INSTALLATION & OPERATIONAL INSTRUCTIONS FREESTANDING ASME A112.19.7-2006 ANSI-Z124.
INSTALLATION INSTRUCTIONS & OWNER’S MANUAL (Refer to individual model sheets for specifications) BEFORE BEGINNING INSTALLATION, CHECK THE FOLLOWING ITEMS AND READ THE INSTRUCTIONS CAREFULLY. CHECK ENTIRE UNIT FOR CONCEALED DAMAGE. If there is any damage, DO NOT INSTALL! Shipping damages must be reported to the carrier immediately. All damage must be discovered and reported prior to installation in order to have it covered under the warranty! COMPARE COLOR OF UNIT WITH OTHER FIXTURES.
READ AND FOLLOW ALL INSTRUCTIONS 1. 6. A green colored terminal (or a wire connector marked `G’, `GR’, `GROUND’, or `GROUNDING’) is provided within the terminal compartment. To reduce the risk of electrical shock. connect this terminal or connector to the grounding terminal of your electrical service or supply panel with a continuous green insulated copper wire equivalent in size to the circuit conductors supplying the equipment. but no smaller than No.10 AWE (5.
INSTALLATION PREPARATION INSTALL DRAIN HARDWARE 1. Clean, level and prepare the floor for installation. 6. 2. Place the unit in the exact installed position on the floor and trace the outline of the bath with a pencil or any erasable marking (figure 1). Apply a bead of clear silicone or plumbers putty around the Drain Body and pass it through the drain hole (figure 3). 7. Apply plumbers putty to the Washer and slide it over the bottom of the Drain Body (figure 3).
INSTALLATION CONTINUED PREPARE TAIL PIECE All parts involved in tail piece installation are provide by the installer (figure 5). 10. Drain waste vent must always be installed according to local standard. Verify the placement of the bathtub before drilling the hole for the drain waste vent. 11. Install 1 1/2 inch rubber slip gasket over the drain waste vent. 12. Cut tail piece to desired length (will vary for each installation). 13. Slide tail piece nut over tail piece towards flanged end. 14.
INSTALLATION CONTINUED INSTALL BATHTUB COMPLETE BATHTUB INSTALLATION 16. Apply a generous bead of adhesive or silicone to the bottom of the tub supports (figure 6). 19. 17. Then apply a bead of tub and tile caulk around the edge of the base (figure 6) Fill the tub with water to the overflow and then drain the tub while inspecting the waste connections below the floor for leaks. Access from below will be necessary for this step (figure 8). Figure 6 Figure 8 18.
INSTALLATION CONTINUED PLUMBING ROUGH-IN ELECTRICAL The bath waste opening protrudes below the base approximately one inch. You may be required to cut a hole in the subfloor to accommodate bath waste. In slab on grade or prestressed concrete floors where cutting is not desired, the tub may be raised up by building the platform higher and using extra mortar under the tub. If a joist must be notched, verify that structure will not be weakened. Remove only what is necessary.
INSTALLATION CONTINUED AVANO TOUCH PLUS START UP AND OPERATIONAL INSTRUCTIONS 4 3. 3 2 4. 1 5 1. 5. Pump On/Off: 1st Press - The pump starts. 2nd Press - The pump stops. Light Button: Operates LED lighting systems. 2. Increase Pressure 6. 6 Use Button to decrease air jet speed while the blower is running. Press & hold to increase the blower speed, release pressure at the desired speed. Use Button to increase air jet speed while the blower is running.
INSTALLATION CONTINUED 120V/60Hz Variable Blower & On/Off Pump & Light Schematic For any maintenance or repair the Fiji shell can be removed by flipping the tub over, locating and removing the 4 plastic nubs and loosening the securing screws underneith. Then the entire shell can easily be removed. If the tub is fully installed but must be uninstalled for maintenance or repair the caulking must be removed completely, the tub must be cleaned and new caulking is to be applied for reinstallation.
USER MAINTENANCE USER SHOULD periodically flush operating system (not to exceed 90 days). As a minimum, shall consist of filling and running system and draining. Spa World recommends flushing with a mild solution of water and sanitizer such as chlorine or other commercially available whirlpool bath flushing products. DO NOT use abrasives. They may dull or scratch surface of the acrylic. DO NOT use oil based solvents. Clean with only a damp cloth or mild detergent or any common glass cleaner.
LIMITED WARRANTY COVERAGE READ CAREFULLY, THE WARRANTY APPLIES ONLY TO ORIGINAL OWNER 10 YEARS STRUCTURAL Written notice of any malfunction or defect must be given within ten (10) days of the time it is discovered, to Spa World, 5701 NW 35th Avenue, Miami, Florida 33142. Spa World reserves the right to inspect the malfunction or defect on location.
NOTES INSTALLER INFORMATION DATE OF INSTALL: INSTALLER’S NAME: PLUMBER: CONTRACTOR: LICENSE #: 11
IMPORTANT: READ AND SAVE THESE INSTRUCTIONS. INSTALLER: SAVE INSTALLATION INSTRUCTIONS WITH HOMEOWNER HOMEOWNER: KEEP INSTALLATION INSTRUCTIONS FOR FUTURE REFERENCE Please leave owner’s manual with warranty. If you have any problems or questions during installation, please call technical service at 888-260-0996 Record the numbers here for handy reference: Model No. Serial No. Date of Purchase M a de in USA Manufactured by MidWest Tubs A Division of Spa World Corp.