V20210257 CFN-1058 Instruction Manual Read Completely Before Installation & Use and Keep for Future Reference
TABLE OF CONTENTS Introduction ·························································································· 1 Package Contents ················································································· 2 Safety Information·················································································· 3 Preparation ·························································································· 4 Fan Housing Installation ······················································
PACKAGE CONTENTS b g c d a h e f i a. Fan Blades (×3) b. Ceiling Mounting Bracket j c. Canopy d. Canopy Cover e. Downrod f. Coupling Cover k g. Fan Housing h. Fan Motor Assembly i. Light Plate j. LED Light Kit k. Glass Shade l l. Remote Control m. Receiver n.
SAFETY INFORMATION Warning! 1. To reduce the risk of electric shock, ensure electricity has been turned off at the circuit breaker or fuse box before beginning. 2. All wiring must be in accordance with national and local electrical codes. Electrical installation should be performed by a qualified licensed electrician. 3. This fan is suitable for use with solid-state speed controls. 4.
PREPARATION 1. Turn Off Your Power Begin installation by removing fuses or turning off circuit breakers to the wiring you will be using. Use your compatible UL listed outlet box if you already have one installed. Failure to disconnect the power supply prior to installation may result in serious injury or death. 2. Choose Your Mounting Position If you need to install a new UL listed outlet box, secure it directly to your building's structure usingappropriate fasteners and materials.
FAN HOUSING INSTALLATION Reinforcing Plate Bolt Fan Housing Step 1. Remove the 8 pre-installed bolts from the reinforcing plate on the top of the motor assembly. Step 2. Fit the fan housing in place on the reinforcing plate and secure it by replacing and retightening the bolts.
INITIAL INSTALLATION Outlet Box Washers Ceiling Mounting Bracket Hook Mounting Screws/Bolts 120V Wires Step 1. Pass the 120V supply wires through the center hole in the ceiling mounting bracket. Step 2. Secure the ceiling mounting bracket to the outlet box with the provided mounting screws or bolts and spring or star washers. DOWNROD MOUNTING Step 1. Remove the hitch and lock pins. Loosen the pre-installed bolts on the top of the motor assembly.
CIRCUIT CONNECTIONS Again, ensure that the power has been cut before working with the wiring. Use the wire nuts provided with your fan. Registration Slot Ensure there are no loose wires or connections, and secure connectors with electrical tape. Step 1. Insert the receiver into the tray with the receiver facing the ceiling. For best performance, make sure the white antenna, on the end of the receiver, remains extended and not tangled with any of the electrical wires. Step 2.
CANOPY AND COVER INSTALLATION Outlet Box Ceiling Mounting Bracket Mounting Screws/Bolts Canopy Canopy Cover Step 1. Tuck all the connections neatly into the outlet box. Step 2. Slide the canopy up to the ceiling mounting bracket and place the key hole slots over the mounting screws or bolts on the bracket. Rotate the canopy until the screw or bolt heads lock in place at the narrow section of the key hole. Step 3. Attach the canopy cover to the bottom of the canopy and screw it into place.
LIGHT INSTALLATION Step 1. Remove the pre-installed bolts on the fan motor assembly. Step 2. Feed the wire connectors through the middle of the light plate. Install the light plate onto the motor assembly and secure it by replacing and retightening the bolts. Step 3. Connect the LED light kit to the light plate using its magnetic suction-cup bolts. Light Plate Step 4. Connect the wire plugs of the LED light kit to the wire connectors (blue to blue and white to white).
REMOTE CONTROL OPERATION Install the remote control holder onto any wall or suitable flat surface using the two steel screws. Upon first use, connect the remote control to its receiver in the fan by pressing the emitter's "LI" and "Hi" button for 3 seconds. There should be a beep to announce that the remote has successfully connected to its receiver. (Note that this programming cannot be done for the first 30 seconds after the receiver is turned on.
TROUBLESHOOTING Potential Problems Common Solutions Check fuses and/or circuit breakers and reset if needed. Cut off power to the fan and check its internal electrical connections. Fan blades don't rotate Replace the remote control’s batteries. Check that the fan cover is correctly placed and no bolt interfere with the movement of the blades. Contact customer service to replace a faulty remote control. Check that all bolts, screws, and fasteners are well tightened.
