NOTEBOOK COMPUTER RK10 User’s Guide (PRELIMINARY DRAFT)
Notice The company reserves the right to revise this publication or to change its contents without any notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
Revision History: Revision Date Changes Author II
FCC (Federal Communications Commission) Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and radiates radio frequency energy. If not being installed and used in accordance with the instructions, it may cause harmful interference to radio communications.
Regulatory Information/ Disclaimers Installation and use of this computer must be in strict accordance with the instructions included in the user documentation provided with the product. Any changes or modifications (including the antennas) made to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment.
CE Products with the CE Marking comply with both the (2004/108/EC) and the Low Voltage Directive (2006/95/EC) issued by the Commission of the European Community.
CE Declaration of Conformity It is confirmed to comply with the requirements set out in the Council Directive on the approximation of the laws of the member states relating to Electromagnetic Compatibility (2004/108/EC), Low-voltage Directive (2006/95/EC), the Amendment Directive (93/68/EEC), and the procedures given in European Council Directive (99/5/EC and 2004/108/EC). The equipment was passed, and the equipment test was performed according to the following European standards: EN 300 328 V1.7.
Power Conservation This computer consumes much less power than conventional computers. However, power consumption may be reduced by configuring the Power Management Setup properly. It is recommended the power saving functions to be enabled even when not running on battery power. Power Management will not degrade performance while saving power. Power Safety There are specific power requirements for this computer: z Only use an approved power adapter for this computer.
Battery Precautions z z z z z z Only use the batteries designed for this computer. The wrong battery may cause explosion, leakage or damage to the computer. Do not remove the battery from the computer while it is powered on. Do not continuously use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer is able to continuously work with a damaged battery, the circuit damage may occur and possibly cause fire.
Environmental Information, Material Safety & Recycling All materials used in the manufacturing of this equipment are recyclable or environmentally friendly. Please recycle the packing materials by the local regulations at the end of the product's service life. Notice: z The equipment may still contain tiny amount of hazardous substances for health and environment, though those are below control level.
TABLE OF CONTENTS CHAPTER ONE - GETTING STARTED ........................................ 1 UNPACKING .................................................................................................1 QUICK OPERATION .......................................................................................2 APPEARANCE OVERVIEW ..............................................................................3 CHAPTER TWO - OPERATING INFORMATION .......................... 8 WORKPLACE ...............................
RF DEVICE CONTROL CONFIGURATION SUB-MENU.......................................33 EC THERMAL CONTROL SUB-MENU ............................................................34 CHIPSET MENU ..........................................................................................35 CHIPSET MENU SELECTIONS .......................................................................35 PCH-IO CONFIGURATION SUB-MENU ..........................................................35 BOOT MENU ..................................
CHAPTER SEVEN - OPTIONAL DEVICES ................................ 51 COMMUNICATION........................................................................................51 MEMORY CARD ..........................................................................................51 VEHICLE ADAPTER .....................................................................................51 2ND BATTERY ............................................................................................51 2ND HDD ...............
Getting Started Chapter One - Getting Started Unpacking The following components are along with your computer. If there is any missing or damaged, please notify the dealer immediately.
Getting Started Quick Operation z z z Loosen the battery screw, remove the battery insulation sheet, and mount the battery. Connect the AC adapter with the computer and start charging the battery for at least 10 minutes. Turn ON the computer by pressing the power switch. Notice: z When ambient temperature is under +5℃ (This is the default setting for this computer.), the system may not boot up immediately. System will beep with LED heater light flashing to remind the user while heater working.
Getting Started Appearance Overview LCD Panel Open 6 2 1 3 4 5 1. 2. 3. 4. 5. 6.
Getting Started Right View 1 1. 2. 2 Flex Bay: a. Standard: SATA ODD (Optical Disk Drive) b.
Getting Started Left View 1 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 2 3 4 5 6 7 8 9 PS/2 Port (Keyboard + Mouse) GLAN RJ45 IEEE1394 Port (Fire Wire) USB Port 3.0 x 2 USB Port 2.
Getting Started Rear View 1 1. 2. 3. 4. 5. 6. 7. 8. 9.
Getting Started Bottom View 1 2 3 1. 2. 3.
Operating Information Chapter Two - Operating Information Workplace A clean and moisture-free environment is preferred. Make room for air circulation. Remember to avoid areas from: z z z z Sudden or extreme changes in temperature. Extreme heat. Strong electromagnetic fields (near television set, motor rotation area, etc.). Dust or high humidity. If it is necessary to work in a hostile environment, please regularly maintain your notebook computer by cleaning dust, water, and etc.
Operating Information Operating System Your computer is designed to operate with Microsoft Windows 7/8 32/64-bit Operating System. Please connect your computer with an external USB-interface drive, such as an ODD or a USB thumb drive, and start the OS installation. Work with Power Button Since the notebook computer is equipped with a heater kit to enable the unit to work under low temperature, the heater will first heat HDD up to the temperature set by user, and the system will boot after then.
Operating Information Shut down Before shutting down, please always remember to save the unfinished works and close the application for preventing from any possible data loss or HDD damage. “Shut down” will totally turn OFF the power of your notebook computer. If you want to start your notebook computer again, you need to press the power switch. Sleep/Hibernate Sleep Under “Sleep” mode, the system will temporarily save your work into RAM.
Operating Information Intel® Rapid Start Technology Your computer can operate Intel® Rapid Start Technology when SSD is installed. This technology enables your system resume time not only to be as fast as wake-up time from S3 (Sleep) mode, but also to be more energy saving.
Operating Information Keyboard The keyboard is functionally equivalent to a full size desktop keyboard. A sample layout is shown below. You can use keyboard to adjust LCD backlight by pressing and holding [Fn] + [F3] to decrease the brightness or [Fn] + [F4] to increase the brightness. The Numeric Keypad The numeric keypad functions are the same as an electronic calculator. It is embedded in the main keyboard, with the numeric figures printed on the upper right of their respective keys.
Operating Information Hard Disk Drive (HDD) The Hard Disk Drive (HDD) is a 2.5” type/ 9.5mm height SATAII interface data storage device. HDD and ODD (Optical Disk Drive) are removable. This design provides convenience and security. They can ONLY be removed when the power is OFF. Note: NEVER drop your HDD, ODD or expose them to high temperature, high humidity, or any hazardous environment. NEVER try to disassemble the module. Static discharge may destroy your device and data.
Operating Information Read from the ODD The ODD may be designated as drive D: or higher depending on your configuration. You may access to it in DOS or Windows. Please avoid shock or vibration when the optical device is active. Express Cards The computer supports 54 mm or 34 mm wide ExpressCard. You can install an ExpressCard while the computer is running. The computer automatically detects the card. To install an ExpressCard: - Hold the card with the top side of the card.
Operating Information RTC Battery backed up RTC (Real Time Clock/Calendar) is built in an on-board CMOS (Complementary Metal Oxide Semiconductor) chip. The RTC keeps track of the time and date while the computer is off. The CMOS chip also stores system setup information. RTC battery is also recharged when AC adapter is attached. Recharge the computer approximately once per month to ensure RTC operation.
Operating Information Replacing Modules To remove the modules: 1. Turn OFF the computer or hibernate. 2. Disconnect all cables from the computer. 3. Use a coin to turn and loose the screws on the modules. 4. Remove the battery from the compartment. 5. Push the latch knob to release the ODD or HDD module and push them outward. 6. Remove the module from the computer. To re-install the modules: Gently push the module into the slot. Fasten the screw to fix the module.
Operating Information Wireless Devices (Option) Before using wireless devices, please turn “ON” the Wireless Devices All ON/OFF Switch, and then use the Device Power Manager to do the rest settings. The following instructions are only for the models with optional Wireless Devices (Wireless LAN/ Bluetooth/ GPS) and taking the systems working under Windows 7/ 64-bit OS for example. Wireless LAN 1. Driver & Application Installation: a. Install the Chipset Driver first. b. Then, install the Wireless Manager.
Operating Information Bluetooth 1. Driver & Application Installation: a. Install the Bluetooth driver first. b. Then, install the Wireless Manager. 2. Launch the Wireless Manager: a. Launch the Wireless Manager. b. Click “Bluetooth” for enabling the Bluetooth function (click again for disabling the Bluetooth function). Once the Bluetooth starts up, the RF LED will turn on accordingly.
Operating Information GPS 1. Driver & Application Installation: a. Install the GPS driver first. b. Then, install the Device Power Manager. 2. Launch the Device Power Manager: a. Launch the Device Power Manager. b. Click “GPS” for enabling the GPS function (click again for disabling the GPS function). Once the GPS starts up, the RF LED will turn on accordingly.
Operating Information DockUnder DUK1X (Option) (to be added about here) .
Managing Power Chapter Three - Managing Power AC Adapter The AC adapter performs two functions: z z It powers the computer from an external AC source. It charges the computer battery. The adapter automatically detects the AC line voltage (100V or 240V) and adjusts accordingly. The following are recommended when using the AC adapter: z z Use a properly grounded AC outlet. Use one AC outlet exclusively for the computer. Having other appliances on the same line may cause interference.
Managing Power Battery The power source will automatically switch to battery when the external power source (AC adapter or optional vehicle adapter) is disconnected. Battery Low When the battery is nearly exhausted, the computer gives the following “Battery Low” warnings: z Windows battery low warning (when operating system is Windows). z The power LED flashes. Once the Battery Low warning occurs, please: z Save and close the files you are currently working on.
Managing Power Battery Gauge You may check battery status from battery gauge in Windows. Click the power/battery icon to reveal the battery gauge window. Battery Power Saving Tips The computer comes with an intelligent power-saving feature. You may extend the battery life by: z Setup power saving functions in Operating System Power Management options (e.g. Windows Power Options). z Lower the intensity of the display by brightness control. z Use standby option when computer is temporarily not in use.
Managing Power Power Conservation This computer consumes much less power than conventional computers. However, power consumption may be reduced by configuring the Power Management Setup properly. It is recommended the power saving functions to be enabled even when not running on battery power. Power Management will not degrade performance while saving power. Supporting ACPI Your notebook computer supports ACPI (Advanced Configuration and Power Interface) for power management.
BIOS Setup Chapter Four - BIOS Setup Press [F2] at boot up to enter BIOS setup. Use arrow keys to select options and [+/-] to modify them. When finished, move to “Exit” and press [Enter] then confirm save by pressing [Y].
BIOS Setup Advanced Menu Main Advanced Aptio Setup Utility Chipset Boot Security Trusted Setting ► Trusted Computing ► SATA Configuration ► Intel (R) Rapid Start Technology ► USB Configuration ► IT8783F Super IO Configuration ► RF Device Control ► EC Thermal Control Save & Exit Computing →←: Select Screen ↑↓: Select Item Enter: Select –/+: Change Opt.
BIOS Setup Advanced Menu Selections You can make the following selections on the Advanced Menu. Feature Options Description Trusted Computing Disabled Enabled TPM Support SATA Configuration SATA Mode Selection SATA Mode Selection: IDE, AHCI, Serial ATA Port 0 RAID Software Preserve Intel (R) Rapid Disabled Start Technology Enabled USB Configuration Enable or disable Intel (R) Rapid Start Technology. Disabled Enabled Legacy USB Support USB3.
BIOS Setup Trusted Computing Sub-Menu Aptio Setup Utility Advanced Configuration TPM SUPPORT [Disable] Current Status Information SUPPORT TURNED OFF Enables or Disables BIOS support for security device. O.S. will not show Security Device. TCG EFI protocol and INT1A interface will not be available. →←: Select Screen ↑↓: Select Item Enter: Select –/+: Change Opt.
BIOS Setup SATA Configuration Sub-Menu Aptio Setup Utility Advanced Determine how SATA controller(s) operate. SATA Mode Selection [AHCI] Serial ATA Port 0 Software Preserve Serial ATA Port 1 Software Preserve Serial ATA Port 2 Software Preserve Empty Unknown Empty Unknown SATA SSD (120.0 SUPPORTED →←: Select Screen ↑↓: Select Item Enter: Select –/+: Change Opt.
BIOS Setup Intel (R) Rapid Start Technology Sub-Menu Aptio Setup Utility Advanced Intel (R) Rapid Start Technology [Disabled] Enables or disable Intel (R) Rapid Start Technology →←: Select Screen ↑↓: Select Item Enter: Select –/+: Change Opt.
BIOS Setup USB Configuration Sub-Menu Aptio Setup Utility Advanced Enables Legacy USB support. AUTO option disables legacy support if no USB devices are connected. Disable option will keep USB devices available only for EFI applications USB Configuration USB Devices: 1 point Legacy USB Support USB3.0 Support XHCI Hand-off EHCI Hand-off [Enabled] [Enabled] [Enabled] [Disabled] →←: Select Screen ↑↓: Select Item Enter: Select –/+: Change Opt.
BIOS Setup IT8783F Super IO Configuration Sub-Menu Aptio Setup Utility Advanced Set Parameters of Serial Port 0 (COMA) IT8783F Super IO configuration IT8783F Super IO Chip ►Serial Port 0 Configuration IT8783F →←: Select Screen ↑↓: Select Item Enter: Select –/+: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit IT8783F Super IO Configuration Sub-Menu Selections You can make the following selections on the IT8783F super IO configuration sub-menu.
BIOS Setup RF Device Control Configuration Sub-Menu Aptio Setup Utility Advanced RF Device Control Setting RF Device Control GPS STATUS GPS BT STATUS BLUETOOTH WLAN STATUS WLAN Present [Enabled] Present [Enabled] Present [Enabled] →←: Select Screen ↑↓: Select Item Enter: Select –/+: Change Opt.
BIOS Setup EC Thermal Control Sub-Menu Aptio Setup Utility Advanced EC Thermal Control Setting EC Thermal Control Thermal cooling trip point [87 C] →←: Select Screen ↑↓: Select Item Enter: Select –/+: Change Opt.
BIOS Setup Chipset Menu Main Aptio Setup Utility Chipset Boot Advanced Security Save & Exit System Agent Parameters ► System Agent (SA) Configuration ► PCH-IO Configuration (SA) →←: Select Screen ↑↓: Select Item Enter: Select –/+: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Chipset Menu Selections You can make the following selections on the Chipset sub-menu.
BIOS Setup PCH-IO Configuration Sub-Menu Selections You can make the following selections on the PCH-IO Configuration sub-menu. Feature Options Description PCH LAN Controller Disabled Enabled Enable or disable onboard NIC.
BIOS Setup Boot Menu Main Advanced Aptio Setup Utility Chipset Boot Security Save & Exit Sets the order Boot Option Priorities Boot Option #1 [P2: SATA SSD...] Boot Option #2 [IBA GE Slot 00C8 v...] Network Device BBS Priorities Hard Driver BBS Priorities system boot →←: Select Screen ↑↓: Select Item Enter: Select –/+: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit The system will try to boot from device on top then the 2nd and so on.
BIOS Setup Security Menu Main Aptio Setup Utility Chipset Boot Advanced Security Save & Exit Set Password Password Description If ONLY the Administrator’s password is set, then this only limits access to Setup and is only asked for when entering Setup. If ONLY the User’s password is set, then this is a power on password and must be entered to boot or enter Setup. In Setup the User will have Administrator rights.
BIOS Setup Save & Exit Menu Main Advanced Aptio Setup Utility Chipset Boot Security Save & Exit Exit system setup after saving the changes Save Changes and Exit Discard Changes and Exit Save Changes and Reset Discard Changes and Reset →←: Select Screen ↑↓: Select Item Enter: Select –/+: Change Opt.
Drivers and Applications Chapter Five - Drivers and Applications The Utility DVD includes all the drivers for the installed devices in your notebook computer. Please consult the dealer if there is any driver missing. Also, through Device Manager in Windows, you are able to perform “Driver Update” or check if there are still drivers for the devices needed to be installed. Please check the readme file on Utility DVD to get the latest information before installing device drivers.
Drivers and Applications Audio Windows 7/Ultimate 64-bit: Run "Setup.exe" in the directory of "\Drivers\Windows 7 (64-bit)\Audio\6777_PG360_Win8_Win7_Vista_XP", and then follow the instructions to install. Windows 7/Ultimate 32-bit: Run "Setup.exe" in the directory of "\Drivers\Windows 7 (32-bit)\Audio\6777_PG360_Win8_Win7_Vista_XP", and then follow the instructions to install. Intel ME Windows 7/Ultimate 64-bit: Run "Setup.exe" in the directory of "\Drivers\Windows 7 (64-bit)\Intel_ME\MEI_allOS_7.1.40.
Drivers and Applications Wireless Power Manager Windows 7/Ultimate 64-bit: Run "setup.exe" in the directory of "\Utilities\", and then follow the instructions to install. Windows 7/Ultimate 32-bit: Run "setup.exe" in the directory of "\Utilities\", and then follow the instructions to install. Touch Screen Windows 7/Ultimate 64-bit: Run "setup.exe" in the directory of "\Drivers\Windows 7 (64-bit)\Touch Screen\PenMount Windows Universal Driver V2.4.0.306(WHQL)", and then follow the instructions to install.
Drivers and Applications Ricoh Windows 7/Ultimate 64-bit: Run "setup.exe" in the directory of "\Drivers\Windows 7 (64-bit)\Ricoh\Ricoh_Media_Driver_v2.13.16.01", and then follow the instructions to install. Windows 7/Ultimate 32-bit: Run "setup.exe" in the directory of "\Drivers\Windows 7 (32-bit)\Ricoh\Ricoh_Media_Driver_v2.13.16.01", and then follow the instructions to install. Turbo Boost Monitor Windows 7/Ultimate 64-bit: Turbo Boost Monitor : Run "setup.exe" in the directory of "\Drivers\Windows 7 (6
Drivers and Applications 2nd Gigabit LAN (Option) Windows 7/Ultimate 64-bit: Run "setup.exe" in the directory of (64-bit)\RTL8111E\Install_Win7_7046_07202011", instructions to install. "\Drivers\Windows 7 and then follow the Windows 7/Ultimate 32-bit: Run "setup.exe" in the directory of (32-bit)\RTL8111E\Install_Win7_7046_07202011", instructions to install. "\Drivers\Windows 7 and then follow the WiFi (Option) Windows 7/Ultimate 64-bit: Run "iprodifx.exe" in the directory of "\Drivers\Windows (64-bit)\
Drivers and Applications GPS (Option) Windows 7/Ultimate 64-bit: *: First into the "Wireless Power Manager" to turn on the GPS device. Run "ublox_A4_U5_USB_drv3264_install_UI.exe" in the directory of "\Drivers\Windows 7 (64-bit)\UBlox 6H Driver", and then follow the instructions to install. Windows 7/Ultimate 32-bit: *: First into the "Wireless Power Manager" to turn on the GPS device. Run "ublox_A4_U5_USB_drv3264_install_UI.exe" in the directory of "\Drivers\Windows 7 (32-bit)\UBlox 6H Driver", and then f
Drivers and Applications TPM (Option) Windows 7/Ultimate 64-bit: Run "setup.exe" in the directory of "\Drivers\Windows 7 (64-bit)\TPM", and then follow the instructions to install. Windows 7/Ultimate 32-bit: Run "setup.exe" in the directory of "\Drivers\Windows 7 (32-bit)\TPM", and then follow the instructions to install.
Specifications Chapter Six - Specifications Platform z Intel® Huron River Platform CPU z Intel® Sandy Bridge i7-2610UE (4 MB Intel Smart Cache Memory) CPU runs at multiple speeds depending on the CPU type and operating system. Also, CPU speed switches automatically by detecting AC adapter/ battery operation and busy state. PCH z Intel® Cougar Point QM67 Memory z - Max.
Specifications Touchpad z z Type: Life time: PS/2 Capacitive Touchpad Optional PS/2 Resistive Touchpad Over 5,000,000 strokes lifetime Hard Disk Drive (HDD) / Optional Solid State Drive (SSD) z z z Type: Height: Interface: 2.5” (Removable) 9.5mm SATAⅡ Optical Disk Drive (ODD) z z z Type: Height: Interface: 5.25” (Removable) 12.7mm SATAⅡ I/O Ports z z z z z z z z z z z z z z z PS/2 x1 (KB + mouse) USB 3.0 x 2 USB 2.
Specifications AC Adapter z z z z z z AC Input: Frequency: DC Output: Maximum Power: Dimension: Weight: 100 - 240 V 50/60 Hz 19V 90 Watts Max. Output 130mm (W) x 60mm (D) x 34mm (H) 430 g (0.9 lb.) Battery Primary Battery: z Type: z Capacity: z Dimension: z Weight: 9 x 18650 cells Lithium Ion 10.8V 8700mAh 103 mm (W) x 73 mm (D) x 38 mm (H) 435 g 2nd Battery (Optional): z Type: 9 x 18650 cells Lithium Ion z Capacity: 10.
Specifications Materials and Recycling Materials of the computer are as follows: z Cabinet: Aluminum Alloy ADC-12 Magnesium Alloy AZ91D UL grade PC+ABS GE C6200 or TN-3813BW z Bracket: Aluminum 5052 Steel with Nickel Plating or Stainless Steel S304 z Cushion pad: Silicon Rubber TPE z PCB: FR-4 UL 94V0 z Battery: Rechargeable Lithium Ion, 9 Cells per Pack z Packing: Carton - Unbleached Paper Cushion - Recyclable EPE Carrying bag - Recyclable PE Fiber Quick Guide - Recycled/Recyclable Paper Please recycle th
Optional Devices Chapter Seven - Optional Devices Communication z WiFi/Bluetooth: - Intel® Centrino® Advanced-N 6235, Dual Band - Board Form Factor: PCIe Half Mini Card - Wi-Fi Certified: 802.11 a/b/g/n - Bluetooth: Supports BT 2.1, 2.1+EDR, 3.0, 3.0+HS, 4.0 (BLE) - Interface: PCIe (WiFi)/USB (BT) z GPS: u-blox LEA-6H (USB interface) z 2nd Gigabit LAN: 1Gbps (internal Mini PCIe Card) Memory Card The memory card will expand your memory to facilitate better system performance.
Optional Devices 2nd HDD z Trade-off with ODD; set as SATA primary slave drive. ODD z z Removable ODD for disks playing Compatible with VCD-ROM, DVD-ROM, and etc. KB Dust Cover z KB Dust Cover is available for standard Keyboard Dual Battery Charger RT202D This charger provides two bays for the Primary and Secondary Batteries respectively. It accepts power from AC adapter or vehicle adapter and charged batteries. COM 3/4 Additional Serial Ports z Supporting RS232, TTL, RS422, and RS485 formats.
Maintenance and Service Chapter Eight - Maintenance and Service Cleaning ALWAYS turn OFF the power, unplug the power cord and remove the battery before cleaning. The exterior of the system and display may be wiped with a clean, soft, and lint-free cloth. If there is difficulty removing dirt, apply non-ammonia, non-alcohol based glass cleaner to the cloth and wipe. An air gun is recommended for cleaning water and dust. For salty water please clean with fresh water then blow-dry with an air gun.
Maintenance and Service RMA Service If troubleshooting steps are unsuccessful, consult your dealer for RMA. Shipping instructions: 1. Remove any personal disks or other media. 2. Use the original shipping container and packing materials, if possible. 3. If the original packing materials are not available, wrap the equipment with soft material (e.g. PU/PE form) then put the wrapped equipment into a hard cardboard shipping box. 4.
FCC Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
