www.mgeups.
MGE UPS Systems 1660 Scenic Avenue Costa Mesa, CA 92626 (714) 557-1636 For service call 1-800-438-7373 www.mgeups.com IMPORTANT SAFETY INSTRUCTIONS Read before installing product SAVE THESE INSTRUCTIONS. This manual contains important instructions for 89347, 89348, and 89349 that should be followed during installation and maintenance of the UPS and batteries. Thank you for selecting an MGE UPS SYSTEMS product to protect your electrical equipment.
Introduction CAUTION: Safety of persons ◗ The UPS has its own internal power source (the battery). Consequently, the power outlets may be energized even if the UPS is disconnected from the AC-power source. ◗ Dangerous voltage levels are present within the UPS. It should be opened exclusively by qualified service personnel. ◗ The UPS must be properly earthed. Measurements are required to ensure that the total leakage current of the UPS and the protected equipment does not exceed 3.
Foreword Using this document Information may be found in two ways, using: ◗ the contents; ◗ the index. Pictograms IMPORTANT: Important instructions that must always be followed. NOTE: Information, advice, help. WARNING: Indicates present eminent danger, precautionary action required. CAUTION: Indicates to proceed with caution, precautionary action required. Visual indication. Action. Audio indication. In the illustrations on the following pages, the symbols below are used: LED off. LED on.
Contents 1. Presentation 1.1 Overall view .................................................................................................................................. 7 Tower position ..................................................................................................................................7 Rack position....................................................................................................................................7 2. 3. 1.2 Back ......................
Contents 6. Appendices 6.1 Technical data ..............................................................................................................................24 Simplified diagram..........................................................................................................................24 Technical characteristics ................................................................................................................25 Examples of battery backup times ......................
1. Presentation 1.1 Overall view Tower position Dimensions in inches (W x H x D) Evolution 2200 Evolution 3000 17.24 (19") x 3.56 (2U) x 25.
1. Presentation 1.2 Back Pulsar Evolution 2200 1 USB communications port. 2 RS232 communications port. 3 Connector for automatic detection of an additional battery module. 4 Data-line protection. 5 Slot for communications-card option. 6 Connector for an additional battery module. 7 Output circuit breakers. 8 Six receptacles for direct connection of protected equipment. 9 Two programmable receptacles (1 and 2). 1 Data line protection R IN 1 Programmable RS232 34Z5 U.P.S.
1. Presentation 1.3 Control panel 15 Illuminated ON/OFF button for the receptacles. 16 Operation on battery power. 17 UPS fault. Battery fault. 18 Overload. 19 Group 1 programmable receptacles supplied with power. 1 2 20 Group 2 programmable receptacles supplied with power. 21 Booster or fader mode. % 22 Bar graph indicating percent load at output. % 23 Bar graph indicating the battery charge level. 76 to 100%. 51 to 75%. 26 to 50%. 0 to 25%.
2. Installation 2.1 Unpacking and parts check 26 25 27 28 29 30 31 SAR P U Lut io n Ev ol 0 300 32 26 RS232 communications cable for Windows Operating Systems. For UNIX/Linux Operating Systems, please order, for free, the following part number: 66090 27 USB communications cable. 28 Telescopic rails for mounting in 19" bay with mounting hardware. 29 Two securing systems for equipment power cords. 30 CD-ROM with the Solution-Pac and UPS Driver software. 31 Product documentation.
2. Installation 2.2 Upright installation (tower position) Connect the two supports for the upright position.
SAR P U L tion E v o l u0 300
2. Installation 2.4 Connecting the protected equipment CAUTION: Check that the indications on the rating plate on the back of the UPS correspond to your AC-power system and to the actual electrical consumption of all the equipment to be connected to the UPS. BATTERY CONNECTOR Volt: 72Vdc 40A U.S. PAT. No. 6,094,363 1 - Remove the power cord supplying the equipment to be protected. - Pulsar Evolution 2200/3000/3000 XL: Connect the supplied input power cord 10 to the AC power wall receptacle.
2. Installation 2.5 Connection to the RS232 or USB communications port (optional) CAUTION: The RS232 and USB communications ports cannot operate simultaneously. 26 1 - Connect the RS232 26 or USB 27 communications cable to the serial port or the USB port on the computer. 27 RS232 TO BATTERY CABINET 2 1 344-50297-00 2 - Connect the other end of the communications cable 26 or 27 to the RS232 2 or USB 1 communications port on the UPS.
2. Installation 2.7 Installation of the communications-card option RS232 1 - Remove the slot cover 5 secured by two screws. TO BATTERY CABINET 2 - Insert the card in the slot. 5 344-50297-00 It is not necessary to shut down the UPS to install the communications card. IN OUT WARNING 72Vdc, 9Ah Only for 3000 3 battery cabinets max for 3000 12 battery cabinets max for 3000XL Pb Data line protection SITE WIRING FAULT Slot for the communications-card option.
3. Operation 3.1 Start-up 15 16 17 1 2 % % 1 % Page 16 - 3400723100/AD 2 % Press the ON / OFF button 15 . The buzzer beeps and all the LEDs come ON. The buzzer beeps twice during the self-test, then button 15 remains ON, indicating that the receptacles are supplied with power. - AC power is present: Only button 15 is ON. The protected equipment is supplied by the AC-power source. - AC power is absent: Button 15 and LED 16 are ON.
3. Operation 3.3 Operation on battery power (following failure of AC-input power) Transfer to battery power The AC-input power is out of tolerances, LED 16 goes ON. During operation on battery power, the buzzer beeps every ten seconds. The equipment connected to the UPS is supplied by the battery. 16 1 2 % % Threshold for the low-battery warning When the threshold is reached, the buzzer beeps every three seconds. The low-battery warning threshold can be set by the user, with the “UPS Driver” software.
3. Operation 3.4 Personalization (optional) Function Personalization parameters can be set and modified using the UPS Driver software installed on a computer that is connected to the UPS (see section 2.5 Connection to the RS232 or USB communications port). Check that the RS232 26 communications cable is connected. UPS Driver installation: 1 - Insert the Solution-Pac CD-ROM containing the UPS Driver software in the drive of a PC running Windows.
3.
4. Maintenance 4.1 Trouble-shooting Troubleshooting not requiring MGE UPS SYSTEMS after-sales support (all versions) Indication Signification Correction LED 18 flashes and the buzzer beeps once. UPS overload. The power drawn by the connected equipment exceeds UPS capacity. Check the power drawn by the equipment and disconnect any non-priority devices. LED 17 flashes. A battery fault was detected during the automatic battery test. Replace the battery module (see section 4.2).
3400723100/AD - Page 21
4. Maintenance F - Remove the screw securing the battery cover. G - Remove the cover. F G H - Disconnect the battery module. I - Remove the battery module. H I Battery Replacement Chart Component Manufacturer 12V 7Ah (in 2200VA) 12V 7Ah (in 3000VA ) Panasonic Panasonic Manufacturer’s Catalog Number LC-R127 LC-R129 Installation of the new battery module Carry out the above operation in reverse order. CAUTION: risk of electric arc when connecting the battery.
5. Environment This product has been designed to respect the environment: It does not contain CFCs or HCFCs. UPS recycling at the end of service life: MGE UPS SYSTEMS undertakes to recycle, by certified companies and in compliance with all applicable regulations, all UPS products recovered at the end of their service life (contact your MGE branch office). Packing: UPS packing materials must be recycled in compliance with all applicable regulations. WARNING: This product contains lead-acid batteries.
6. Appendices 6.
6. Appendices Technical characteristics Output rating AC-input power ◗ Voltage ◗ Frequency Output power (operation on battery power) ◗ Voltage ◗ Frequency Battery Environment Noise level (operation on AC-input power) ◗ Operating temperature ◗ Relative humidity ◗ Pulsar Evolution 2200 Pulsar Evolution 3000 Pulsar Evolution 3000 XL 1920 VA / 1540 W (1) 2880 VA / 2000 W 2568 VA / 2000 W Single phase, 80 V to 153 V (1) 47 Hz to 70 Hz (50 Hz system) or 56.
6.
6. Appendices 6.2 Glossary Backup time Time that the connected equipment can operate on battery power if AC-input power fails. Bar graph Device on the front panel indicating the percent remaining backup time or the percent load. Battery module (additional) Additional battery modules connected in parallel to increase the UPS backup time.
6. Appendices 6.3 Index A Automatic start ................................................................18 B Bar graph ..........................................................................9 Battery Additional modules ....................................................8 Backup time ............................................................26 End of backup time..................................................17 Fault ..........................................................................
1660 Scenic Avenue Costa Mesa, CA 92626 USA www.mgeups.