Power Screwdriver User Manual

ManualsBrandsMetra Electronics ManualsPower ScrewdriverACURA 99-7866

INSTALLATION INSTRUCTIONS FOR PART 99-7866

99-7866

APPLICATIONS

ACURA MDX 2001-2006

KIT FEATURES

• DIN Mount Radio Provision with Pocket

• ISO Mount Radio Provision with Pocket

A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Bracket Supports For Display

KIT COMPONENTS

TOOLS REQUIRED:

Small Flat Blade Screwdriver/ Panel Removal Tool

• Phillips Screwdriver • Socket Set

1-800-221-0932

TION

www.metr

aonline.com

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 99-7866 APPLICATIONS ACURA MDX 2001-2006 99-7866 KIT FEATURES • DIN Mount Radio Provision with Pocket • ISO Mount Radio Provision with Pocket KIT COMPONENTS A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Bracket Supports For Display B C A D TOOLS REQUIRED: Small Flat Blade Screwdriver/ Panel Removal Tool • Phillips Screwdriver • Socket Set 1-800-221-0932 © COPYRIGHT 2003-2008 www.metraonline.
PAGE 2
99-7866 TABLE OF CONTENTS Dash Disassembly - ACURA MDX 2001-2006. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Kit Preparation - Display Unit Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Kit Assembly - DIN Mount Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . 3 - ISO Mount Radio Provision with Pocket. . . . . . . . . . . . . . . . . . . . . . . . 4 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 3
99-7866 DASH DISASSEMBLY ACURA MDX 2001-2006 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove trim panel around radio/display including a/c vents.. (Figure A) 3 Remove (6) mounting screws and remove the audio/display unit from the dash. (Figure B) 4 Remove (8) screws from the audio unit and (6) screws from the display unit and remove the brackets from the audio/display assembly. Continue to kit preparation.
PAGE 4
99-7866 KIT PREPARATION DISPLAY UNIT ASSEMBLY *Note: Refer also to the instructions included with the aftermarket radio. A 1 Using the mounting screws from the display unit, attach the brackets supplied with the kit by aligning the guide pins on the display with the holes on the bracket. (Figure A) 2 Align guide pins on bottom of display unit with holes on top of housing and attach the unit to the housing using the (2) screws previously removed. (Figure B) Continue to kit assembly.
PAGE 5
99-7866 KIT ASSEMBLY DIN MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Slide the DIN cage into the radio housing and secure by bending the metal locking tabs outward. (Figure A) 2 Slide the aftermarket radio into the DIN cage until it snaps into place. (Figure B) Continue to final assembly.
PAGE 6
99-7866 KIT ASSEMBLY ISO MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Mount the ISO Brackets to the radio using the screws supplied with the radio. (Figure A) 2 Slide the radio into the radio opening until it snaps into place. (Figure B) 3 Snap the ISO Trim Plate onto the front of the Radio Housing. (Figure B) Continue to final assembly.
PAGE 7
99-7866 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation.
PAGE 8
99-7866 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV.