Instruction manual

ManualsBrandsMichley Electronics ManualsDomestic AppliancesLSS-505

Please read the instruction book carefully

before operating the sewing machine.

Please save this manual in a safe place.

This sewing machine is for Household Use.

Instruction Manual

Model: FHSM-505

Mini multi-purpose sewing machine

Problem Problem cause Amendment

No power or the machine

runs slowly

Skipping stitches

Bobbin thread cannot be

drawn up

Thread keeps breaking

Stitches too loose or

uneven

Needle breaks

·Batteries are installed

incorrectly

·Reinstall the batteries

making sure they are the

correct way around

·Batteries are low

·Use new batteries

·Adaptor power inadequate ·Use compatible adaptor

·Needle eye not in the

middle

TROUBLESHOOTING

·Remove and re-insert the

needle with the flat side of

the needle to the back

·Needle bent ·Remove and re-insert a

new needle

·Presser foot too loose ·Tighten the presser foot

·Lower thread has been

used up

·Replace with new full

bobbin

·Needle threaded incorrectly

·Re-thread the needle,

making sure it is threaded

from the front to the back

·Needle bent ·Remove and re-insert a

new needle

·Needle shank not properly

seated

·Remove and re-insert a

new needle

·Thread tension dial, thread

guide or thread pulling bar

too tight

·Loosen the thread tension

between 3-5 number

·Thread blocked by upper

bobbin

·Upper thread too loose

·Pull out the spool pin and

make the bobbin or thread

run smoothly

·Needle bent or deformed

·Remove and re-insert a

new needle

Summary of content (6 pages)

PAGE 1
TROUBLESHOOTING Problem No power or the machine runs slowly Problem cause Amendment ·Batteries are installed incorrectly ·Reinstall the batteries making sure they are the correct way around ·Batteries are low ·Use new batteries Mini multi-purpose sewing machine Instruction Manual ·Adaptor power inadequate ·Use compatible adaptor Skipping stitches Bobbin thread cannot be drawn up Thread keeps breaking ·Needle eye not in the middle ·Remove and re-insert the needle with the flat side of the needle
PAGE 2
FEATURES ADJUSTING STITCHING 1. As shown in the picture A, normal stitching shall have top and bottom threading neither over tight or loose. Top thread Cloth Bottom thread Fig.A 2. If the bottom threading looks like a straight line, which indicates the top thread is too loose. Please turn in thread damp clock wise to increase pressure until the stitching returns to normal. Fig.B 3.
PAGE 3
Please read all instructions before using this appliance carefully and keep them in a safe place for future use. FEATURES DRAWER On the side of the sewing machine (towards the rear) is a drawer for the handy storage of accessories BOBBIN WINDING Put a spool of thread on spool pin (Fig.11). Place the thread to the right of the bobbin wider tension disk Push the bobbin into the bobbin wider pin and push it to the left. (Fig.13) Wind thread clockwise around bobbin several times.
PAGE 4
NAME OF PARTS FEATURES Front view Take up lever Upper thread tension dial Pattern selection dial Handwheel Thread Cutter Light Needle clamp screw Reverse button Power off & speed switch Drawer Bottom bobbin 8 STITCH FUNCTIONS 1. The sewing machine has a choice of 8 different stitch types /lengths. To select the stitch you require, look at the diagrams numbered 1-8 on the front of the sewing machine, choose the corresponding number on the dial is lined up with the arrow.
PAGE 5
SEWING CONNECTING THE SEWING MACHINE TO THE MAINS POWER SUPPLY 1. Turn the hand wheel on the side of the sewing machine anticlockwise to raise the needle to its highest position. Lift the presser foot and place the fabric you wish to sew under the presser foot (Fig.7). 2. Lower the presser foot (Fig.8). 3. The sewing machine can be operated in two ways: with the foot controller or with the “power off/speed switch”.
PAGE 6
THRENDING THE SEWING MACHINE REPLACING THE BOBBIN Threading upper thread Caution: When threading the sewing machine make sure that the“power off/speed switch” is in the OFF position and follow the steps 1-6 below. Turn hand wheel counter clockwise until the needle is in the highest position. 1. Turn the hand wheel counter clockwise until the needle is in the highest position. Raise presser foot lifter. 2. Pull the slide plate forward and remove the empty bobbin 3.