Specification

Specication
Industry Standards
The American Society for Testing and Materials (ASTM)
and the American National Standards Institute (ANSI) are
nationally recognized organizations, which identify and
develop industry test methods and technical standards.
All tile products distributed by Merola Tile are Grade 1,
First-Quality products and meet or exceed the
requirements of ANSI A137.1. Please refer to individual
product pages for item-specic technical data.
Static Coefcient of Friction (SCOF), ASTM C1028-06 /
Dynamic Coefcient of Friction (DCOF) AcuTest, ANSI
A137.1–2012, Section 9.6
The tile industry uses ASTM C1028-06 to measure the
coefcient of friction, or the relative slip resistance of
tile surfaces. This procedure measures the maximum
force required to initiate motion, or slip, across the tile
surface. The values are recorded and averaged to
determine the static COF. A newer standard, called DCOF,
is an evaluation of the COF of a tile surface under known
conditions using a standardized sensor prepared
according to a specic protocol. Measurements are made
using a tribometer, under wet conditions using a 0.05%
sodium lauryl sulfate solution to establish a thin lm
as would be present when a slip occurs. Because many
variables affect the risk of a slip occurring, the SCOF
and DCOF measurement shall not be the only factor in
determining the appropriateness of a tile for a particular
application.
Water Absorption, ASTM C373-88
Water absorption is measured using ASTM C373-88.
Individual tiles are weighed, saturated with water, and
weighed again. The percent difference between the two
values is the water absorption value. Tiles are categorized
according to water absorption percentages as follows:
Impervious Tiles absorbing 0.5% or less.
(Frostproof, can be used for outdoor applications)
Vitreous Tiles absorbing more than 0.5% but not more than 3.0%.
(Not frostproof, not recommended for outdoor applications)
Semi-Vitreous Tiles absorbing more than 3.0% but not more than 7.0%.
(Not frostproof, not recommended for outdoor applications)
Non-Vitreous Tiles absorbing more than 7.0%.
(Not frostproof, not recommended for outdoor applications)
Chemical Resistance, ASTM C650-04
Chemical resistance is measured using ASTM C650-04. A
tile sample is placed in continuous contact with a
selection of chemical agents for 24 hours, then the
surface is rinsed and examined for visible staining or
variation.
Break Strength, ASTM C648-04
Tiles used on oors and walls must be able to withstand
the expected load-bearing capacity of various
installations. The tile industry uses ASTM C648-04 to
determine the strength and durability of the tile. The test
method provides means for establishing whether or not a
tile meets the strength requirements which may appear
in tile specications. Tile strength is the force in pounds-
force (or newtons) necessary to cause an unsupported**
tile to break.
**Breaking strength does not measure the weight limit of
foot trafc or supported tile. The nal strength of a tile
installation is calculated by including (but not limited
to) the tile, the installation materials and method, and
suboor.
Merola Tile recommends adherence to industry
installation guidelines set forth here:
ANSI A108.1 - Installation of ceramic tile with Portland Cement
ANSI A108.4 - Installation of ceramic tile with water resistant organic adhesives
ANSI A108.5 - Installation of ceramic tile installed with dry-set Portland Cement
Mortar or Latex-Portland Cement Mortar
ANSI A108.6 - Installation for ceramic tile installed with chemical-resistant epoxy.
PEI Rating/Abrasion Resistance, ASTM C1027-99
The durability of glazed tile is measured by observing the
visible surface abrasion of the tile when subjected to the
ASTM C1027-99 testing procedure. Tiles are classied into
the following classes according to their durability:
PEI 0: (Wall Use Only) Not recommended for use on oors.
PEI 1: (Light Residential) Suitable for light-duty residential oors, bathrooms and
bedrooms without direct access from outside; no scratching dirt can be present (no
exterior access entrances)
PEI 2: (Residential) Suitable for all interior walls and light foot trafc such as
powder rooms and areas subject to soft-soled footwear or normal footwear trafc
with small amounts of scratching dirt (i.e. rooms in the living areas of homes
except kitchens, entrances and other areas that may be subjected to high foot
trafc).
PEI 3: (Heavy Residential or Light Commercial) Suitable for medium-duty
residential oors including kitchens, halls, corridors, balconies, terraces and areas
used more often with normal footwear and small amounts of dirt. Examples may
include residential kitchens and hallways with limited trafc from the outside.
PEI 4: (Commercial) Suitable for heavy-duty residential and commercial kitchens,
entrances, hotels, exhibition and sales rooms with some dirt conditions.
PEI 5: (Heavy Commercial) Suitable for both residential and high-trafc commercial
use, including extra heavy-duty oors and areas subject to heavy pedestrian trafc
over sustained periods with some dirt such as shopping centers, airport concourses,
public walkways and industrial applications.
Improving Homes. Improving Lives.