Assembly Instruction

ManualsBrandsMercury Row ManualsCeiling LightsMayville 8 - Light Shaded Geometric Chandelier

1of2

(8)B10CandelabraBaseBulbs60WMaximum

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement

parts.

LightSource:

EstimatedAssemblyTime:

Preparation:

ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

Package Contents

Fixture Loop

6” Rod

Fixture Body

Hardware Contents

Crossbar

Lock Washer

Hex Nut

Nipple

Canopy

Chain Loop

Canopy Lock

Ring

Ceiling

Canopy

Quick Link

12” Rod with Nipple

STEP 1 Install Fixture Loop and Rods to Fixture Body-

A. Determine the Rods (B/C/D) to be assembled to the Fixture Body (F)

according to your hanging height.

B. Pass the supply wires and ground wire through the chosen rods

(B/C/D) and the Fixture Loop (A). Thread the Fixture Body (F), the

chosen Rods (B/C) and the Fixture Loop (A) together. Hand tighten

until snug.

Supply Wires and

Ground Wire

Figure 1

STEP 2 - Install the Crossbar to the junction box

A. Attach the Crossbar (AA) to the Outlet Box with the head of the

Green Ground Screw facing you. Secure it with Outlet Box Screws

(not included), tighten until snug.

Outlet Box

Outlet Box Screw

(not included)

Green Ground

Screw

Figure 2

STEP 3 Install the Canopy Chain Loop and Nipple-

A. Thread one Hex Nut (CC) to one end of the Nipple (DD) until it is at

least 0.25” from the end. Pass one Lock Washer (BB) over the end of

the Nipple (DD) and thread the Canopy Chain Loop (EE) onto the

Nipple (DD). By using pliers, thread the Hex Nut (CC) against the

Canopy Chain Loop (EE) and hand tighten until snug.

B. Thread another Hex Nut (CC) to the middle of the Nipple (DD). Place

another Lock Washer (BB) over the Nipple (DD) and then thread the

Nipple (DD) into the Crossbar (AA) until the Nipple (DD) is about

0.375” above the Crossbar (AA).

C. Remove the Canopy Lock Ring (FF) from the Canopy Chain Loop

(EE). Place the Ceiling Canopy (HH) over the Canopy Chain Loop

(EE) against the ceiling to determine the correct position of the

Nipple (DD). Thread the Canopy Lock Ring onto the Canopy Chain

Loop (EE). Adjust the Nipple (DD) to allow the Ceiling Canopy (HH)

to rest against the ceiling when held in place by the Canopy Lock

Ring (FF).

Suggested rods for Ceiling

height :

8’ ceiling : use (1) 6” rod and

(1) 12” rod

9’ ceiling : use (1) 6” rod and

(2) 12” rods

10’ ceiling : use (2) 6” rods

and (2) 12” rods

12” Rod

Glass

Shade

Assembly Instruction

Thank you for purchasing product.

Need assistance with parts or assembly? Call customer service

Summary of content (2 pages)

PAGE 1
Assembly Instruction Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (8) B10 Candelabra Base Bulbs 60W Maximum Estimated Assembly Time: 30-45 minutes Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture.
PAGE 2
(Step 5 Continued) (Step 3 Continued) D. Remove the Canopy Lock Ring (FF) and the Ceiling Canopy (HH). Tighten the Hex Nut (CC) against the Crossbar (AA) to secure in place. BB AA CC Note: If the electrical wire is going to be cut shorter than provided you will need to identify the "L" line wire and the "N" neutral wire before you cut the excess wire off. One is labeled N and the other labeled L. To do this separate the "L" line wire and the "N" neutral wire as far as you need to.