Operating Instructions Dishwasher G 1202 To prevent accidents and appliance damage read these instructions before installation or use. en - US, CA M.-Nr.
Contents IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Guide to the dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Before using for the first time. . . . . . . . . . . .
Contents Additional options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Turbo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Tab. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Delay Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IMPORTANT SAFETY INSTRUCTIONS WARNING – When using your dishwasher, follow basic precautions, including the following: Read all instructions before installation or use of the dishwasher to prevent injury and machine damage. Use the dishwasher only for its intended purpose. This appliance is intended for residential use only. Keep these operating instructions in a safe place and pass them on to any future user.
IMPORTANT SAFETY INSTRUCTIONS Installation ~ The dishwasher must be installed and connected in compliance with the installation instructions. ~ Installation and repair work should be performed by a Miele authorized service technician. Work by unqualified persons could be dangerous and may void the warranty. ~ , WARNING - Fire hazard Do not cover or crush the plug of the appliance. Ensure that the cabinet opening for the dishwasher provides ample space for the plug.
IMPORTANT SAFETY INSTRUCTIONS Use ~ To reduce the risk of injury, do not allow children to play in, on or near the dishwasher. ~ Only use detergents and rinse aids recommended for residential dishwashers. Keep all detergents and rinse aids out of the reach of children. Do not inhale or swallow detergents. ~ Only use the dishwasher if all panels ~ Dishwasher detergents contain irritant are properly in place. ~ Do not tamper with the controls.
Guide to the dishwasher a Upper spray arm (not visible) g Triple filter system b Cutlery tray h Data plate c Upper basket i Child Safety Lock in the door handle (not visible) d Middle spray arm e Air inlet for drying (depending on model) f Lower spray arm j Rinse aid reservoir k Dual compartment detergent dispenser l Salt container 7
Guide to the dishwasher Control panel a Program selection f Check/Refill indicators b Time display g Start/Stop button with indicator light c Additional options with indicators h Delay start button with indicator light d Program sequence display i Options button e On/Off button K j Program button 8
Caring for the environment Energy saving washing This dishwasher is exceptionally economical in the use of water and electricity. For best results follow these tips: ^ For lowest energy consumption you may connect the dishwasher to a cold water source. ^ For fastest possible wash times, with slightly higher energy consumption, connect the dishwasher to a hot water source. ^ Make full use of the baskets without overloading for the most economical washing. ^ Use the correct amount of detergent and rinse aid.
Before using for the first time To open the door Child Safety Lock ^ Press the release catch inside the door grip. The Child Safety Lock is designed to prevent children from opening the dishwasher. If the door is opened during operation, the dishwasher will stop running. Once the door is closed the program will restart. To close the door ^ Push the baskets in. ^ Lift the door and push until it clicks into place. 10 ^ To lock the door, push the slider below the door grip to the right.
Before using for the first time Water softener Every dishwasher is tested before leaving the factory. Any water remaining in the machine is from the final factory test and does not indicate that the machine has been used. To achieve good cleaning results, the dishwasher needs soft water. Hard water results in calcium deposits on dishware and in the dishwasher. If your tap water hardness is above 4 °d (4 gr/gal [US]), the water should be softened.
Before using for the first time Programming the water softener To exit the programming mode at any time, turn the dishwasher off with the "K" button. ^ Turn the dishwasher off with "K". ^ Press and hold the "Program" and "Start / Stop" buttons simultaneously turn the dishwasher on with "K". Hold the "Start / Stop" button until the "Start / Stop" indicator lights. If it does not come on, start over. ^ Press the "Delay Start" button twice. The "Delay Start" indicator flashes twice in intervals.
Before using for the first time Filling the salt container ,Inadvertently filling the salt container with dishwashing detergent will damage the water softener. ,Only use water softener salt specially formulated for dishwashers. Other salts may contain insoluble additives which can impair the water softener. ^ Remove the lower basket and unscrew the salt container lid. When opening the salt container, water will run out. Open the container only to refill salt.
Before using for the first time Rinse aid Rinse aid helps to prevent spotting on dishes and glassware. The rinse aid is filled in the reservoir and the set amount will be automatically dosed. ,Filling the rinse aid reservoir with detergent will damage the reservoir. Only pour rinse aid formulated for residential dishwashers into the reservoir. When using "Tab" detergents rinse aid is not needed. Adding rinse aid ^ Pour liquid rinse aid into the reservoir until it is visible on the surface of the screen.
Before using for the first time Rinse aid indicator Adjusting the dosage When the rinse aid indicator first comes on, there will be enough rinse aid left for 2 - 3 washes. The dosage selector is preset to 3. This dispenses approximately 3 ml of rinse aid per program. It can be adjusted from 0 to 6. ^ The rinse aid indicator on the control panel will light when the rinse aid reservoir needs refilling.
Loading the dishwasher ,Do not wash items soiled with ash, sand, wax, grease or paint in the dishwasher. Ash and sand do not dissolve and will be distributed throughout the inside of the dishwasher. Wax, grease and paint will cause permanent discoloration and damage to the dishwasher. ^ Scrape food from dishes before placing them in the dishwasher, rinsing is not necessary. ^ Some foods contain natural dyes, e.g. carrots or tomatoes.
Loading the dishwasher Items not recommended for dishwashing – Cutlery with wooden handles – Wooden cutting boards – Glued items such as old knives with handles glued together around the shank of the blade – Handmade craft items, antique, metal trimmed or decorative glassware Glassware: – There are no standard guidelines for washing glassware, when in doubt wash by hand. – When purchasing new dishes, glasses and cutlery, make sure they are dishwasher safe.
Loading the dishwasher Cutlery tray ^ Arrange the cutlery as shown in the cutlery tray. For easier unloading cutlery should be grouped in zones, one for knives, one for forks, one for spoons, etc. Place knives with the cutting edge down and forks with the prongs between the holders. Spoons should be placed in the opposite direction with the handles between the holders so that water can run off more easily. The upper spray arm must not be blocked by tall cutlery items. The cutlery tray insert is removable.
Loading the dishwasher Upper basket Adjustable cup rack ,Always use the dishwasher with the upper and lower basket in place. ^ Raise the rack to make room for tall glasses. Lower it to double stack smaller pieces. ^ Load the upper basket with small, lightweight, or delicate items such as cups, saucers, glasses, dessert bowls and flat pans. ^ Long items such as soup ladles, mixing spoons and long knives should be placed lying down across the front of the upper basket.
Loading the dishwasher Adjusting the upper basket The upper basket can be raised or lowered to accommodate tall items. The basket can also be angled to fit tall items in both, the upper and lower baskets. The angles should not be set to opposite extremes. This will block the middle spray arm. Take care when sliding the basket in and out in this position. ^ Slide out the upper basket. ^ Pull up the levers at the sides of the upper basket and adjust the basket height.
Loading the dishwasher Lower basket Foldable spikes Both rows of spikes in the front section of the basket can be folded down, to create more room for larger dishware, e.g. pots, pans and bowls. ^ For larger and heavier items such as plates, serving platters, saucepans, bowls, etc. Small plates and saucers can also be arranged in the lower basket. ^ Press the yellow lever down a and fold down the spikes b.
Loading the dishwasher Removeable PlateGuard Plus with SteamGuard Removing the insert: This insert is ideal for cups, glasses, plates, bowls, pots and pans. ^ Press the insert downwards a and at the same time press the catch inwards b. ^ To arrange tall items the cup rack can be raised. ^ The stemguard can be used to hold the stems of glassware or coffee cup handles. Replacing the insert: ^ Place the insert back into the lower basket.
Loading the dishwasher Vase / Bottle insert (depending on model) The vase / bottle insert can be used to rinse narrow items, e.g. vases, baby bottles, etc. ^ Place the insert into the lower basket as shown in the illustration. If placed anywhere else, water will not reach all surfaces. The item will not be properly cleaned.
Basket accessories Additional inserts for the upper and lower baskets may be purchased from your Miele dealer or Miele. Depending on the model some accessories come standard with the machine.
Use Detergent ,Dishwasher detergents contain irritant and corrosive ingredients. Avoid inhaling or swallowing dishwasher detergent. Keep children away from detergent. Fill the detergent dispenser only when you are ready to start the dishwasher. ,Only use detergents formulated for domestic dishwashers. You can use powder, gel or tab detergents. Follow the dosage information on the detergent packaging. Detergent tabs are not recommended for use with the program "Express".
Use Adding detergent ^ To open, press the latch on the detergent dispenser. The flap will spring open. The flap is always open at the end of a program. ^ Use one tab or add powder or gel detergent to compartment II and close the flap. ^ If a Pre-rinse is desired, and available for your chosen program, add 1 teaspoon (5 ml) of detergent to compartment I. The horizontal marks in compartment II indicate the levels of approximately 1 ¼ and 2 tablespoons (20 and 30 ml) respectively.
Use Turning on ^ Open the water supply, if closed. ^ Open the door. ^ Make sure the spray arms can rotate freely. ^ Turn the dishwasher on "K". The "Start/Stop" indicator flashes and the indicator next to the last program selected is lit. Selecting and starting a program Choose your program according to the type of load and soiling. See the "Program Guide" for more information. ^ Select the desired program with the "Program" button. The program indicator of the selected program lights.
Program guide Program When to use Program sequence Pre-rinse 1 Main wash 2 X 1 X X X X X X X X X X X For normally soiled dishware China & Crystal as For temperature sensitive glassware and required lightly soiled dishware, use 50% of normal detergent amount X SaniWash Extended wash time, for sanitizing normally soiled dishware with dried on food X Express "Quick program" for lightly soiled dishware, e.g.
Use Time display At the end of a program Before the program starts, the time display shows the running time of the selected program in hours and minutes. During the running program the remaining time is shown in the time display. The program is complete when a "0" appears in the time display and the "End" indicator lights up. The running time for the same program may vary depending on the intake water temperature, load size and soiling.
Use Interrupting a program A program is interrupted as soon as the door is opened. If the door is closed, the program will continue from where it was interrupted. ,Open the door with care. The water in the dishwasher is hot. Danger of scalding. Before closing the door again, leave it ajar for approx. 20 secs. This will enable the temperature in the wash cabinet to settle. Close the door firmly until it clicks into place.
Additional options Options Tab With the "Options" button the functions "Turbo" and "Tab" can be selected. To achieve the best results, the dishwasher can be programmed for the type of detergent being used. The "Options" button can be used to select between normal detergents (powder or gel) and tabs. ^ Turn the dishwasher on "K" . The "Start/Stop" indicator flashes. ^ Press the "Options" button until the desired function lights up.
Additional options Delay Start ^ Press the "Start/Stop" button. The starting time of a program can be delayed. The start time can be delayed from 30 minutes to 24 hours. The indicator lights up. With a delay start time between 30 minutes and 9 hours 30 minutes the delay is set in 30 minute increments. For 10 hours or more it is set in one hour increments. When using the "Delay Start" function, make sure that the detergent compartment is dry before adding detergent. Wipe dry with a cloth if necessary.
Additional options Default settings All settings can be reset to the factory default. ^ Turn the dishwasher off "K". ^ Press and hold the "Start/Stop" button and at the same time turn the dishwasher on "K". Hold the "Start/Stop" button until the "Start/Stop" indicator lights up. If it does not come on, start over. ^ Press the "Delay Start" button 12 times. The "Delay Start" indicator gives on long flash and two short flashes in intervals. The time display shows if a setting was changed.
Frequently asked questions With the aid of the following guide, minor problems can be fixed without a service call. ,Repairs should only be carried out by a qualified and trained person in accordance with local and national safety regulations. Unauthorized repairs could cause personal injury or machine damage. Technical faults Problem The Start/Stop indicator does not flash after the dishwasher was turned on "s". The dishwasher stops during a program.
Frequently asked questions Problems water intake/drain Problem The "Intake / Drain" indicator is flashing. The dishwasher stops. The "Intake / Drain" indicator flashes. The time display shows FXX. Possible fault The water supply is shut off. Fault F12/F13: Water intake fault. Fault F11: Water drain fault. There may be water in the wash cabinet. Solution Open the water supply all the way. Before fixing the fault: – Turn the dishwasher off "s". – Open the water supply all the way.
Frequently asked questions General problems with the dishwasher Problem The display turns off. Possible fault The dishwasher has gone into "Standby" mode to save energy. Detergent is left in the The dispenser was damp dispenser at the end of when detergent was a program. added. Detergent residue is The detergent lid blocking the catch. cannot be closed properly. This is not a fault. It is the The door and the interior walls are still normal operating mode of wet after a program has the drying system.
Frequently asked questions Sounds Problem There is a knocking noise in the wash cabinet. There is a rattling noise in the wash cabinet. There is a knocking noise in the water pipes. Possible fault Solution The spray arm is hitting an Interrupt the program, item in the basket. rearrange items blocking the spray arms. Items are not secure in the Interrupt the program and wash cabinet. rearrange loose pieces. This may be caused by the This has no effect on the installation or the diameter dishwasher.
Frequently asked questions Poor cleaning results Problem The dishes are not clean. Possible fault The dishes were not loaded correctly. The program was not powerful enough. Solution See "Loading the dishwasher". Select a more intensive program, see "Program Guide". Not enough detergent was Use more detergent, see dispensed. "Adding detergent". The spray arms are blocked Turn the spray arm and by items. rearrange the dishes if necessary.
Frequently asked questions Problem Possible fault Solution Dishes are not dry, The rinse aid setting may be Increase the dosage, refill glasses and cutlery too low, or the rinse aid the reservoir or switch the are spotted. reservoir is empty. rinse aid product when refilling, see "Before using for the first time". Leave dishes in longer, see Dishes were taken out too soon. "Use". Set the Detergent setting for A "Tab" product was used. These products have a low a normal detergent and add drying effect.
Frequently asked questions Problem Possible fault Solution Glasses are discolored and the film cannot be wiped off. Clouding or etching on glasses. Detergent deposits. Use a different detergent. Glasses are dull and discolored, film cannot be wiped off. Tea or lipstick stains have not been completely removed. Plastics are discolored.
Comparison tests 10 place settings, Standard program: Normal Upper basket Lower basket Cutlery tray 41
After sales service Repairs MieleCare In the event of a fault which you cannot correct yourself please contact the Miele Service Department at the phone number on the back of this booklet. (USA only) ^ Please quote the model type and number of your appliance. These can be found on the data plate along the right edge of the door. PC Update The Program Correction (PC) allows a technician to update the dishwasher to make use of new technology.
Transport To transport the dishwasher, e.g. when moving to a new home, note the following: – Empty the dishwasher. – Secure any loose parts, e.g. hoses, cables, cutlery baskets. – Transport the dishwasher in the upright position. If unavoidable it may be transported on its back. Do not transport it on its side or on the door. Residual water in the machine could leak and cause electrical damage.
User Maintenance Instructions To prevent accidents and appliance damage, read these instructions before installation or use.
Cleaning and Care Exterior Check and clean your dishwasher regularly. This will help avoid problems and faults. ,Abrasive cleaning agents, all-purpose cleaners, thinner or ammonia based cleaners should not be used on the dishwasher. They will damage the surface. Wash cabinet Generally, the wash cabinet is self cleaning if the correct amount of detergent is used. ^ Only use a conditioner suitable for your kitchen cabinetry. ^ Clean wood only with a damp cloth and wipe dry.
Cleaning and Care Triple filter system The triple filter system in the base of the wash cabinet prevents food from being redeposited on dishes. It also protects the circulation pump from damage caused by foreign objects (e.g. broken glass, bones). During normal use, the filter system is self-cleaning. ,The machine must not be used without all the filters in place! ^ Check and clean the filter system periodically for any trapped or foreign objects.
Cleaning and Care To clean the inside of the filter, the flap must be opened. ^ Return the filter so it lies flat in the base of the wash cabinet. ^ Push the clips together a and open the flap b. ^ Lock the filter by turning the handle clockwise. ^ Rinse under running water. ^ Close the flap so that the clip engages. 48 ,The triple filter system must be inserted and locked into place. Large particles could get in the circulation system and cause a blockage.
Cleaning and Care Cleaning the spray arms Sometimes particles of food get stuck in the spray arm jets. The spray arms should be inspected and cleaned every 4 - 6 months. ^ Turn off the dishwasher before cleaning. Removing the spray arms ^ Remove the cutlery tray (if present). ^ Push the upper spray arm up to engage the inner ratchet and unscrew the spray arm. ^ Lift up the middle spray arm, a, to engage the ratchet and unscrew the spray arm, b. ^ Remove the lower basket.
Cleaning and Care Cleaning the water inlet filter A filter is incorporated into the intake hose attached to the dishwasher’s shut off valve. If your water is hard or the pipes contain sediment, this filter may clog and prevent enough water from entering the wash cabinet. ,The plastic housing of the water connection contains electrical wiring. Do not cut the intake hose or submerge it in liquid.
Cleaning and Care Cleaning the drain pump and non-return valve If the dishwasher is not completely drained at the end of a program, the drain pump or non-return valve may be blocked. ^ Turn off the dishwasher and pull the plug. ^ Remove the triple filter (see "Triple filter system"). ^ Use a cup or bowl to scoop water out of the wash cabinet. The drain pump is beneath the non-return valve (see arrow). ^ Remove all foreign objects from the drain pump (glass or bone splinters).
Installation Instructions Please refer to the Installation Diagram supplied with these instructions. To comply with IEC sound testing protocols, please contact Miele for additional instructions. Information is subject to change. Please refer to our website to obtain the most current product specification, technical & warranty information.
Help to protect the environment Disposal of the packing material The cardboard box and packaging protect the appliance during shipping. These materials are biodegradable and recyclable. Please recycle. Ensure that any plastic wrappings, bags etc. are disposed of safely and kept out of the reach of children. Danger of suffocation! 54 Disposal of an old machine Old appliances may contain materials that can be recycled.
Electrical connection ,Installation, repairs and other work by unqualified persons could be dangerous. Check that the voltage, frequency and fuse rating shown on the data plate match the household mains supply. The power outlet must be accessible after installation. Do not use an extension cord to connect the dishwasher to the mains. Danger of overheating! See data plate on the right side of the door. A damaged power cord must only be replaced with a genuine Miele cord by a Miele service technician.
Plumbing Waterproof system All Miele dishwashers have a safety valve located on the incoming water line and a sealed underside with a water sensor. If a fault occurs, the water intake is stopped and the drain pump is activated. ,To prevent damage to the dishwasher, it must only be connected to a fully vented drainage system. Connection to the water supply ,Do not drink water from the dishwasher! – The dishwasher can heat its own water to the temperature required by the wash program.
Plumbing Drainage Venting the drainage system – The machine comes equipped with a built-in non-return valve on the discharge side to prevent waste water from flowing back into the dishwasher. If the dishwasher drain hose is connected to a floor drain or to a drain pipe that is less than 8" (20 cm) above the floor, the drain must be vented. Otherwise the water inside the dishwasher may siphon out during the wash program. – The dishwasher is equipped with a 5 ft (1.
Alteration rights reserved / 1711 G1202 M.-Nr. 07 768 740 / 04 INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.