Operating Instructions Dishwasher G 4281 G 4286 To prevent accidents and appliance damage read these instructions before installation or use. en - US, CA M.-Nr.
Contents IMPORTANT SAFETY INSTRUCTIONS . . . . . . . 4 Guide to the dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Energy saving washing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents Additional options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Turbo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Delay start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Buzzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IMPORTANT SAFETY INSTRUCTIONS WARNING – When using your dishwasher, follow basic precautions, including the following: Read the operating instructions and installation diagram carefully before installation or use of the dishwasher to prevent injury and machine damage. Use the dishwasher only for its intended purpose. This appliance is intended for residential use only. Keep these operating instructions in a safe place and pass them on to any future user.
IMPORTANT SAFETY INSTRUCTIONS Installation ~ The dishwasher must be installed and connected in accordance with the installation instructions. ~ Installation and repair work should be performed by a Miele authorized service technician. Work by unqualified persons could be dangerous and may void the warranty. ~ Do not install or use a damaged dishwasher. A damaged appliance is dangerous. Unplug the machine and contact Miele Technical Service Department. ~ Ensure that any plastic wrappings, bags, etc.
IMPORTANT SAFETY INSTRUCTIONS Use ~ To reduce the risk of injury, do not allow children to play in, on or near the dishwasher. It is possible for small fingers may be pinched in the door. ~ Only use the dishwasher if all panels are properly in place. ~ Do not tamper with the controls. ~ Do not sit or stand on the door or baskets of the dishwasher. Close the door when not in use. ~ Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for two weeks or more.
Guide to the dishwasher a Upper spray arm (not visible) g Triple filter system b Cutlery tray h Data plate c Upper basket i Rinse aid reservoir d Middle spray arm j Dual compartment detergent dispenser e Air inlet for drying (depending on model) f Lower spray arm 7
Guide to the dishwasher Control panel a Check / Refill indicators e Program selection b Time display f Program button c , button with indicator light (Delay start) g K button (On/Off) with indicator light d Turbo button with indicator light This operating instruction manual describes several dishwasher models with different indicated settings. The different dishwasher models are named : Standard = Dishwasher with 31 11/16" (80.5 cm) height (built-in) or 33 1/4" (84.
Caring for the environment Energy saving washing This dishwasher is economical in the use of water and electricity. For best results follow these tips: ^ For lowest energy consumption you may connect the dishwasher to a cold water source. ^ Make full use of the baskets' capacity without overloading the dishwasher. This ensures the most economical washing. ^ Choose a program that best suits the degree of soiling and the type of dishes being washed. ^ Use the Economy program for energy saving dishwashing.
Before using for the first time To open the door To close the door ^ Push the baskets in. ^ Lift the door and push until it clicks into position. ^ Pull the handle to open the door. If the door is opened during operation, the dishwasher will stop running. Once the door is closed the program will continue.
Before using for the first time Rinse aid Rinse aid is needed to prevent spotting on dishes and glassware. The rinse aid is filled in the reservoir and the set amount will be automatically dosed. ,Filling the rinse aid reservoir with detergent will damage the reservoir. Only pour rinse aid formulated for residential dishwashers into the reservoir. When using "Tab" detergents rinse aid is not needed.
Before using for the first time Deactivating refill indicators If you consistently use Tab detergents, you can deactivate the refill indicator if you wish. ^ Press the K button to turn the dishwasher off. ^ Hold down the Program button and simultaneously turn the dishwasher on using the K button. Keep the Program button pressed for at least four seconds until the lower right program indicator lights up. If it does not come on, start over. ^ Press the Turbo button nine times.
Before using for the first time Setting the rinse aid dosage You can adjust the rinse aid dosage to optimize the results. The rinse aid dosage can be set at levels between 0 and 6 ml. The factory setting is 3 ml of rinse aid. This is just a recommendation. If the dishes are spotty: ^ Use a higher setting. If the dishes are cloudy or streaky: ^ Use a lower setting. ^ Press the K button to turn the dishwasher off. ^ Hold down the Program button and simultaneously turn the dishwasher on using the K button.
Loading the dishwasher ,Do not wash items soiled with ash, sand, wax, grease or paint in the dishwasher. Ash and sand do not dissolve and will be distributed throughout the inside of the dishwasher. Wax, grease and paint will cause permanent discoloration and damage to the dishwasher. ^ Scrape food from dishes before placing them in the dishwasher, rinsing is not necessary. ^ Some foods contain natural dyes, e.g. carrots or tomatoes.
Loading the dishwasher Items not recommended for dishwashing – Cutlery with wooden handles – Wooden cutting boards – Glued items such as old knives with handles glued together around the shank of the blade – Handmade craft items, antique, metal trimmed or decorative glassware Glassware: – There are no standard guidelines for washing glassware, when in doubt wash by hand. – When purchasing new dishes, glasses and cutlery, make sure they are dishwasher safe.
Loading the dishwasher Typical load for 10 place settings with cutlery tray Upper basket Cutlery tray 16 Lower basket
Loading the dishwasher Typical load for 16 place settings with cutlery tray Upper basket Lower basket Cutlery tray 17
Loading the dishwasher Upper basket ,Always use the dishwasher with the upper and lower basket in place. Adjustable cup rack (depending on model) ^ Raise the rack to make room for tall glasses. Glasses can also be leaned against the cup rack so they are more stable. ^ Lower it to double stack smaller pieces. ^ Load the upper basket with small, lightweight, or delicate items such as cups, saucers, glasses, dessert bowls and flat pans.
Loading the dishwasher Adjusting the upper basket To adjust the upper basket downwards: In order to gain more space for taller items the upper basket can be adjusted on three levels with 2 cm between each level. ^ Pull up on the levers at the sides of the upper basket. The upper basket can also be set at an angle with one side high and the other side low. Make sure, however, that the basket can slide smoothly in and out of the cabinet. ^ Slide out the upper basket.
Loading the dishwasher Lower basket Heavily soiled items ^ Place larger and heavier items such as plates, serving platters, saucepans, bowls, etc. in the lower basket. It can also be used for glasses, cups, small plates and saucers. Dishwasher with cutlery tray ^ Place very large plates in the centre of the lower basket. Dishwasher with cutlery basket When tilted, plates up to 35 cm in diameter can be accommodated.
Loading the dishwasher Cutlery tray (depending on model) ^ Arrange the cutlery as shown in the cutlery tray. Spoons with thick handles may have to be placed as knives and forks with their heads in the holders. For easier unloading cutlery should be grouped in zones, one for knives, one for forks, one for spoons, etc. Place knives with the cutting edge down and forks with the prongs between the holders.
Loading the dishwasher Cutlery basket (depending on model) Cutlery insert for the cutlery basket The cutlery basket can be placed anywhere on the front rows of spikes in the lower basket. ^ To avoid risk of injury, knives and forks should be placed with the handles upwards in the basket. However, cutlery placed handle down in the basket will come out cleaner and drier. ^ Place small items of cutlery in the individual slots on three sides of the cutlery basket.
Optional accessories Optional dishwasher accessories are available from your Miele dealer, Miele or Mieleusa.com (depending on your model some may already be supplied with your machine as standard). If you would like to... the following accessory will need to be ordered... ...wash a Miele Cappuccinatore ... a Cappuccinatore insert for the upper basket. ...wash additional items of cutlery ... a cutlery basket for the lower basket. ...wash long-stemmed glassware ...
Use Detergent ,Dishwasher detergents contain irritant and corrosive ingredients. Avoid inhaling or swallowing dishwasher detergent. Keep children away from detergent. Keep detergent out of the reach of children. Keep children away from the dishwasher when the door is open. There could still be detergent residues in the dishwasher. Only add detergent just before starting the program and lock the door with the child safety lock (depending on model). ,Only use detergents formulated for domestic dishwashers.
Use Adding detergent ^ Press the latch on the detergent dispenser. The flap will spring open. The flap is always open at the end of a program. ^ Add detergent to the compartments and close the container flap. ^ Use one tab or add powder or gel detergent to compartment II and close the flap. ^ If a Pre-rinse is desired, and available for your chosen program, add 1 teaspoon (5 ml) of detergent to compartment I. Compartment I holds a maximum of 2 teaspoons (10 ml), compartment II holds a maximum of 3.
Use Turning the dishwasher on Starting a program ^ Open the water supply if it is closed. ^ Close the door to start the program. ^ Open the door. ^ Make sure the spray arms can rotate freely. ^ Press the K button to turn the dishwasher on. The K indicator light and the program indicator light come on. Selecting a program Choose the program according to the type of dishware and soiling. See "Program guide" for a description of the programs and their applications.
Use Program guide When to use Program sequence Pre-rinse 1 2 Interim rinse 1 2 Final Drying rinse X X X X X X X X For normally soiled dishware, energy saving program with a long soaking time and a low temperature X X X X SaniWash To sanitize dishware, e.g. baby bottles, cutting boards and preparation dishware. X X X Rinse & Hold To rinse dishes when a complete program is not needed.
Use Time display Standby Before the program starts, the time display shows the time of the selected program in hours and minutes. The remaining time is displayed during the program. A few minutes after the last button is pressed or a few minutes after the end of the program the dishwasher will switch to Standby mode to save energy. The time display and the indicator lights are turned off and only the K indicator light flashes slowly. The time that is displayed may vary for the same program.
Use At the end of a program ^ Open the door slightly to check whether the program has finished. The program has ended if the time display shows a 0. The program has not yet finished as long as the program indicator light is still flashing. Close the door again so that the program runs to the end. Dishes tends to chip if removed still hot from the dishwasher. Let the dishware cool.
Use Interrupting a program A program will be interrupted as soon as the door is opened. When the door is closed again, the program will continue from where it was interrupted. ,Open the door with care. The water in the dishwasher is hot. Danger of scalding. Before closing the door again, leave it ajar for approx. 20 secs. This will enable the temperature in the wash cabinet to settle. Close the door firmly until it clicks into place.
Additional options Turbo Delay start The Turbo function reduces the program runtimes in programs where the option is available. The start time of a program can be delayed. The start time can be delayed from 30 minutes to 24 hours. The delay is set in 30 minute increments. Energy consumption will increase to achieve optimum results. ^ Open the door. ^ Press the K button to turn the dishwasher on. The K indicator light comes on. ^ Select the desired program. ^ Press the Turbo button.
Additional options ^ Open the door. ^ Press the K button to turn the dishwasher on. The K indicator light comes on. Delay start time shown in the time display: up to 59 minutes: e.g. 30 minutes = 30 ^ Use the Program button to select the desired program. 1 hour to 9 hours 30 minutes: e.g. 5 hours = 5.00 ^ Press the , button. more than 10 hours: e.g. 15 hours = 15^ The last Delay start time will appear in the time display. The , indicator light comes on.
Additional options Buzzer ^ Press the Turbo button four times. A buzzer sounds at the end of a program and when a fault occurs. The Turbo indicator light shows 4 short flashes in intervals. The buzzer at the end of a program sounds four times in intervals with a short pause. The flashing in the time display shows whether the program end buzzer is turned on or off: The fault buzzer sounds four times in an interval without pausing. – "p 1": buzzer is on The buzzer is activated by default.
Additional options Memory The memory function allows you to save the last selected program. If you turn the dishwasher off and on again after a program has finished, the last selected program is displayed instead of the Economy program. The flashing in the time display shows whether Memory is turned on. – "p 1": Memory is on. – "p 0": Memory is off. ^ Press the Program button if you wish to change the setting. ^ Open the door. The setting is immediately saved.
Additional options Optimize Standby ^ Open the door. A few minutes after the last button is pressed or a few minutes after the end of the program the dishwasher will switch to Standby mode to save energy. The time display and the indicator lights are turned off and only the K indicator light flashes slowly. ^ Press the K button to turn the dishwasher off. If the dishwasher is not turned off after the program ends, after a few minutes in Standby mode it will turn off completely.
Additional options Factory defaults If you have changed any settings, you can reset them to the factory defaults. ^ Open the door. ^ Press the K button to turn the dishwasher off. ^ Press and hold the Program button and simultaneously turn the dishwasher on using the K button. Keep the Program button pressed for at least four seconds until the lower right program indicator lights up. If it does not come on, start over. ^ Press the Turbo button 12 times.
Frequently Asked Questions ,Repairs should only be carried out by a qualified and trained person in accordance with local and national safety regulations. Unauthorized repairs could cause personal injury or machine damage. Technical faults Problem Possible fault The dishwasher will The door is not properly not start. closed. The dishwasher is not plugged in. The circuit breaker has tripped. The dishwasher stops during a program. Solution Push the door firmly closed. Insert the plug.
Frequently Asked Questions Faults in the water intake or water drain Problem Possible fault Solution The dishwasher The water supply stops shortly after is closed. the program starts. The buzzer sounds. The Intake/Drain indicator light alternates between flashing and remaining steady when the door is open. – Open the water supply all the way. The dishwasher has stopped. The buzzer sounds. The Intake/Drain Fault F12/F13: indicator light Water intake fault. flashes when the door is open.
Frequently Asked Questions General problems with the dishwasher Problem The indicator lights and the time display are dark. Only the indicator light K flashes slowly. Possible fault Solution The indicator lights and the time display turn off automatically to save energy (Standby). Press the K button to come out of Standby mode. There are detergent residues in the dispenser at the end of a program. The detergent dispenser flap cannot be closed properly.
Frequently Asked Questions Noises Problem There is a knocking noise in the wash cabinet. There is a rattling noise in the wash cabinet. There is a knocking noise from the water pipe 40 Possible fault A spray arm is hitting the dishware. Dishware is moving around in the wash cabinet. A foreign object has become lodged in the drain pump. Solution Interrupt the program and rearrange items blocking the spray arms. Interrupt the program and rearrange loose pieces.
Frequently Asked Questions Poor cleaning results Problem The dishes are not clean. Possible fault The dishes were not loaded correctly. The program was not intensive enough. Not enough detergent was dispensed. The spray arms are blocked by dishware. The triple filter in the wash cabinet is clogged or not correctly inserted. The spray arm jets might be clogged as a result. The non-return valve is stuck in the open position. Dirty wash water will run back into the wash cabinet.
Frequently Asked Questions Problem Possible fault Dishes are not dry, The rinse aid dosage is set orglasses and too low or the rinse aid cutlery are spotty. reservoir is empty. White residue is visible on the dishware. Clouding occurs on glassware and cutlery; the deposit can be wiped off. 42 Dishes were taken out too soon. You used a multi-function detergent with too little drying power. The rinse aid dosage is too low. You used an unsuitable multi-function detergent.
Frequently Asked Questions Problem Possible fault Solution Glasses have a brownish-blue discoloration; the deposit cannot be wiped off. Detergent deposits. Switch to another detergent right away. Glasses are dull and discolored; the deposit cannot be wiped off. Tea or lipstick stains have not been completely removed. The glasses are not dishwasher-safe. Surface changes occur. There is no remedy. Use only dishwasher safe glasses. The wash temperature of the selected program was too low.
After sales service Repairs MieleCare In the event of a fault which you cannot correct yourself please contact the Miele Service Department at the phone number on the back of this booklet. (USA only) ^ Please quote the model type and number of your appliance. These can be found on the data plate along the right edge of the door. PC Update The Program Correction (PC) allows a technician to update the dishwasher to make use of new technology.
User Maintenance Instructions To prevent accidents and machine damage, read these instructions before installation or use.
Cleaning and Care Exterior Check and clean your dishwasher regularly. This will help avoid faults and problems. ,Abrasive cleaning agents, all-purpose cleaners, thinner or ammonium cleaners should not be used on the dishwasher. They will damage the surface. Wash cabinet Generally, the wash cabinet is self cleaning if the correct amount of detergent is used. ^ Only use a conditioner suitable for your kitchen cabinetry. ^ Clean wood with a damp cloth and wipe dry.
Cleaning and Care Triple filter system The triple filter system in the base of the wash cabinet prevents food from being redeposited on dishes. It also protects the circulation pump from damage caused by foreign objects (e.g. broken glass, bones). During normal use, the filter system is self-cleaning. ,The machine must not be used without all the filters in place! ^ Check and clean the filter system periodically for any trapped or foreign objects.
Cleaning and Care To clean the inside of the filter, the flap must be opened. ^ Return the filter so it lies flat in the base of the wash cabinet. ^ Push the clips together a and open the flap b. ^ Lock the filter by turning the handle clockwise. ^ Rinse under running water. ^ Close the flap so that the clip engages. 48 ,The triple filter system must be inserted and locked into place. Large particles could get in the circulation system and cause a blockage.
Cleaning and Care Cleaning the spray arms Sometimes particles of food get stuck in the spray arm jets. The spray arms should be inspected and cleaned every 4 - 6 months. ^ Turn off the dishwasher before cleaning. Removing the spray arms ^ Remove the cutlery tray (if present). ^ Push the upper spray arm up to engage the inner ratchet and unscrew the spray arm. ^ Lift up the middle spray arm, a, to engage the ratchet and unscrew the spray arm, b. ^ Remove the lower basket.
Cleaning and Care Cleaning the drain pump and non-return valve If the dishwasher is not completely drained at the end of a program, the drain pump or non-return valve may be blocked. ^ Turn off the dishwasher and pull the plug. ^ Remove the triple filter (see "Triple filter system"). ^ Use a cup or bowl to scoop water out of the wash cabinet. The drain pump is beneath the non-return valve (see arrow). ^ Remove all foreign objects from the drain pump (glass or bone splinters).
Installation Instructions Please refer to the Installation Diagram supplied with these instructions. Information is subject to change. Please refer to our website to obtain the most current product specification, technical & warranty information.
Electrical connection ,Installation, repairs and other work by unqualified persons could be dangerous. Check that the voltage, frequency and fuse rating shown on the data plate match the household mains supply. The power outlet must be accessible after installation. Do not use an extension cord to connect the dishwasher to the mains. Danger of overheating! See data plate on the right side of the door. A damaged power cord must only be replaced with a genuine Miele cord by a Miele service technician.
Electrical connection Hardwired electrical connection It is possible to hardwire this appliance to an existing power cable. ,CAUTION: Before servicing, disconnect the power supply by either removing the fuse, shutting off the power main or manually "tripping" the circuit breaker. Installation work and repairs should only be performed by a qualified technician in accordance with all applicable codes and standards.
Plumbing Connection to the water supply ,Installation, repairs and other work by unqualified persons could be dangerous. ,Do not drink water from the dishwasher! – The dishwasher can heat its own water to the temperature required by the wash program. This allows for connection of the machine to either a hot (max. 140°F / 60°C) or cold water source. For lowest energy consumption you may connect the dishwasher to a cold water source.
Plumbing Drainage – The machine comes equipped with a built-in non-return valve on the discharge side to prevent waste water from flowing back into the dishwasher. – The dishwasher is equipped with a 5 ft (1.5 m) flexible drain hose with an internal diameter of 7/8" (22 mm). – Drain hose extensions and adapters can be ordered from Miele. The maximum drain hose length is 13 ft. (4 m), max. drain height: 39" (1 m).
Noise measurement General requirements for measuring noise The dishwasher must be loaded with 16 place settings and the Normal program must be used. Installation requirements for measuring noise The dishwasher must be installed as follows:. ^ Install the dishwasher into an appropriate housing unit. ^ Secure the front panel.
Noise measurement ^ Push the insulation mat supplied (depending on model) under the plinth until it is up against the appliance feet a. ^ Attach the toe-kick so that it is flush with the door front b.
Alteration rights reserved / 0313 G4281/G4286 / M.-Nr. 09 510 201 / 01 INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.
