Manualshelf

Instructions / Assembly

ManualsBrandsMetropolitan ManualsChandeliersMass Transit 12-Light Brushed Nickel and Sand Coal Wagon Wheel Pendant with Clear Ribbed Glass Shades
12
INSTALLATION INSTRUCTIONS
Item#N7872-420-L (New. 04/15/2020)
READ AND SAVE THESE INSTRUCTIONS
WARNI NG! S HUT P OWE R OFF AT F USE OR CI RCUIT BRE AKE R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Page: 1/2
Fig. 1
Fig. 3
LA-3263E
PREPARATION (Fig. 1)
1. Shut off power at the fuse box or circuit breaker box and
remove the old fixture including the mounting hardware.
2. Carefully unpack your new fixture and lay out all the parts
in a clean area. Take care not to misplace any small parts
necessary for installation.
ASSEMBLING THE FIXTURE WITH CHAIN LOOP (Fig. 2)
3. Screw longest rod (O) onto the all thread (I) on top of
fixture.
4. Determine the desired hanging height and thread rods
(F1, F2 and F3) to the longest rod (O). Screw loop (H1) to
rod (F1). Note: Pass the wires carefully through each rod
as you assemble.
5. Attach the quick link (G) to loop (H1) and loop (H2) on the
canopy (D). Carefully feed the wires through loop (H1),
quick link (G), and loop (H2).
6. Attach the mounting plate (B) to the junction box using the
junction box screws (C) (SIZE: #8-32N, L0.5"). The side of
the mounting plate marked “GND” must face out.
7. The support cable is provided to support the weight of the
fixture while wiring. Raise the fixture to the mounting plate
(B) and attach hook (M), on the end of support cable (E),
into a slot located on mounting plate (B). Carefully allow
the support cable (E) to support the weight of the fixture
while wiring (Fig.1).
CONNECTING THE WIRES (Fig. 3)
8. Connect the electrical wires as shown in fig.3, making
sure that all wire connectors are secured. If your junction
box has a ground wire (green or bare copper), connect the
fixture’s ground wire to it. Otherwise, connect the fixture’s
ground wire directly to the mounting plate (B) using the
green screw provided. After wires are connected, tuck
them carefully inside the junction box.
COMPLETING THE INSTALLATION (Fig. 1)
9. Raise the canopy (D) onto mounting plate (B) and secure
with screws (A).
10. Install (12) twelve G9 base bulbs (K) up to 40 watts each
or CFL or LED equivalent (not included) in accordance
with the fixture specification—DO NOT EXCEED THE
MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA
PUISSANCE NOMINALE MAXIMALE!).
11. Place the glass shade (J) over the socket (L) and turn to
secure it to the fixture.
Your installation is now complete. Return power to the junction
box and test the fixture.
Note: Illustration (Fig. 1) on this manual is for installation
purposes only. It may or may not be identical to the fixture
purchased.
Set# A-021-150D
-Mounting plate
-Ground screw
-Mounting screw*2
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
White
(Neutral)
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
Green
(Ground)
B
C
E
A
D
F1
F2
F3
O
I
G
H2
H1
M
J
K
L

Summary of content (2 pages)