Operating and Installation Instructions Fridge-Freezer Combination KF 1801 Vi KF 1811 Vi KF 1901 Vi KF 1911 Vi To prevent accidents and machine damage read these instructions before installation or use. en - US, CA M.-Nr.
Contents IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Guide to the Fridge-Freezer combination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Before use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Turning the appliance On/Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents Changing the light bulb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Water filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Exchanging the water filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Filter Performance Data Sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Frequently asked questions . . . . . .
IMPORTANT SAFETY INSTRUCTIONS When using the appliance, follow basic safety precautions, including the following: Read all instructions before installation and use to prevent accidents and machine damage. This appliance is intended for residential use only. Use only as described in this Operating manual. Only use the appliance for its intended purpose. The manufacturer cannot be held responsible for damages caused by improper use of this appliance. This appliance complies with current safety requirements.
IMPORTANT SAFETY INSTRUCTIONS Installation This appliance is top-heavy and must be secured to prevent the possibility of tipping forward. Keep the doors closed until the appliance is completely installed and secured per the installation instructions. ~ This appliance must be installed and connected in compliance with the installation instructions. ~ Installation and repair work should be performed by a Miele authorized service technician.
IMPORTANT SAFETY INSTRUCTIONS ~ Do not handle frozen food or ice with wet hands. Danger of injury. ~ Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. Disposal of your old appliance ~ Before disposing of an old appliance, first make the door latch or lock unusable. ~ Do not deactivate the water filter display. ~ Take off the doors.
Guide to the Fridge-Freezer combination a Hinged door shelf b Shelves (height adjustable) c Door shelves (height adjustable) d Floating drawer e Control panel f Humidity filter g Main switch to turn the appliance On/Off h SmartFresh drawer i Water filter j Small freezer basket k Large freezer basket l Ice cube container 7
Guide to the Fridge-Freezer combination Control panel a Access button "p" activates the control panel g Food type(s) to be stored in the SmartFresh drawer b Refrigerator h On/Off sensor button for the SuperCool function c Left SmartFresh drawer d Right SmartFresh drawer e Freezer fTemperature display X colder; Y warmer Allows you to set the desired temperature in the refrigerator or freezer section i On/Off sensor button for the ice cube maker j Sensor button for the temperature and door alarm* k Wate
Before use Before using for the first time Turning the appliance On/Off ^ Clean the inside of the appliance and the accessories with a mild solution of warm water and liquid dish soap. Dry with a soft cloth. ^ Open the upper appliance door. After installing the appliance, wait at least 30 minutes before turning the appliance on. During transport, fluids in the refrigeration system may have shifted and will need some time to settle. ^ Turn the appliance On/Off with the main switch.
Settings Using the settings When a sensor button has been selected with a finger touch, it will appear yellow. A de-selected button will appear white. Depending on the zone selected, you can now: – adjust the temperature, – select the SuperCool function, or – select settings for the SmartFresh drawers by food type. ^ Touch the access button "p" so it turns yellow. On the control panel you will now see the sensor buttons of the four appliance zones.
Settings Custom settings In the custom settings mode you can select and change functions. The function possibilities are described in the respective chapters of this manual. Function Display text Temperature °C - °F † RemoteVision Module settings ; Button sound on/off = Turning the button sound On/Off If you prefer the buttons to be silent when touched, the button sound can be turned off. ^ Touch the access button "p" so it turns yellow.
Settings ^ By touching the X button, you can choose between: = 0 : Button sound is off = 1 : Button sound is on = – : Return to menu. ^ Touch the access button "p" to confirm the setting. Turning off for longer periods of time If the appliance is not going to be used for an extended time (for example, during a vacation) some precautions should be taken. ^ Tap the X button until you see ; in the display.
Alarm The appliance is equipped with an alarm system, to ensure that the temperature does not rise unnoticed because of energy loss or open doors. The alarm system is always operational, it does not need to be turned on. Turning the temperature alarm Off As soon as the alarm condition is corrected, the alarm signal turns off and the affected zone stops flashing in the display. The "alarm" indicator goes out.
Setting the temperature Setting the temperature in the refrigerator and freezer sections Temperature range The refrigerator and freezer sections can be set independently of each other. – Refrigerator: 36°F to 46°F (2°C to 8°C) ^ Touch the access button "p" so it turns yellow. A temperature of 37°F (4°C) in the refrigerator section is recommended. The temperature can be selected within the following ranges: – Freezer: 7°F to -11°F (-14°C to -24°C).
Setting the temperature Temperature unit (Fahrenheit/Celsius) The temperature can be displayed in degrees Fahrenheit (°F) or Celsius (°C). ^ By touching the X button you can select either Fahrenheit or Celsius for the temperature display. † 0: Fahrenheit † 1: Celsius † –: return to menu ^ Touch the access button "p" to confirm the setting. ^ Touch the access button "p" so it turns yellow. ^ Tap the X button until a ; appears in the display. ^ Touch the access button "p".
SmartFresh drawers The SmartFresh drawers provide the right combination of temperature and humidity. The result is freshness up to three times longer than in the other zones of the refrigerator. Storage temperatures For fresh foods that are not adversely affected by cold, the best range is 32° - 37°F (0° - 3°C). This helps to keep the food fresh considerably longer than in the rest of the refrigerator, spoiling is minimal. The temperature is set to approx. 35°F (1.5°C).
SmartFresh drawers For optimal storage conditions, it is always best to store similar foods together in one crisper. Foods that are best stored under dry conditions – fresh fish and shellfish, meats, poultry, sausage, dairy products and deli salads. Foods that are best stored under moist conditions – fresh produce, e.g., vegetables, lettuce, herbs, mushrooms, cabbage, fruit. Remember that higher moisture levels can only be attained when the food is stored unpacked so air can circulate freely.
Using the refrigerator efficiently Different storage zones Coldest area Due to the natural circulation of air in the appliance, there are different temperature zones in the refrigerator. Cold, heavy air sinks to the lowest section of the appliance. Make use of these different zones when placing food in the appliance. The coldest area in the refrigerator is directly above the SmartFresh drawers. The temperature in the drawers themselves is even colder.
Using the freezer efficiently Freezing food Placing food in the freezer Fresh food should be frozen as quickly as possible. This helps maintain the nutritional value, vitamin content, appearance and taste of the food. Food to be frozen can be placed anywhere in the freezer section. Never refreeze partially or fully defrosted food. Consume defrosted food as soon as possible, it will lose its nutritional value and spoil if left for too long. Do not refreeze defrosted food unless it has been cooked.
Using the freezer efficiently Defrosting Cooling drinks quickly Frozen food can be defrosted in different ways: To cool drinks quickly, switch on the SuperCool function. See "SuperCool" for more information. – in a microwave oven, – at room temperature, – in the refrigerator (the cold given off by the frozen food helps to keep the other food cold), – in a steam oven. Poultry It is especially important to observe proper hygiene when defrosting poultry. Never save the liquid from defrosted poultry.
SuperCool When the SuperCool function is activated, the appliance is cooled as quickly as possible (to a factory-preset temperature). The temperature in the appliance now begins to fall, with maximum cooling in the zone selected. Switching off SuperCool SuperCool When used with the refrigerator the SuperCool function is ideal for the rapid cooling of drinks and refrigerating large quantities of food. When used with the freezer the SuperCool function is ideal for freezing large quantities of unfrozen food.
Ice cube maker For the automatic ice cube maker to operate, it must be connected to the household water supply. See "Plumbing". Turning on the ice cube maker Make sure that the ice cube container is under the ice cube maker, as far as possible. Ice cubes will not be produced unless the container is completely closed. ^ Touch the sensor button for the ice cube maker so that it turns yellow. As soon as the freezer has cooled to a freezing temperature, the ice cube tray fills with water.
Automatic defrost Refrigerator section and SmartFresh drawers The refrigerator and SmartFresh drawers defrost automatically. During normal operation, condensate and frost can form on the rear wall of the refrigerator and drawers. You do not need to remove this build-up, it will defrost and evaporate automatically with the heat generated by the appliance. Freezer section The freezer section defrosts automatically. The moisture generated in the appliance collects in the evaporator.
Adjusting the interior fittings Moving the shelves SmartFresh drawer The shelves can be adjusted according to the height of the food. These drawers are set on telescopic tracks. They can be pulled in and out for loading and unloading, or removed for cleaning. ^ Using both hands, grasp the shelf from underneath and lift slightly so that the rear of the shelf is slightly above the mountings. ^ Pull the shelf forward. ^ Move the shelf to the desired height, then insert the (rear) hooks into place.
Adjusting the interior fittings The divider in the drawer can also be removed for cleaning. ^ Remove the drawer. ^ Lift the divider upward and out. To re-insert the divider, slide it back down along the tracks. Important: If the divider is not in place, the SmartFresh drawer will not work properly. Replacing the SmartFresh drawer ^ Completely extend the telescopic tracks. ^ Lay the drawer on the tracks so that it connects in the front and back. ^ Turn the safety lock back to the vertical position.
Adjusting the interior fittings Adjusting the door shelves Removing the hinged door shelf For easier loading, unloading, and cleaning, the door shelves can be shifted or completely removed. ^ Pull the stops upward and out of the shelf, and remove the shelf lid upward. ^ Now remove the hinged container upward and out. Removing the storage shelf from above the drawer ^ Remove the rear finishing strip, move the glass plate slightly toward the rear, and carefully lift it upward and out.
Adjusting the interior fittings Ice cube container Small freezer basket The ice cube container is set on telescopic tracks, and can be removed for loading, unloading and cleaning. The small freezer basket can be removed for cleaning. ^ Slide the container forward until resistance is felt. ^ Slide the basket forward until resistance is felt. On the hinged-side of the door is a safety lock, which must be turned to a horizontal position before the drawer can be removed.
Adjusting the interior fittings Large freezer basket with partition The large freezer basket can be removed for cleaning. ^ Lift the freezer basket out of the freezer. The partition in the basket can also be removed for cleaning: Replacing the partition ^ Arrange the fasteners in an upright position and audibly click the partition into them. ^ Place the safety locks into the fasteners. Using a suitable object, e.g., coin, turn the pegs into a vertical position.
Cleaning and care Before cleaning To reduce the risk of electrical shock, disconnect the appliance from the power supply by shutting off the power main, tripping the circuit breaker or unplugging the power cord before maintenance. Never use cleaning agents containing abrasive substances such as sand, soda, acids, chlorides or chemical solvents. Non-abrasive cleaning agents are also unsuitable, as they can cause matte areas to appear.
Cleaning and care Aluminum frames The shelf frames are made of aluminum. ^ Clean the frames with a mild solution of warm water and liquid dish soap. Aluminum is susceptible to scratches and nicks, treat with care. The aluminum frames may become discolored or otherwise altered if soiling is not cleaned away promptly. ^ Unhook the filter cover, 1. in each side of the drawer and remove them along with the filters downwards starting from 2.
Cleaning and care Ventilation slits After cleaning ^ Check the ventilation slits in the base panel regularly. Remove any dirt/dust with a vacuum cleaner or brush. Clean as needed. ^ Return all shelves and accessories. Door seals Do not use oil or grease on the door seals. This may cause the seals to deteriorate and become porous over time. ^ Clean the door seals with warm water and dry thoroughly.
Cleaning and care Changing the light bulb The lighting automatically switches off after the door has been open for approx. 5 minutes. This is not a fault. Never touch a halogen bulb with bare fingers. When inserting a glass halogen bulb always hold it with a soft cloth. After the bulb has cooled for a short time it will turn on again. If the light does not come on when the door is opened briefly, the light bulb should be changed. ^ Use the main switch to turn the appliance off.
Cleaning and care Side lighting ^ Turn the light cover counterclockwise and pull out. Never touch a halogen bulb with bare fingers. When inserting a glass halogen bulb always hold it with a soft cloth. ^ Pull the defective light bulb from the socket. ^ Place the new bulb in the socket. Halogen bulb type: 5 W/12 V/socket G 4. ^ Put the light cover back on and turn clockwise into place. ^ Restore power to the appliance.
Water filter The water filter improves the taste and smell of ice cubes by removing chlorine and other substances from the incoming tap water. – Depending on how many ice cubes are produced, the filter will need to be changed approximately every 6 months. It is important to change the water filter regularly.
Water filter Exchanging the water filter ^ Push in and rotate the filter cap on the base panel of your appliance counterclockwise 180°, 1. ^ Pull the used filter cartridge out of the appliance, 2. ^ Remove the cap from the used filter, 3. ^ Take a new filter cartridge out of the packaging and remove the protective cap. ^ Push the cap onto the new filter cartridge, 4. ^ Push the filter cartridge with cap, in a horizontal position, all the way into the opening in the base panel, 5.
Water filter Re-setting the filter indicator The filter indicator still flashes in the display. ^ Touch the access button "p" so it turns yellow. The various appliance zones are now visible. ^ Touch the sensor button for the refrigerator so it turns yellow. ^ Note the position of the X button, but do not touch. ^ Touch the access button "p" again so it turns white. Only the access button "p" is visible. ^ Place one finger on the position of the X button and hold (the X button will not be visible).
Water filter ^ Tap the X button until ^ - appears in the display. ^ Touch the access button "p". ^ Tap the X button until ; appears in the display. ^ Touch the access button "p". You have left the Custom settings mode. The "filter" indicator is no longer visible on the control panel. Deactivating the water filter The ice cube maker in this appliance can be operated without the installed water filter, for example if the household water supply already uses a water filter.
Filter Performance Data Sheet State of California Department of Public Health Water Treatment Device Certificate Number 06 - 1775 Date Issued: March 10, 2006 Date Revised: April 3, 2008 Trademark/Model Designation 9000 077095 Miele 07134220 Replacement Elements 9000 077104 07134220 Manufacturer: Cuno, Incorporated The water treatment device(s) listed on this certificate have met the testing requirements pursuant to Section 116830 of the Health and Safety Code for the following health related contaminant
Filter Performance Data Sheet Performance Data Sheet For Filter Model 07134220 Using Replacement Cartridge 07134220 This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI 42 and 53.
Frequently asked questions With the aid of the following guide minor problems can be corrected without a service call. Repairs should only be carried out by a qualified and trained person in strict accordance with local and national safety regulations. Unauthorized repairs could cause personal injury or machine damage and may void the warranty. Problems with temperature Issue Possible fault The refrigerator The machine is not turned or freezer on. section does not get cold.
Frequently asked questions General problems Issue Possible fault Solution Water is flowing out of Close the shut-off valve immediately. the appliance. Check whether the water Contact Miele Technical pipe in the appliance is Service. defective. Check whether the water pressure is too low. Contact a plumber. Check whether the correct Self-tapping valves and 3 water valve has been /16" (4.76 mm) saddle installed. valves reduce the water pressure and can block the pipe. The door to the This is not a fault.
Frequently asked questions Alarm / Indicator warnings Issue Possible fault Solution The alarm is ringing. The appliance door(s) have been open for longer than 5 minutes. Close the door(s). The alarm is ringing and The door is not closed. the "alarm" indicator is A large amount of food is flashing. being frozen at the same time. There has been a power failure. Once the alarm condition has been corrected, the alarm will turn off and the "alarm" indicator will stop flashing.
Frequently asked questions Problems with the ice maker Issue Possible fault Solution The ice cube maker will not switch on. The appliance is not plugged in. Check that the appliance is connected to the power supply. The ice cube maker is not producing any ice cubes. When the appliance is turned on for the very first time, it can take up to 10 hours for the first ice cubes to drop out of the ice cube maker and collect in the container. The appliance is not turned on.
Frequently asked questions Problems with the ice maker Issue Possible fault Solution The ice cubes are small. Other domestic appliances that use water are in operation. Avoid using such items as a dishwasher, washing machine or shower at the same time. Check whether the water filter needs changing. See "Water filter" for more information. Check the water pressure. The water pressure must be between 25 and 120 psi (1.72-8.25 bar). Consult a plumber.
Frequently asked questions Problems with the ice maker Issue Possible fault Solution The ice maker is not producing enough ice or the ice cubes are misshapen. Check the water pressure. The water pressure must be between 25 and 120 psi (1.72-8.25 bar). Contact a plumber. Check that the freezer temperature is not too low. See "Selecting the correct temperature". Change the water filter. See "Water filter". Check the water pressure. The water pressure must be between 25 and 120 psi (1.72-8.25 bar).
Frequently asked questions The appliance is making noises. Issue Possible fault Solution Brrrrr... Humming noise made by the compressor. This noise can get louder for brief periods when the motor is switching on. Blubb, blubb.... A gurgling noise can be heard when coolant is circulating through the pipes. These noises are not a fault. The noise of the compressor and the coolant circulating in the system is unavoidable. Click....
After sales service In the event of a fault which you cannot easily fix yourself, please contact the Miele Technical Service Department at the address on the back of this booklet. When contacting the Technical Service Department, please quote the model and serial number of your appliance given on the data plate inside the appliance.
Installation instructions To prevent accidents and machine damage read these instructions before installation or use.
Caring for the environment Disposal of packing materials Disposal of an old appliance The cardboard box and packing materials are biodegradable and recyclable. Please recycle. Old appliances contain materials that can be recycled. Please contact your local recycling center about the possibility of recycling these materials. Ensure that any plastic wrappings, bags, etc., are disposed of safely and kept out of the reach of babies and young children.
Installation Installation site Have the appliance installed by a qualified technician, according to the enclosed installation instructions. The manufacturer is not liable for damage to property due to an incorrect installation or water connection. ,WARNING This appliance is top-heavy and must be secured to prevent it from tipping forward. Keep the doors closed until the appliance is completely installed and secured as per the installation instructions. Empty weight of your machine: KF 18X1 Vi . . . . . . .
Installation Base Ventilation A fully loaded appliance is very heavy. The load-bearing capacity of your floor must meet the following requirements: The air intake and outlet must not be blocked or covered in any way. They also need to be dusted/cleaned on a regular basis. KF 18X1 Vi . . . . . . . . . 992 lbs (450 kg) KF 19X1 Vi . . . . . . . 1,190 lbs (541 kg) To ensure that the appliance is installed securely and functions properly, the base must be flat, level and made of a hard, rigid material.
Installation Custom door panels Side-by-side This appliance is compatible with all styles and designs of kitchen cabinetry. This appliance can be installed "side-by-side" with another fridge/freezer using a "Merging Kit". The total weight of the decorative panel(s) must not exceed the following: KF 18X1 Vi Upper door . . . . . . . . . . . 86 lbs (39 kg) Lower door . . . . . . . . . . . 31 lbs (14 kg) KF 19X1 Vi Upper door . . . . . . . . . . . 71 lbs (32 kg) Lower door . . . . . . . . . . .
Installation . . . with partition The minimum thickness of the partition is 5/8" (16 mm). If there is a partition between the adjacent appliances, then each appliance is to be individually installed within its own niche. The "Merging Kit" can be obtained from Miele. Side panels If one side of the appliance is visible, a side panel must be used. The side panel must be firmly secured to the wall, the floor and the overhead furniture/fixtures before the appliance is placed in the cavity.
Installation Front panel gap kit (optional accessory) Two adjacent furniture doors can be attached instead of one large door. To connect these furniture doors, a metal strip can be purchased as an optional accessory. Contact Miele. When attaching the metal strip to the furniture doors, observe the maximum length of the screws and the position of the drill holes. Always screw into the best possible load-bearing material of the custom doors.
Dimensions Niche dimensions Niche width (A) KF 1801 Vi, KF 1811 Vi 30" (762 mm) KF 1901 Vi, KF 1911 Vi 36" (915 mm) 56
Dimensions 1. Power supply 2. Water connection A KF 1801 Vi, KF 1811 Vi 15" (381 mm) KF 1901 Vi, KF 1911 Vi 18" (458 mm) Door dimensions (open min.
Installing the appliance Before you begin Read these instructions completely and carefully. Have the appliance installed by a qualified technician, according to the enclosed installation instructions. To reduce the risk of injury or damage to the product, two people should be used for installation. These installation instructions are intended for use by qualified installers. In addition to these instructions, the appliance must be installed in accordance with all local codes.
Installing the appliance Check the installation niche To ensure a safe, trouble-free installation and the best possible cosmetic result, check to be sure that the installation space complies with the installation requirements. Before installation ,Caution - the appliance is very heavy. Use caution when unpacking and opening the door, danger of tipping. ^ Check that the cavity is square. ^ To protect the base from damage during installation, attach a hard board, linoleum, etc.
Installing the appliance ^ Loosen the bracket that holds the appliance to the pallet. ,Caution! The appliance is no longer secured and may be unstable. ^ Remove the cover b. ^ Push the module into the slot until it locks into place. ^ From the rear of the appliance carefully lift it from the pallet. Once the appliance is on the ground it can be wheeled around.
Installing the appliance If the indicator light does not come on, installation of the module was unsuccessful. In that case, repeat the process. If that does not correct the problem, contact Miele. ^ Pull the antenna d straight out. ^ Guide the cover b over the antenna d and screw on the cover. ^ Angle the antenna d so that it faces to the right or left. ^ If necessary, disconnect the power supply and continue installing the appliance.
Installing the appliance Anti-tip brackets The anti-tip brackets help keep the appliance safely secured to the installation niche to prevent tipping. Two anti-tip brackets are recommended for each appliance or appliance combination (side-by-side). ^ Drill pilot holes: 1 – /8" (3 mm) for 5 x 60 mm wood screws – 1 /16" (2 mm) for 4 x 15 mm wood screws. The distance "D" between the anti-tip brackets b is the width of the appliance. ^ Tightly secure the anti-tip brackets in the niche.
Installing the appliance Securing an alternative anti-tip device – The beam must cover the appliance by at least 2" (50.8 mm). If the anti-tip brackets cannot be attached securely, an alternative anti-tip device can be used. Ensure that there is no "give" between the appliance and the anti-tip device. ^ Mark the installation height (lower edge of the beam) on the rear wall of the niche. If possible, always screw the wooden beam to existing studs.
Installing the appliance Sliding the appliance into the installation niche In the case of side-by-side installations, a separate outlet must be used for each appliance. ^ To prevent the power cord from becoming caught: Tie a piece of string to the middle of the power cord and feed it forward under the appliance. When sliding the appliance in, pull the cable forward c. ^ Carefully slide the appliance into the space until the height-adjustable wheels interlock with the anti-tip brackets d.
Installing the appliance Aligning the appliance ^ Align the appliance with the custom front. A mark is located on the appliance base and is used as a standard gauge for height adjustment. When adjusting the height, align this mark at 1 1/4" (32 mm) above the floor. ^ Place a marking-out level over the installation aids e on the door. ^ Unscrew the height-adjustable feet until the mark on the base has reached the indicated guide dimension 1 1/4" (32 mm).
Installing the appliance Note: – Do not twist or jam the appliance inside the niche. When unscrewing the height-adjustable feet, proceed gradually, alternating between left and right. – The adjustment of the rear feet is aided if the appliance is lifted at the rear (tipped forward slightly). – If using a wooden beam as an alternative anti-tip device, rotate the appliance all the way toward the wooden beam. ^ Pull out the plate side lugs i.
Installing the appliance For a side-by-side combination the filler strips from both appliances are put together to form one long filler strip: ^ Take the peg from the "side-by-side merging kit" and insert it halfway into the filler strip rail on the left-side appliance. ^ Place the second filler strip on the peg and press both filler strips together. ^ Insert both filler strips into the installation space above the appliance, until they click into place.
Installing the appliance Preparing the custom door For best results, it is important to mount the upper door before the lower door. ^ Open the appliance door. ^ Unscrew the installation supports n from the appliance door. ^ Loosen the remaining screws from the strips o on each side of the door, then remove. ^ Set aside the screws and side strips o - you will need them again later. ^ Remove the light switch cover (see arrow).
Installing the appliance ^ Mark the distance X on the back-side of the custom door. ^ Also calculate and mark the center of the custom door Y. Please note: When attaching the mounting frame onto two adjacent doors (see "Front panel gap kit") screw into the thicker outer frames of the doors only. ^ Remove the mounting frame from the appliance door and position it according to the markings on the custom door. The bracket includes a variety of holes for the various design options of custom doors.
Installing the appliance Attaching and aligning the custom door front ^ Fit the door handle to the custom door. Note that the screws are applied from the reverse side. ^ Align the custom door with the double-threaded bolts. ^ Tighten the nuts on the adjusting rail. This will correct the side alignment of the door. ^ Put the side strips o back into place and screw them completely down on both sides of the appliance door.
Installing the appliance Attaching the lower bracket (Only for appliances using the "Front panel gap kit".) ^ Measure the distance Y between the adjusting rail from the lower door and the upper door. ^ Be sure to leave a distance of 1/8" (3 mm) from the upper cabinetry door. ^ Open the lower appliance door. ^ Screw on the lower brackets. Pre-drill the holes in the custom door.
Installing the appliance The lower bracket corrects the side position of the door. Attaching the covers ^ Loosen the screw. ^ Check the side position of the door. ^ Thread the wood screw. ^ Tighten the screw. ^ Place the cover on the brackets. ^ To mount the cover strips on both sides of the upper and lower doors, click them into place from bottom to top, into the gap between the appliance door and the custom door. The number of lower brackets will depend on the width and design of the custom door.
Installing the appliance ^ Insert the cover plate on the freezer compartment door. ^ Insert the cover strip into the space between the appliance and the side panel. For side-by-side combinations, the cover strips (on both sides of the appliance) are applied to the outermost spaces only. Attaching the toe-kick panel The maximum height of the toe-kick panel is 4" (101 mm) from the top of the floor. Do not cover the ventilation slits in the base panel. Risk of damage to the appliance.
Installing the appliance ^ Put the included covering plate in place. ^ Attach the toe-kick panel to the plinth. Mounting the air separator The air separator keeps the supply and exhaust air separate. This prevents warm exhaust air from flowing into the machine, optimizing the energy performance of the unit. ^ If necessary, shorten the three parts of the air separator. ^ Insert the foam pieces back into the sides. 74 ^ Clip the air separator, left and right of the partition, in the exhaust grille.
Plumbing All plumbing work should be carried out by a suitably qualified and competent person, in accordance with all applicable local and national regulations. The manufacturer is not liable for damage to property due to an incorrect installation or water connection. The water quality must conform to country requirements for drinking water. – The appliance is only suitable for connection to the cold water supply. – The water pressure must be between 25 and 120 psi (1.72-8.25 bar).
Plumbing Preparing the water connection The connection to the household water supply must be installed before the appliance is installed. ^ Turn off the main water valve to prevent damage caused by leaking water. ^ Attach the connecting pipe to the shut-off valve, according to the instructions supplied by the manufacturer of the ice cube maker installation kit. ^ Install the connecting pipe.
Plumbing Connecting the water supply ^ Push the union nut and seal onto the water pipe. When connecting the water pipe to the solenoid valve of the appliance, follow the instructions supplied by the manufacturer of the ice cube maker installation kit. ^ Push the end of the water pipe into the appliance connection and screw on the union nut, 3. First tighten by hand. When bending the water pipe, be sure not to kink it, otherwise there is a risk of leaks and water damage. Use bending aids.
Electrical connection , Avoid the risk of electrical shock - Plug into a grounded 3-prong outlet. - Do not move the ground plug. - Do not use an adapter. - Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. Improper connection of the equipment grounding conductor may result in electric shock.
RemoteVision The Miele RemoteVision system is designed to send messages directly to Miele and/or your PC. For information on set-up and installation of the RemoteVision module see the "Installation" section of this manual. Be sure your wireless system meets the following requirements – Windows XP® or newer operating system, Mac® OS X 10.3 or higher – Cable or DSL modem – Microsoft® Internet Explorer 6 or higher, Safari 2.0 or higher, Firefox 1.
RemoteVision Accessing the RemoteVision control panel ^ Tap the X button until ; appears in the display. ^ Touch the access button "p" so it turns yellow. ^ Touch the access button "p" to confirm. See the table on the following page for a description of each setting in the display. ^ Touch the sensor button for the refrigerator section so it turns yellow. ^ Note the position of the button X, but do not touch. ^ Touch the access button "p" again so it turns white. Only the access button "p" is visible.
RemoteVision MasterCool control panel options for RemoteVision Selectable options Description of function ;- Back ;2 Reboot the module ;3 Reset the module to factory settings ;4 Enter Ad-Hoc Mode Note: If you cannot select any option (other than ; - "back"), the module has not been installed correctly.
Alteration rights reserved / 3408 For the most updated manual see the Miele web site. M.-Nr.