User manual

ManualsBrandsMERTEN ManualsOutlets & SocketsCeiling, Wall PIR motion detector 220 ° Polar white IP55

V5095-581-04 04/13

– Mounting bracket (Art. no. 56529.)

– Remote control for radio ARGUS 220 CONNECT

(Art. no. 509590)

DANGER

Risk of serious damage to property and per-

sonal injury, e.g. from fire or electric shock,

due to incorrect electrical installation.

Safe electrical installation can only be ensured if

the person in question can prove basic knowl-

edge in the following areas:

• Connecting to installation networks

• Connecting several electrical devices

• Laying electric cables

• Outdoor electrical installation

These skills and experience are normally only

possessed by skilled professionals who are

trained in the field of electrical installation technol-

ogy. If these minimum requirements are not met

or are disregarded in any way, you will be solely li-

able for any damage to property or personal inju-

ry.

The radio ARGUS 220 CONNECT (referred to below as

the ARGUS) is a movement detector for indoor and out-

door installation.

Functions:

• 220° surface monitoring for large house fronts and

sections of the house (max. range. 16 m)

• 360° short-range zone (approx. 4 m radius)

• LED function display for fast alignment at the installa-

tion site.

• Operating elements are protected under the easily ac-

cessible cover plate.

• Can be installed on walls and ceilings without addi-

tional accessories.

• Horizontally, vertically and axially adjustable sensor

head for optimum adaptation to immediate surround-

ings

• Hide unwanted zones or sources of disturbance (e.g.

trees) using the segments supplied.

• Remote control for setting and operating the ARGUS

conveniently.

Radio ARGUS 220 CONNECT

Operating instructions

Art. no. 5095..

Accessories

For your safety

ARGUS introduction

ende

Movement/presence detectors are not suitable

for use as components of an alarm system.

Movement/presence detectors can trigger false

alarms if the installation site has been chosen un-

favourably.

Movement/presence detectors switch on as soon as

they detect a moving heat source. This can be a person,

but also animals, trees, cars or differences in tempera-

ture in windows. In order to avoid false alarms, the cho-

sen installation site should be such that undesired heat

sources cannot be detected (see section „Selecting the

installation site“).

The ARGUS operating elements are protected under the

cover plate. The arrow's position on the controllers

shows you the set values.

Using ARGUS with alarm systems

Connections, displays and operating

elements

A Wall connection box

B Top sect ion

C Cover plate

D Sensor head

E Contact pins

F Cable routing for connecting cable from under-

neath

G Cable routing for connecting cable from behind

H Terminal block for the connecting cable and for

locating the contact pins

A ARGUS settings controller

A = Operating mode

B = Learning mode (also for PC-Tool)

C = Reset

D = Adopt potentiometer settings

B Switching duration controller

C Brightness threshold controller

D Functional display (lights up each time move-

ment is detected)

E Brightness sensor (must not be covered)

F Sensitivity controller

Explanation of the symbols used

When selecting a suitable installation site, you should

take a number of factors into account so that the move-

ment detector operates optimally.

The following figure shows the ranges of the AR-

GUS at average temperature conditions and a

mounting height of 2.5 m. The range of a move-

ment detector can vary greatly depending on the

temperature.

Inner security zone A: Angle of detection 360° over

a radius of approx. 4 m.

Middle security zone B: Angle of detection 220°

with an area of detection of approx. 9 m x 18 m.

Outer security zone C: Angle of detection 220° with

an area of detection of approx. 16 m x 28 m.

Mounting height D: 2-3 m. For optimum monitoring,

we recommend a height of 2.5 m on a solid and even

base.

Minimum distance E to sources of optical interfer-

ence: 5 m If necessary, use the segments supplied to

shade the device.

Minimum distance F between luminaire and move-

ment detector: 5 m. If this distance cannot be

achieved, you can use the segments provided to

"mask" the light source from the area of detection.

Selecting the installation site

Correct

Not optimal

Incorrect

4 2 4 6 8 10 12 14 16 m

0 2 4 6 8 10 12 14 16 m

2,5

0,8 m

If possible, install the movement detector sideways to the

direction of movement.

To avoid the connected load being switched on due to

environmental influences, the ARGUS should be in-

stalled so that it is protected against rain and direct sun-

light. A raindrop running over the lens, for example, can

activate the movement detector.

If you wish to attach several movement detectors, install

them so that the detection areas of the individual move-

ment detectors intersect each other.

Dismantlement of the top section of the ARGUS

Installing the ARGUS to the wall

Feeding in the connecting cable

ARGUS installation

Installing the ARGUS on the ceiling

In order to install the ARGUS on the ceiling, you must ro-

tate the sensor head. Change the direction of rotation

once you have reached the end stops.

1 Turn the sensor head upwards as far as it will go.

2 Turn the sensor head clockwise as far as it will go.

3 Align the sensor head.

CAUTION

If not installed correctly, the device can be

damaged by condensation.

In the case of sloping ceilings, install the device

so that spherical head is pointing down and al-

ways at an angle of 15° - 90°. When the spherical

head points downwards, any water from conden-

sation could run down the device.

Type of protection IP 55 cannot be guaranteed if

the mounting bracket is not 15° - 90°.

Installing the ARGUS on corners and fixed pipes

You can attach the ARGUS to inner/outer corners or fixed

pipes using the mounting bracket (art. no. 56529x). You

can feed the connecting cable to the device from behind

through the mounting bracket.

15° - 90°