Operating and Installation Instructions Condenser Dryer PT 7135 C To prevent accidents and machine damage read these instructions before installation or use. en - US M.-Nr.
Contents IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Guide to the dryer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Display function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Before using for the first time. . . . . . . .
IMPORTANT SAFETY INSTRUCTIONS ,WARNING - To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions, including the following: ~ Make sure that no unattended children can access the machine. There is a potential danger that children can be trapped in the drum. This may cause major injuries or the death of the child. ~ Do not reach into the dryer if the drum is moving.
IMPORTANT SAFETY INSTRUCTIONS ~ To prevent the risk of fire, the following articles must not be dried in this tumble dryer: ~ To prevent the risk of fire, the – items which have not been washed. – fabrics which contain a large amount of rubber, foam rubber or rubber-like materials. For example, products made from latex, shower caps, waterproof textiles, rubberized articles, and items of clothing and pillows with foam rubber filling, or similarly textured rubber-like materials.
IMPORTANT SAFETY INSTRUCTIONS ~ GROUNDING INSTRUCTIONS This appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
Guide to the dryer Control panel a Display* See the following pages for more information d Optical interface PC Allows a service technician to check and update the drying programs b Direct select buttons To select a drying program directly. You can also save "Favorite" drying programs on these buttons. e Jog shuttle Turn to select Press to confirm the selection c "Start" button f a button To open the drum door. *Contents in the display will vary with program offering.
Guide to the dryer Display function Contents in the display will vary with program offering. Main menu 1 Cottons Program selection ... 2 Minimum iron Settings F ... 3 Woollens handcare 4 Smoothing 10:00 The display shows the main menu (with factory default settings). "Program selection" is highlighted. If the display is dark (in Stand-by mode) turn the jog shuttle. Jog shuttle Turn the jog shuttle to select a program or setting. Press the jog shuttle to confirm the selection.
Guide to the dryer Menu Program selection Program selection Back A Cottons Minimum iron Woollens handcare H ^ All pre-set programs can be selected with the jog shuttle. Depending on the direction the jog shuttle is turned the highlighter moves up or down. The arrows e- at the right side of the display show that more selections are available. ^ Press the jog shuttle to open the basic menu of the selected program. Basic menu of a drying program Cottons Normal Duration 1:16 h Low temp.
Before using for the first time ,The appliance must be correctly installed and connected before the first use. Please see the "Installation instructions." Welcome screen The Welcome screen shows when the dryer is turned on for the first time. Once the total use time of the dryer exceeds one hour the welcome screen will not show again. The display then shows the language selection. Language J Select the desired language and confirm with "OK".
Use Fabric care labels Before drying, check fabric care labels for special drying instructions. q = Drying with normal temperature r = Drying with low temperature s = Do not dry in a tumble dryer Drying tips – Observe the maximum loads, see the "Program guide". Overloading the dryer will result in poor drying and wrinkling. – Do not place dripping wet items in the dryer. Spin the laundry after the wash for at least 30 seconds.
Use 1. Sort the laundry 2. Load the laundry ^ Loosen up the washed laundry. ^ Use the a button to open the drum door. ^ For even drying results sort by desired dryness, fiber/fabric, size and residual moisture after spinning. ,Do not dry items that may melt or ignite in the dryer such as plastics, rubber or sneakers. They could melt and damage the laundry. ^ Load the laundry loosely into the drum. Do not overload the drum. Overloading strains the fabrics and results in poor drying.
Use 3. Select a program 6. Starting a program Two program selection possibilities: "Start" flashes when the program can be started. ^ Select a "Favorite" by pressing the respective direct select button. ^ Press the "Start" button. or The "Start" button lights. ^ Select from the "Program selection" menu by turning the jog shuttle. – The display shows "Program start" and then "Drying" with the program duration. 4. Select "Low temp." and/or "Timer" – The drying levels are displayed, e.g.
Use Remaining time 7. At the end of a program When a program is selected, the approximate duration is displayed. This is the "remaining time". "Anti-crease" (if selected) and "End" mark the end of a program in the display. During the anti-crease phase the drum will turn in intervals if the laundry is not immediately removed from the dryer to prevent the laundry from wrinkling. Run time 1 h.
Use Coin mechanism For coin mechanism operated machines: Money or tokens will be lost when the door is opened after program start or when canceling a program. Technical Service can set a time frame when a program can be changed. Adding/removing laundry during a drying program ^ Press the a button. ^ Open the door. ,Do not touch the rear of the drum while adding or removing items. Danger of burns due to high temperatures in the drum. Canceling a program ^ Add or remove items.
Program guide Programs may vary depending on the offerings of your machine. Cottons Extra dry, Normal+, Normal Items Load size: 15 lbs (6.5 kg) Single and multilayered cotton and linen laundry e.g. terry towels, beach towels, bath robes, T-Shirts, underwear, cottons bed linens, baby clothing, etc. – Select "Low temp." for items with the fabric care symbol r. – Select "Extra dry" for multilayered and thick items. – The "Extra dry" program should not be selected for jersey materials. Items may shrink.
Program guide Woollen handcare Items Note Load size: 5.5 lbs (2.5 kg) Woolen fabrics – Woolen items will be loosened up and fluffed in a short time, but not completely dried. – Remove the items immediately after the program ends and allow them to air dry. Smoothing Load size: 6.6 lbs (3.0 kg) Items – Cotton or linen fabrics – Permanent Press items of cotton, mixed fabrics or synthetics. e.g. khakis, shirts, etc. Note – Program to reduce creasing after spinning in the washer.
Program guide Load size: 7.7 lbs (3.5 kg) Jeans Normal, Hand iron r Items Denim fabric items, pants, jackets, skirts or shirts, etc. Shirts Normal, Hand iron r Items Shirts and dress shirts. Outerwear Normal, Hand iron r Items Load size: 5.5 lbs (2.5 kg) Load size: 7.7 lbs (3.5 kg) Outdoor clothing suitable to dry in a tumble dyer. Proofing Load size: 5.5 lbs (2.5 kg) Items For dryer suitable items, e.g. ski and outdoor clothing, tablecloths and poplin items.
Timer The timer allows the user to select the time of day for the program end. The program start can be delayed from 30 minutes to 24 hours. Select the submenu Timer Cottons Normal+ Low temp. Duration 1:47 h Low temp. B Timer Y Save Back A H H H H ^ Press the direct select button E. The "Timer" menu shows. Select the time Cottons Normal Low temp. 10:00 Start 10:13 Finish 12:00 ^ Select the desired program end time with the jog shuttle and confirm.
Favorites The dryer has the option to save the most used drying programs on the direct select buttons. The option "Save" must be selected in "Settings - Supervisor level". Contact Technical Service for access to this level. Selecting/Changing a Favorite ^ Close the door. Main menu 1 Cottons Program selection ... 2 Minimum iron Settings F ... 3 Woollens handcare 4 Smoothing 10:00 ^ Press the D button. Basic menu Cottons Normal Duration 1:16 h Low temp.
Favorites Depending on the selection the display shows one of the following submenus – Select a program Program selection Back A Cottons Minimum iron Woollens handcare H ^ Select the desired program with the jog shuttle and confirm. Important: If no selection is made in the submenu, the display will switch back to the basic menu after 20 seconds. – Drying level programs Cottons Normal+ Drying levels from Machine iron - Extra dry c ^ Select and confirm the desired drying level with the jog shuttle.
Favorites Low temp. To dry delicate items (fabric care symbol r) e.g. made from acrylic, press the "Low temp." button. – The temperature is reduced and the program duration is extended. ^ Press the D "Low temp." button. Saving a Favorite The basic menu shows all selected components. Cottons Normal+ Low temp. Duration 1:47 h Low temp. B H Timer Y H Save H Back A H ^ Press the F "Save" button. Assigning a direct select button Cottons Normal+ Low temp.
Cleaning and Care Cleaning the lint filters Fluff from items being dried is collected by the fluff filters in the door and the door opening. Clean the filters after each drying program*. Cleaning them while dry ^ Remove any fluff from the hollow part of the door opening. You could also use a cleaning brush which is available as an optional extra from your Miele dealer or the Miele Spare Parts Department or use a vacuum cleaner.
Cleaning and Care Cleaning them with water If there is a great deal of compacted lint on any of the filters, they can be removed and cleaned under hot running water. ^ Open the door and pull the fluff filter out of the door as described previously. The two filters in the door opening can also be removed if you need to clean them with water. Replacing the filters ,Do not replace the filters if they are damp or wet. Damp or wet filters could cause operational faults.
Cleaning and Care Cleaning the exterior and the control panel ,To reduce the risk of electric shock, disconnect the appliance from the power supply by unplugging or tripping the circuit breaker. ,Do not use an abrasive cleaner, glass cleaner or all-purpose cleaner. They will damage the dryer. ,Do not hose the dryer down. ^ The exterior and the control panel can be cleaned with warm water and liquid dish soap applied with a soft sponge. Wipe dry using a soft cloth.
Cleaning and Care Cleaning the heat exchanger ,Check the heat exchanger unit regularly. It should always be cleaned immediately the Clean heat exchanger or Clean out airways message appears. Removing the heat exchanger ^ Open the access panel. ^ Turn the lever on the inner cover downwards to the vertical position. ^ Pull the cover forwards. ^ Remove it by pulling it diagonally upwards. The hooks at the side will prevent the panel from falling off. ^ Now remove the panel by pulling it diagonally upwards.
Cleaning and Care If you cannot see any fluff: ^ Replace the heat exchanger unit (see following page). If you can see some fluff: ^ Clean the heat exchanger unit as described below. Cleaning the heat exchanger unit ^ When rinsing the heat exchanger unit, make sure you position it as shown in the next two illustrations. ^ Pull the heat exchanger unit out of its housing by the handle. Checking the heat exchanger unit ^ Use a shower head or similar to rinse the unit out as shown.
Cleaning and Care When replacing the cover after cleaning, ensure that the rubber seal fits correctly into the groove. ^ Replace the cover making sure the hooks locate correctly. Hold it at an angle and push it gently downwards. ^ Then turn the lever upwards into the horizontal position to lock the cover. ^ Replace the service panel and press the upper edge until it clicks into position. ^ Then flush the unit through from the front.
Frequently asked questions Repairs to electrical appliances must only be carried out by a qualified and trained technician in accordance with local and national safety regulations. Unauthorized repairs could cause injury or machine damage. Check and fault messages in the display What if ... l Adjust the load , Technical fault A numerical fault message shows, e.g. "F47". 28 Possible cause Solution This is not a fault. The electronic reads that no laundry is in the drum and cancels the program.
Frequently asked questions What if ... At the end of a program Maintenance message or Clean the heat exchanger appears Clean out airways Possible cause The dryer reminds you to clean the heat exchanger. You can adjust the setting which controls when or if the Maintenance message appears. Solution – Clean the heat exchanger. To delete this message: – Confirm with "OK". – See "Settings - Supervisor level - Cleaning the heat exchanger".
Frequently asked questions Other faults What if ... The program runs too long or stops. Possible fault Solution In some cases "Clean out airways" is displayed. Check all the possible causes and open and shut the dryer door. Ventilation to and from the dryer may be insufficient (e.g. because it is installed in a small room). This has caused the temperature in the room to rise sharply. The lint filter is clogged with lint or were still wet when they were replaced. The vents below the door are blocked.
Frequently asked questions What if ... Possible fault Solution The inner cover of the heat – Ensure that the heat exchanger unit has not been exchanger unit is locked properly and/or the positioned correctly and lock the cover. heat exchanger unit has not been positioned correctly. – Check the rubber seals. Water leaks form Lint has collected at the the machine after – Use a cloth to remove any the heat exchanger bottom of the condenser unit lint from the inside of the housing.
Frequently asked questions What if ... Possible cause Solution A program cannot be started, the display remains dark. The fault cannot be detected immediately. – Is the dryer connected to the power mains? – Is the door closed? – Are the fuses blown? After closing and opening the door the light comes back on. The drum light does The light turns off not come on. automatically (energy saving). The bulb may be bad or burnt out. The display shows a foreign language.
Frequently asked questions Changing the light bulb ,To reduce the risk of electric shock, disconnect the appliance from the power supply by unplugging or tripping the circuit breaker. ^ Open the door. The bulb cover is located along the ,The light bulb must not exceed the maximum wattage listed on the data plate. ^ Replace the light bulb with a new one. ^ Flip the light bulb cover upwards and press it firmly into the left and right sides until it clicks into place.
After sales service In the event of a fault which you cannot fix yourself, please contact the Miele Technical Service Department at the address on the back of this booklet. When contacting the Service Department, please quote the model and serial number of your appliance. They can be found on the data plate located below the drum opening. The PC indicator allows a service technician to check and update the drying programs.
INSTALLATION INSTRUCTIONS To prevent accidents and machine damage read these instructions before installation or use.
IMPORTANT SAFETY INSTRUCTIONS , WARNING - Risk of Fire ~ To reduce the risk of severe injury or death, follow all installation instructions. ~ Clothes dryer installation must be performed by a qualified installer. ~ Install the clothes dryer according to the manufacturer's instructions and local codes. ~ Check the packaging, the dryer and accessories for any signs of damage. Do not use a damaged appliance. ~ Repair and maintenance work should be performed by a Miele authorized service technician.
Installation Front view a Power cord b Control panel f External drainage options (e.g. via sink, drain or gully).
Installation Side view Top view Rear view Washer/ Dryer Stack a Lid over hang with transport grips (arrow) The Miele dryer can be installed as part of a washer-dryer stack in combination with a Miele washer. An appropriate "stacking kit" available from Miele is required. Installation of the stacking kit must be completed by a Miele Service Technician.
Installation Installation on a cement base Coin mechanism The dryer can be equipped with a coin mechanism (optional accessory). Miele’s Technical Service will install the coin mechanism and program the electronic. Empty the coin mechanism regularly to avoid jams. ^ Secure the front feet of the dryer with retaining clips on the cement base. ,Do not install devices to automatically turn the dryer off, e.g. clock timers.
Installation Installation ,Do not install a lockable or slide door in the pivoting area of the dryer door. Transporting the dryer to the installation site The rear overhang of the lid has transport grips. ^ Use the front dryer feet and the rear overhang to transport the dryer from the packaging base to the installation site. Level the dryer ^ The machine can be leveled by turning the legs clockwise or counterclockwise as necessary.
Installation External drainage of the condensed water The condensed water is pumped away through the drain hose which is located at the back of the dryer at the bottom. Drain hose length: . . . . . . 6' 6 3/4" (2 m) Drain pump height: . . . . . 3' 3 3/8" (1 m) ,Do not pull on the drain hose and do not allow it to become kinked as this could cause damage. Drain hose connection: ^ Remove the adapter 1 and the hose clip 3 behind it. 1. Direct into a sink or basin. – Hook the hose over the edge and secure.
Installation Electrical connection ,This installation should be performed by an experienced and qualified technician, in accordance with local codes and regulations. GROUNDING INSTRUCTIONS This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment grounding conductor and a grounding plug.
Technical Data Height 33 7/16" (850 mm) (adjustable + / - 1/4" (7 mm)) Width 23 7/16" (595 mm) Depth Depth with the door open 27 9/16" (700 mm) 46 3/4" (1,188 mm) Weight Drum 128 lbs (58 kg) 28.6 gal (130 l) Maximal load Power cord 14.3 lbs (6.5 kg) Dry laundry weight 63" (1.6 m) Fuse rating Rated load see data plate see data plate Fuse rating Light load see data plate see data plate Maximum floor pressure during operation approx.
Caring for the environment Disposal of the packing materials The cardboard box and packing materials protect the appliance during shipping. They have been designed to be biodegradable and recyclable. To prevent suffocation, ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of children. 44 Disposal of an appliance Old appliances may contain materials that can be recycled.
Menu Settings J to adjust standard settings The dryer controls can be adjusted to changing demands through the settings. Depending on default settings: – some settings are visible and can be changed by all users (Menu "Settings J") or – all setting are locked in the "Supervisor level" by a code (Menu "Settings - Supervisor level"). Contact Miele Technical Service.
Settings J Opening the menu Settings 1 Cottons Program selection ... 2 Minimum iron Settings F ... 3 Woollens handcare 4 Smoothing 10:00 ^ Select "Settings" J in the main menu and confirm by pressing the jog shuttle. Selecting Settings Settings Back A Language F ... Anti-crease Buzzer H ^ Select the setting to be changed and confirm. If no selection is made in the submenu, the display will switch back to the "Settings" menu after 20 seconds.
Settings J Language J The displayed language can be set in the submenu "Language J". The flag behind the word "Language J" is a guide to find the settings menu in case a foreign language is selected. ^ Select the desired language and confirm. The change is only valid for the current program. At the end of the program the display language will change back to the language set in the "Settings Supervisor level".
Settings J Contrast/Brightness Display contrast and brightness can be adjusted in 10 levels. Lengthening the cooling time The cooling phase can be lengthened before the program is started. The laundry will be cooled. The bar shows the selected level. The bar shows the selected level. Standby The display goes into standby mode after 10 minutes and the "Start" button flashes slowly to save energy. on Standby is turned on: – when no program is selected. – after pressing the "Start" button.
Settings - Supervisor level The menu "Settings - Supervisor level" is locked with a code to prevent unauthorized access (except Language J). It must be activated by Technical Service. Settings Back A Supervisor level Access via code ^ Select "Access via code" and confirm. Entering the code ^ Enter the code "0 0 0" (factory default). If a wrong code is entered three times, the code entry will be locked for 1 hour. 0 _ _ Please enter code ^ Turn the jog shuttle until the first digit shows.
Settings - Supervisor level Language J The display contents can be shown in different languages. The fixed default language can be set in the submenu "Language J". ^ Select the desired language and confirm with "OK". Sort languages The order of the first 4 languages in the display can be set, when the option "Language menu international" or "Language menu International 4 languages" is selected. Supervisor level The access code for the supervisor level can be changed. ^ Enter the old code.
Settings - Supervisor level Language entry A selection can be set to show an additional welcome menu with language selection before the entry menu and at the end of the program. national: no additional welcome menu international: The welcome menu shows. A language must be selected. All languages are available. See "Sort languages". Drying levels The bars show the selected level. Factory default: medium level – The program duration shortens (more moist) or lengthens (more dry).
Settings - Supervisor level Cleaning the airways The lint filters must be cleaned after every drying cycle. Additionally the indicator "Clean out airways" lights once a certain level of lint is collected. The user can decide at which level of lint collection the indicator should come on. off "Clean out airways" does not light up heavy "Clean out airways" shows only when large amount of lint is collected. normal Factory default light "Clean out airways" shows even when a small amount of lint is collected.
All rights reserved / 5014 M.-Nr. 10 037 980 / 00 INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.
