Operating instructions for dishwashers To avoid the risk of accidents or damage to the appliance, it is essential to read these instructions as well as the installation plan before it is installed and used for the first time. en - GB M.-Nr.
Contents Guide to the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Appliance overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Miele{home . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents Cutlery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 3D cutlery tray (depending on model) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Cutlery basket (depending on model) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Detergent . . . . . . . . . . . . . . . . . . . .
Contents Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Cleaning the water inlet filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Cleaning the drain pump and non-return valve . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 After sales service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 Repairs . . . . . . . . . . . . . . . . . .
Guide to the appliance Appliance overview a Upper spray arm (not visible) g Filter combination b Cutlery tray (depending on model) h Data plate c Upper basket i In-operation indicator light d Middle spray arm j Rinse aid reservoir e Air inlet for drying (depending on model) k Dual compartment detergent dispenser f Lower spray arm l Salt reservoir 5
Guide to the appliance Control panel a Selector buttons For selecting the option displayed next to them. For altering the values displayed (+/-). For scrolling to other menus. b Display See next page for more information. c Clear button U For returning to the previous menu or deleting values which have been set previously. d Delay start button , with indicator light For selecting the delay start function. e Information button : For displaying additional information about the option being displayed.
Miele{home a Communication enabled appliances Possible connections (optional) b Communication module g PC, Notebook c SuperVision master appliance h iPod* or iPhone* d Power supply i Connection with a domestic bus system display e Miele|home Gateway f (WLAN) Router j Possible internet connection * iPod und iPhone are registered trade marks of Apple Inc.
Miele{home Depending on country, this appliance is communication enabled and can be linked into the Miele|home system via a communication module b (optional accessory). Miele|home enabled appliances send information via the household power supply network d to the master appliance c / e about the operational status of the appliances, as well as information about the progress of the programme.
Warning and Safety instructions This appliance conforms to current safety requirements. Inappropriate use can, however, lead to personal injury and damage to property. To avoid the risk of accidents and damage to the appliance, please read these instructions carefully before using it for the first time. They contain important information on its safety, use and maintenance. Keep these instructions in a safe place and pass them on to any future owner.
Warning and Safety instructions Safety with children ~ Children under 8 years of age must be kept away from the appliance unless they are constantly supervised. ~ Children 8 years and older may only use the dishwasher if they have been shown how to use it in a safe way and understand the hazards involved. ~ Children must not be allowed to clean or maintain the appliance unsupervised. ~ Keep very young children away from it at all times and supervise them whilst you are using it.
Warning and Safety instructions Technical safety ~ Before setting up the appliance, check it for any externally visible damage. Under no circumstances should you use a damaged appliance. It could be dangerous. ~ The dishwasher must only be plugged into the electricity supply via a suitable switched socket. The electrical socket must be easily accessible after the dishwasher is installed so that it can be disconnected from the electricity supply at any time. (See "Electrical connection").
Warning and Safety instructions ~ Before connecting the appliance, check that the connection data on the data plate (voltage and frequency) match the mains electricity supply. If in any doubt, consult a qualified electrician. ~ The electrical safety of this appliance can only be guaranteed if correctly earthed.
Warning and Safety instructions ~ The plastic housing of the water connection contains an electrical component. The housing must not be dipped in water. ~ There are electrical wires in the water inlet hose. Do not cut the water inlet hose, even if it is too long. ~ The integrated Waterproof System offers protection from water damage, provided the following conditions are met: – The dishwasher is correctly installed and plumbed in.
Warning and Safety instructions ~ Unauthorised repairs could result in unforeseen dangers for the user, for which Miele cannot accept liability. Repairs should only be undertaken by a Miele approved service technician, otherwise any subsequent damage will not be covered by the guarantee. ~ Faulty components must only be replaced by genuine Miele original spare parts. Only when these parts are fitted can Miele guarantee the safety standards of the appliance.
Warning and Safety instructions Correct installation ~ The dishwasher must be installed and connected in compliance with the diagram supplied. ~ Take care, both before and during installation of the dishwasher, not to cut yourself on the metal parts. Danger of injury. Wear protective gloves. ~ The dishwasher must be correctly aligned to ensure problem-free operation.
Warning and Safety instructions Correct use ~ Do not use solvents in the dishwasher. Danger of explosion. ~ Do not inhale or ingest dishwasher detergent. Dishwasher detergents contain irritant or corrosive ingredients which can cause burning in the nose, mouth and throat if swallowed, or inhibit breathing. Seek medical attention immediately if detergent has been swallowed or inhaled. ~ Avoid leaving the door open unnecessarily, as you could trip over it.
Warning and Safety instructions ~ Do not fill the rinse aid reservoir with powder or liquid detergent. This will cause serious damage to the reservoir. ~ Do not fill the salt reservoir with powder or liquid dishwasher detergent. This will damage the water softener.
Warning and Safety instructions Accessories ~ Only use genuine Miele original spare parts and accessories with this dishwasher. Using spare parts or accessories from other manufacturers will invalidate the guarantee, and Miele cannot accept liability. Disposal of your old dishwasher ~ Make the door lock inoperative so that children cannot accidentally shut themselves in. Make appropriate arrangements for the disposal of the appliance.
Caring for our environment Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal and should be recycled. Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of babies and young children. Danger of suffocation.
Caring for our environment Energy saving dishwashing This dishwasher is exceptionally economical in its use of water and electricity. You can make the most of your appliance by following these tips: ^ For most economical dishwashing make full use of the baskets without overloading the dishwasher. ^ Choose the programme to suit the type of crockery being washed and the degree of soiling. ^ Select the ECO programme for energy-saving dishwashing.
Before using for the first time To open the door To close the door ^ Push the baskets right in. ^ Then raise the door up and push until the catch engages. The door will then close automatically. ,Do not put your hand inside the door as it is closing. Danger of injury. At the end of programmes with a drying phase (see "Programme chart"), the door will open automatically a little in order to help the drying process. This function can be deactivated, if preferred (see "Settings menu, AutoOpen").
Before using for the first time Display The display is used to select the following: the programme extras the delay start time the Settings menu ! information – – – – – During a programme, the display shows the following (when the door is opened): – – – – the name of the programme the current time of day the stage the programme is at the estimated time left for the programme to run – any relevant fault messages and notes To save energy, the dishwasher switches off after a few minutes if you do not press
Before using for the first time Basic settings Welcome screen ^ Switch the dishwasher on with the On/Off button K. If the dishwasher is being switched on for the first time, the welcome screen will appear after a few seconds. Language The display will then change automatically to the screen for setting the language. } #eština } dansk Language F e ^ Select the language you want and confirm this with OK. A tick ( will appear next to the language that has been set.
Before using for the first time Time The display will then change to the screen for setting the time. 12 : 00 } + } - Please set the time OK } ^ Set the hours with +/- and confirm with OK. Then set and confirm the minutes. Water hardness The display will then change to the screen for setting the water hardness. } 15°d B Water hardness } 16°d e OK } – The dishwasher must be programmed for the water hardness in your area.
Before using for the first time The dishwasher is programmed at the factory for a water hardness level of 2.7 mmol/l (15 °d - German scale). ^ Select the water hardness you want, and confirm your selection with OK. See "Programming the water hardness level" for further information. These settings will be saved in memory after the dishwasher has been through one complete programme. Finally, two messages will appear in the display.
Before using for the first time Water softener In order to achieve good cleaning results, the dishwasher needs to operate with soft water. Hard water results in the build-up of calcium deposits on crockery and in the dishwasher. Mains water with a hardness level higher than 0.7 mmol/l (4 °d – German scale) needs to be softened. This takes place automatically in the integrated water softener. The water softener in this dishwasher is suitable for a water hardness level of up to 12.
Before using for the first time Programming the water hardness level ^ Switch the dishwasher on with the On/Off button K, if it is switched off. The main menu will appear in the display. If the memory function is activated, the programme menu for the programme last selected will be displayed instead (see "Settings menu !, Memory"). If this is the case, press the Clear button U to switch to the main menu. ^ In the "Settings menu !" select the Water hardness option.
Before using for the first time Before using the appliance for the first time, you require: – approx. 1 kg dishwasher salt*, – domestic dishwasher detergent*, – rinse aid* formulated for domestic dishwashers. * See "Optional accessories" Every dishwasher is tested at the factory. There will be residual water in the appliance from this test. It is not an indication that it has been used previously. Filling the salt reservoir If the water in your area is very soft and constantly lower than 0.
Before using for the first time ^ When filling the salt reservoir only open the door halfway to ensure that all the salt gets into the reservoir. ^ Press the button on the lid of the salt reservoir in the direction of the arrow until the flap springs open. Do not fill the salt reservoir with water. ^ Add salt only until the reservoir is full or until water runs out of the opening. The salt reservoir holds approx. 1 kg of salt, depending on the brand used. Do not add any more than 1 kg of salt.
Before using for the first time Salt indicator ^ Fill the salt reservoir with dishwasher salt for reactivation when the F Insufficient salt message appears. (If it appears during a programme, wait until the end of the programme). ^ Confirm with OK. The "Insufficient salt" message will go out. After the salt reservoir has been filled, the "Insufficient salt" message may still appear in the display if the salt concentration has not yet reached the correct level. If this is the case, confirm again with OK.
Before using for the first time Rinse aid Adding rinsing agent Rinse aid is necessary to ensure water does not cling and leave marks on crockery during the drying phase and helps crockery dry faster after it has been washed. Rinse aid is poured into the storage reservoir and the amount set is dispensed automatically. ,Inadvertently filling the rinse aid reservoir with powder or liquid detergent will always cause serious damage to the reservoir.
Before using for the first time "Rinse aid low" message When the ( Rinse aid low message appears, the reservoir contains sufficient rinse aid for 2-3 programmes only. ^ Add rinse aid in plenty of time. ^ Confirm with OK. The "Rinse aid low" message will go out. ^ Add rinse aid only until it is visible in the opening. If you only ever use combination products containing salt and rinse aid in your dishwasher, you can switch the messages off if you wish (see "Settings menu - Refill display").
Loading the dishwasher Note Remove coarse food residues from crockery. There is no need to rinse items under running water. ,Do not wash items soiled with ash, sand, wax, lubricating grease or paint in the dishwasher. These substances will damage the dishwasher. Crockery can be loaded anywhere in the baskets, but the following notes should be observed: – Do not place crockery and cutlery inside other pieces where they may be concealed. – Load the crockery so that water can access all surfaces.
Loading the dishwasher Items not suitable for dishwashers: – Wooden cutlery and crockery or items with wooden parts: these may discolour and fade. The glue used in these items is not dishwasher-proof and wooden handles may come loose after being washed in a dishwasher. – Craft items, antiques, valuable vases and decorative glassware are also not suitable for dishwashers. – Plastic items which are not heat resistant: the high temperatures in the dishwasher may cause them to melt or lose shape.
Loading the dishwasher Upper basket ,For safety reasons, do not operate the dishwasher without the upper and lower baskets in place (except when running the Tall items 65 °C programme, if available). Hinged spikes The rows of spikes can be lowered to make more room for larger items such as casserole dishes. ^ Press the yellow lever downwards a, and then lower the spikes b. ^ Use the upper basket for small, lightweight and delicate items such as cups, saucers, glasses, dessert bowls, etc.
Loading the dishwasher Jumbo cup rack (depending on model) The cup rack can be set at two different widths so that it can also accommodate large cups. ^ You can also move one of the side inserts of the cutlery tray to make more room for tall glasses. Adjusting the height You can set the glass rail at two different heights. ^ Pull the cup rack upwards and click it back into position at the required width. Glass rail ^ Pull the rail upwards and click it back into position at the required height.
Loading the dishwasher Adjusting the upper basket In order to gain more space for taller pieces of crockery in the lower or upper basket, the upper basket can be adjusted on three levels with 2 cm between each level. The upper basket can also be set at an angle with one side high and the other side low. This can be useful to help prevent water being left in deep dishes etc. Ensure, however, that the basket can slide smoothly in and out of the cabinet. It is better to adjust the basket before loading it.
Loading the dishwasher Lower basket ^ For larger and heavier items such as plates, serving platters, saucepans, bowls, etc. Glasses, cups and small items such as saucers can also be placed in the lower basket. Do not place thin, delicate glassware in the lower basket. ^ Place large platters and dishes in the centre of the lower basket. When tilted, plates up to 35 cm in diameter can be accommodated.
Loading the dishwasher Removable MultiComfort insert Glass rack The rear section of the lower basket is used for washing cups, glasses, plates, pots and pans. ^ The glass rack can be raised to make more room for tall items. You can remove the Multi-Comfort insert to make more room for larger items such as casserole dishes. ^ Stem glassware, e.g. wine glasses or champagne flutes, can be leaned against the glass rack or suspended from it. The height of the glass rack is adjustable.
Loading the dishwasher Glass rail This rail is designed to hold tall glasses and glasses with stems securely. ^ Press the yellow lever downwards a, and then lower the spikes b. Bottle holder ^ Lower the rail and lean tall glasses against it. Hinged spikes The bottle holder can be used to wash narrow items, e.g. milk and baby bottles. The spikes at the front are used for washing plates, soup bowls, platters, dessert bowls and saucers.
Loading the dishwasher Cutlery 3D cutlery tray (depending on model) If spoon handles do not fit between the holders, then lay them the other way round. ^ Arrange the cutlery in the tray as shown. To make unloading much easier, cutlery should be grouped in zones, one for knives, one for forks, one for spoons, etc. Spoon heads should be placed in contact with at least one of the serrated retainers on the base of the cutlery tray to ensure that water runs off them freely.
Loading the dishwasher Cutlery basket (depending on model) The cutlery basket can be placed anywhere on the front rows of spikes in the lower basket. ^ Fit it onto the cutlery basket if required. ^ To avoid the risk of injury, knives and forks should be placed with the handles upwards in the basket. However, cutlery placed handle down in the basket will come out cleaner and drier. ^ Place small items of cutlery in the individual slots on three sides of the cutlery basket.
Operation Detergent ,Only use detergents formulated for domestic dishwashers. Do not use washing-up liquid. Active ingredients Modern detergents contain various active ingredients, the most important of which are: – Phosphates to prevent calcification. – Alkalis to aid removal of dried on soiling. – Enzymes to break down starch and loosen protein. – Oxygen based bleaching agents to remove coloured stains (e.g. tea, coffee, tomato sauce).
Operation ,Avoid inhalation of powder detergents and do not ingest dishwasher detergent. Dishwasher detergents contain irritant or corrosive ingredients which can cause burning in the nose, mouth and throat if swallowed, or inhibit breathing. Consult a doctor immediately if detergent has been swallowed or inhaled. Keep detergent and other household agents out of the reach of children at all times. Keep children away from the dishwasher when the door is open.
Operation Switching on ^ Open the stopcock, if it is closed. ^ Open the door. ^ Make sure the spray arms are not obstructed. ^ Switch the dishwasher on using the On/Off button K. After a few seconds the main menu will appear in the display. If the memory function is activated, the programme menu for the programme last selected will be displayed instead (see "Settings menu !, Memory").
Operation Select an extra option(s) You can now select extra options for your chosen programme. ^ To do this, first select the Extras option in the menu. The extra options available for your programme will appear in the display. The following extra options are available: Turbo: – For shortening the programme duration. In order to achieve optimum results, consumption rates increase with this option.
Operation Starting the programme Display ^ Select the Start option. The duration of the programme selected appears in hours and minutes in the display before the programme begins. During the programme, the time left until the end of the programme is displayed. The message Please close the door will appear. If you want to select a different programme or make other changes, select Back and cancel the programme with the Cancel function. ^ Start the programme by closing the door.
Operation Standby At the end of the programme To save energy, the dishwasher will switch off a few minutes after the last time a button has been pressed or a few minutes after the end of the programme. At the end of a programme the In-operation indicator light flashes on and off slowly. It is visible even with the door closed. It will stop flashing one hour after the programme has finished. ^ Press the K button to switch the dishwasher back on again.
Operation Switching off Interrupting a programme At the end of a programme: A programme is interrupted as soon as the door is opened. If the door is closed again, the programme will continue from the point it was at before the door was opened. ^ Open the door. ^ Switch the dishwasher off using the On/Off button K. The dishwasher will continue to use energy until you switch it off with the K button. The dishwasher will switch off automatically a few minutes after the end of the programme.
Operation Changing a programme If the detergent dispenser flap has already opened, do not change the programme. If a programme has already started and you wish to change it, proceed as follows: ^ Open the door. Sensor wash 1:32 h 12:00 Cancel } Main wash ^ Select Cancel and confirm with OK. The programme will be cancelled. 12:00 Sensor wash Programme finished ^ Select Main Main menu } menu. The display will revert to the main menu. ^ Select the programme you want. ^ Select Start.
Additional functions Delay start The start time of a programme can be delayed, e.g. to benefit from economy rates of electricity. A delay start time of between 15 minutes and 24 hours can be selected. The delay start time is set in 15 minute steps. ,When using the Delay start function, make sure that the detergent compartment is dry before adding detergent. Wipe dry with a cloth if necessary.
Additional functions The display will change to show the programme menu. ^ Select Start. ^ Close the door. When the set time is reached, the programme selected will begin automatically. The , indicator light will go out. To save energy, the dishwasher will switch to Standby mode a few minutes after the last time a button has been pressed. The display and the indicator lights will go out.
Additional functions BrilliantLight DetergentAgent The dishwasher has interior lighting. When the door is open the lighting will switch off automatically after 15 minutes. For optimum cleaning results, the dishwasher automatically adjusts the programme sequence to the type of detergent being used. Depending on the programme, this can mean that the running time and energy consumption vary slightly. You can also switch off the interior lighting permanently.
Cleaning and care Check your dishwasher regularly (approx. every 4 - 6 months). This way faults and problems can be avoided. ,The external surfaces of the dishwasher are susceptible to scratching. Contact with unsuitable cleaning agents can alter or discolour the external surfaces. Cleaning the wash cabinet The wash cabinet is largely self-cleaning, provided that the correct amount of detergent is always used.
Cleaning and care Cleaning the control panel and door front To avoid damaging the external surfaces, do not use: ,Remove any soiling immediately. – cleaning agents containing soda, ammonia, acids or chlorides, If this is not done, it might become impossible to remove and could cause the external surfaces to alter or discolour. – cleaning agents containing descaling agents, ^ The control panel should only be wiped with a damp cloth.
Cleaning and care Checking the filters in the wash cabinet Cleaning the filters ^ Switch the dishwasher off. The filter combination in the base of the wash cabinet retains coarse soil from the suds solution, preventing it accessing the circulation system and re-entering the cabinet through the spray arms. ,This dishwasher must not be used without all the filters in place. Collection of coarse soil may cause the filters to clog.
Cleaning and care To clean the inside of the filter, the flap must be opened: ^ Press catches a together in the direction of the arrows as shown, and open the filter b. ^ Rinse all the filters under running water. ^ Then close the flap so that the catch engages. ^ Replace the filter combination so that it lies flat in the base of the wash cabinet. ^ Then turn the handle clockwise to lock the filter combination in place.
Cleaning and care Cleaning the spray arms ^ Remove the lower basket. Particles of food can get stuck in the spray arm jets and bearings. The spray arms should therefore be inspected and cleaned regularly (approx. every 4 - 6 months). ^ Switch the dishwasher off. Remove the spray arms as follows: ^ Take out the cutlery tray (if your dishwasher is fitted with one). ^ Push the top spray arm upwards to engage the inner ratchet. Then unscrew the spray arm.
Problem solving guide With the help of the following guide, minor faults in the performance of the appliance, some of which may result from incorrect operation, can be put right without contacting the Service Department. ,Repairs should only be carried out by a suitably qualified and trained person in strict accordance with current local and national safety regulations. Unauthorised or incorrect repairs could cause personal injury or damage to the appliance.
Problem solving guide Problem Possible cause Remedy Before rectifying the problem: – Switch the dishwasher off using the On/Off button K. The In-operation indicator is flashing quickly. The buzzer is sounding. One of the following messages appears in the display: ; Technical fault FXX There may be a technical fault. After a few seconds: – Switch the dishwasher back on. – Select the programme you want. – Close the door. If the fault message appears again, there is a technical fault.
Problem solving guide Water inlet/drain fault Problem Possible cause The In-operation indicator is flashing quickly. The buzzer is sounding. One of the following messages appears in the display: Water inlet fault Remedy The stopcock is closed. Open the stopcock fully. Water inlet fault 12/F13 Before rectifying the problem: – Switch the dishwasher off using the On/Off button K. Water intake is restricted. – Open the stopcock fully.
Problem solving guide Problem Possible cause Remedy The In-operation indicator is flashing quickly. In the display for the "Without heater" programme the following fault message appears: The intake water has – Start the programme again. not reached the – If the fault message required temperature of appears again, select a 45°C (see "Connection different programme. to the water supply"). Water intake temp. too low The In-operation indicator is flashing quickly. The buzzer is sounding.
Problem solving guide General problems Problem The display is dark. The interior lighting does not come on when the door is opened. Possible cause The dishwasher has switched off automatically to save energy. The lighting has been switched off permanently. Remedy Switch the dishwasher on again with the On/Off button K. Switch the lighting back on again (see "Additional functions, BrilliantLight"). The salt reservoir lid has – Close the salt reservoir lid not been closed properly. properly.
Problem solving guide Problem Possible cause Detergent residue is left in the dispenser at the end of a programme. The detergent dispenser lid cannot be closed properly. The dispenser was still Make sure the dispenser is damp when detergent was dry before adding added. detergent. Clogged detergent residue Clean the detergent from is blocking the catch. the catch. This is caused by the At the end of a programme there is a drying system and does film of moisture on not indicate a fault.
Problem solving guide Noises Problem Knocking noise in the wash cabinet. Possible cause A spray arm is knocking against an item in a basket. Rattling noise in the wash cabinet. Items of crockery are insecure in the wash cabinet. A foreign object (e.g. a cherry stone) has becomed lodged in the drain pump. Knocking noise in the water pipes. This may be caused by the on-site installation or the cross-section of the piping.
Problem solving guide Unsatisfactory washing result Problem Possible cause The dishes are not The dishes were not loaded clean. correctly. The programme was not powerful enough. Remedy See notes in "Loading the dishwasher". Select a more intensive programme. See Programme chart. There is some stubborn Use the Sensor wash soiling although most of the function (see "Settings crockery is only lightly soiled menu, Sensor wash"). (e.g. with tea stains). Not enough detergent was dispensed.
Problem solving guide Problem Possible cause Remedy Dishes, cutlery and The amount of rinse aid may Replenish the reservoir, glasses are not dry be insufficient, or the rinse increase the dosage or or are flecked. aid reservoir empty. change the brand of rinse aid (see "Before using for the first time: Rinse aid"). Leave it in for longer. See Crockery was taken out of the cabinet too soon. "Operation".
Problem solving guide Problem Possible cause Remedy Glassware has a brown or blue tinge, and film cannot be wiped off. Glassware is dull and discoloured; film cannot be wiped off. This may be caused by the detergent. Change your detergent. The glasses are not dishwasher-proof. The surfaces are affected. There is no remedy. Purchase glassware which is dishwasher-proof. Tea or lipstick stains The wash temperature of have not been the selected programme completely removed. was too low.
Maintenance Cleaning the water inlet filter A filter is incorporated in the screw connection of the valve on the water inlet hose. The filter must be cleaned when dirty, otherwise insufficient water flows into the wash cabinet. ,The plastic housing of the water connection contains an electrical component. It must not be dipped in water.
Maintenance Cleaning the drain pump and non-return valve If the water has not been pumped away at the end of a programme the drain pump or the non-return valve might be blocked. They are, however, easy to clean. ^ Disconnect the dishwasher from the mains supply. Switch off at the mains socket and withdraw the plug. ^ Take the filter combination out of the wash cabinet (see "Cleaning and care - Checking the filters in the wash cabinet").
After sales service Repairs Future updates In the event of any faults that you cannot remedy yourself, please contact: The programme update function is designed to enable a service technician to update your appliance's electronics in keeping with advances in technology. – Your Miele dealer, or – the Miele Service Department (see back cover for address). Please note that telephone calls may be monitored and recorded to improve our service.
Programme chart Crockery Mixed, everyday crockery Food deposits All normal food deposits Action required This needs an adaptable programme... Shorter duration... Heat-sensitive glasses and plastic This needs a short programme... Fresh, easily removed food deposits Mixed crockery This needs a gentle programme with glass care... Very quiet programme Normal food deposits which have begun to dry on To save water and energy... This needs a standard programme... Shorter duration...
Programme chart Programme Detergent Compartment I 2) Compartment II 2) – 25 ml or 1 tab Quick wash 40°C – 20 ml or 1 tab 3) Sensor wash gentle – 20 ml or 1 tab Extra quiet – 25 ml or 1 tab 3) ECO – 25 ml or 1 tab – 25 ml or 1 tab 10 ml 25 ml or 1 tab – 25 ml or 1 tab Sensor wash + Turbo Light soiling 50°C + Turbo Pots & pans 75°C + Turbo Hygiene 2) 3) see "Detergent" In some cases, tabs may not dissolve completely.
Programme chart Programme Programme sequence Pre-wash Sensor wash Quick wash 40 °C 2x Final rinse °C Drying If required X 60 X 45 X Variable programme sequence with glass care, sensor controlled adjustment according to the amount of crockery and level of food deposits If required Extra quiet 1) Light soiling 50 °C Hygiene 1x 45-65 40 Sensor wash gentle # Pots & pans 75 °C Interim rinse Variable programme sequence, sensor controlled adjustment according to the amount of crockery and lev
Programme chart Consumption 2) Electricity Duration 2) Water Cold water connection (15 °C) kWh Hot water connection (55 °C) kWh Litres Cold water connection (15 °C) h:min Hot water connection (55 °C) h:min 0.80 3)-1.25 4) 0.55 3)-0.90 4) 7.0 3)-17.0 4) 1:30-2:38 1:18-2:21 0.55 0.20 10.0 0:38 0:27 0.75 3)-1.00 4) 0.45 3)-0.55 4) 10.0 3)-17.0 4) 1:26-2:02 1:17-1:43 1.05 0.75 10.0 4:45 4:35 0.83 0.48 10.0 2:21 2:10 0.95 0.65 10.0 1:36 1:23 1.40 1.00 16.0 2:43 2:32 1.
Programme chart Programme When to use Pre-wash For rinsing crockery to avoid smells, if a complete cycle is not yet needed. Without heater ! Only for use with hot water connection of at least 45°C/115°F; for lightly to normally soiled crockery; includes sensor controlled glass care system. Intensive 65 °C For heavily soiled crockery with dried on soiling containing starch. Pasta For removing dried on pasta/paella residues; use 20% more detergent than recommended for a full load.
Programme chart Consumption 2) Programme sequence Prerinse Main wash °C Interim rinse Final rinse °C Drying X Electricity Water Hot Cold water water connec- connection tion (15 °C) (55 °C) kWh kWh Litres 0.01 0.01 4.0 0.05 26.0 Duration 2) Hot Cold water water connec- connection tion (15 °C) (55 °C) h:min h:min 0:15 0:15 2X X X X X 1:18 X 65 X 60 X 1.15 0.85 13.0 2:10 1:57 X 75 X 60 X 1.30 1.00 13.0 2:14 2:01 X 50 X 60 X 0.80 0.55 13.
Optional accessories To make the most of your dishwasher Optional accessories for particular purposes are available from your Miele dealer, from the Miele Spare Parts Department or via the internet at www.miele-shop.com (some may be supplied as standard, depending on model). If you would like to … you will need to order … ... wash a Miele Cappuccinatore … a Cappuccinatore insert for the upper basket ... wash additional items of cutlery ... a cutlery basket for the lower basket ...
Electrical connection Electrical connection U.K. ,All electrical work must be carried out by a suitably qualified and competent person, in accordance with current local and national safety regulations (BS 7671 in the UK). Ensure power is not supplied to the appliance until after installation work has been carried out. The appliance is supplied with a mains cable with moulded plug ready for connection to a 230-240V mains supply.
Plumbing The Miele waterproof anti-leak system Providing your dishwasher has been installed correctly, the Miele waterproof anti-leak system will protect you from water damage throughout its lifetime. Connection to the water supply ,Water in the dishwasher must not be used as drinking water. – The dishwasher may be connected to a cold or hot water supply, max. 60 °C. We would only recommend connection to a hot water supply if it is economical, e.g. a solar powered supply.
Plumbing – The water pressure (flow pressure at the take-off point) must be between 30 and 1000 kPa (0.3 and 10 bar). If the water pressure is lower than this, the fault message Water inlet fault will appear in the display (see Problem solving guide). If the water pressure is too high, a pressure reducer valve must be fitted. ,To avoid any damage to the appliance, the dishwasher must only be connected to a fully vented plumbing system.
Plumbing Drainage – The appliance drainage system is fitted with a non-return valve, which prevents dirty water from flowing back into the dishwasher via the drain hose. – The dishwasher is supplied with approx. 1.5 m of flexible drain hose with an internal diameter of 22 mm. – The drain hose can be extended using a connection piece to attach a further length of hose. The drainage length must not be longer than 4 m, and the delivery head must not exceed 1 m.
Technical data Dishwasher model Standard XXL Height 80.5 cm (adjustable + 6.5 cm) 84.5 cm (adjustable + 6.5 cm) Height of building-in recess Min. 80.5 cm (+ 6.5 cm) Min. 84.5 cm (+ 6.5 cm) Width 59.8 cm 59.8 cm Width of building-in recess 60 cm 60 cm Depth 57 cm 57 cm Weight Max. 56 kg Max. 62 kg Voltage 230 V 230 V Connected load 2200 W 2200 W Fuse rating 10 A 10 A Power consumption when switched off 0.40 W 0.40 W Power consumption when not switched off 5.00 W 5.
Settings menu ! Settings menu ! for changing standard settings To open the Settings ! menu ^ Switch the dishwasher on with the U button, if it is switched off. The main menu will appear in the display. If the memory function is activated, the programme menu for the programme last selected will be displayed instead (see "Memory"). If this is the case, press the Clear button U to switch to the main menu. } Settings F } Sensor wash Main menu r ^ Select the Settnigs ! option.
Settings menu ! Language J Time The display can be set to appear in one of several different languages. Select either a 24 hour or 12 hour clock, and then set the current time of day. You can select one of the languages displayed via the Language ! sub-menu. ^ Select the language you want and confirm this with OK. The flag after the word "Language" acts a guide if a language which you do not understand has already been set.
Settings menu ! Water hardness Sensor wash Your dishwasher is fitted with a water softener which you need to programme to the water hardness level in your area (see "Before using for the first time, Programming the water hardness level"). You can adjust the Sensor wash programme so that it will remove stubborn soiling in a lightly soiled load. Rinse aid You can adjust the rinse aid dosage for best results. The rinse aid dosage can be set from approx. 0-6 ml. The factory default setting is 3 ml.
Settings menu ! Optimise standby Refill display To save energy, the diswasher will switch off automatically a few minutes after the last time a button has been pressed or after the end of the programme. If you only ever use combination products containing salt and rinse aid in your dishwasher, you can switch the salt and rinse aid refill reminders off if you wish. The DetergentAgent function will not be affected by this. The Optimise standby function can be deactivated if wished.
Settings menu ! Change main menu You can change the order of the programmes in the main menu and also enter your favourite programmes into the first two programme places. } Sensor wash B } Cancel e Set position 1 Continue } ^ Use the e button to find the programme that you would like to have as your first choice in the main menu, and then select it using the button next to the programme. ^ Confirm with Continue.
Settings menu ! Save extras Buzzer You can set additional functions, e.g. Pre-wash, for individual programmes (see "Operation, Select an extra option(s)"). When the buzzer is activated, an audible tone sounds at the end of a programme and when there is a fault. You can use the Save extras option to save settings you have chosen for a particular programme so that they are automatically selected when you run the programme in the future.
Settings menu ! Keypad tone Memory An audible tone sounds each time a button is pressed. You can use the Memory function to save the last programme selected. There are seventeen different volume settings. Instead of the main menu, the last programme selected will appear in the display when the dishwasher is switched off and back on again or the door is opened and then closed at the end of a programme. ^ Select the volume you want and confirm this with OK.
Settings menu ! Showroom programme This programme is for demonstration use only. To switch Demo mode on ^ Select the option you want and confirm this with OK. The Demo ^ Confirm the questions which follow with OK. demonstrate operation and functions. ^ If necessary, press any button to start the Demo mode you have selected. mode and Demo mode in continuous loop programmes – – Demo mode: This programme is started by pressing any button. It will run through once and then has to be started again.
Alteration rights reserved/ G5980/G5985 / 2812 M.-Nr.