and alarms/alerts
- About alarms and alerts
- What to do when you get an alarm/alert
- Sensor alerts
- Viewing your sensor alert history
- System alarms
- Viewing your system alarm history
- Understanding your transmitter, tester, and charger
- Troubleshooting the transmitter
- Troubleshooting the monitor
- My monitor will not display my BG measurement from my meter
- Reconnect old sensor
- Find lost sensor
- What happens if I leave the monitor battery out for more than ten minutes?
- Why doesn't my monitor battery last very long?
- What is a CHECK SETTINGS alarm?
- My screen looks distorted
- I dropped my monitor
- I submerged my monitor in water
- I cannot get to the User Settings screen
- System maintenance
- System specifications
- Alarm/alert types
- Alarm/alert messages and codes
- Alarm/alert history
- Backlight
- Screen and menu timeout
- Sensor glucose graph timeout
- High and low Glucose Limits (CSS7100)
- High and low Glucose Limits (CSS7100K)
- Daily totals
- Default screen
- Default settings
- ENTER BG meter values
- Meter ID entries
- Power supply
- System safety checks
- Radio frequency (RF) communication specifications
- Quality of service
- Data security
- Monitor size
- Monitor weight
- TIME/DATE SET screen
- STATUS screen
- Guidance and manufacturer's declaration
- MiniLink specifications
- Warranty
- Icon table
- Sensor accuracy
- Performance results in adults
- Accuracy of Guardian RT readings
- Precision of Guardian RT readings
- Low and High Alerts in adults
- Guardian RT Sensor Performance and Calibration Stability As a Function of Time
- Effects of calibration frequency
- Performance results in children and adolescents
- Low and High alerts in children and adolescents
- Glossary
- Index
3 Press ACT. The system automatically runs the Selftest in the following order:
a. Screen Test:
The screen appears all black.
b. Selftest:
The monitor counts down from 10 (it skips the number 4).
c. Tone Test:
You should hear beeps.
d. Vibrate Test:
You will feel vibrations.
4 After Selftest is finished, TEST COMPLETE shows on the screen. The screen returns to the UTILITIES
MENU, then to the HOME screen.
User settings
This feature allows you to save your current settings, restore previously saved settings, and clear your
current settings. You can also check the history of your use of this feature, to include: the date and time
that you used the feature; and if you saved, restored, or cleared the settings.
The Save Settings feature lets you save a group of system settings. After the settings group is saved, you
can restore it at a later time as needed. When you restore a settings group, those settings become the
active, current settings. Using the Save Settings and Restore Settings features allows you to easily change
your current settings as needed without having to re-enter them.
When you clear your system settings, all your current settings are reset to the default settings (the
settings that came with your system). After you clear your current settings, do one of the following before
you can begin using your system:
• Restore previously saved settings using the Restore Settings feature
• Manually enter your settings into the monitor
Saving your settings
Use this procedure to save your current settings.
1 Open the UTILITIES MENU.
MAIN MENU > Utilities
2 Select User Settings. Hold down SHIFT and press ACT. The USER SETTINGS screen shows with Save
Settings selected.
Utilities76