Published Manual Number/ECN: MPP72WE2AE/2006153A • Publishing System: TPAS • Access date: 4/11/2006 • Document ECN's: Latest Available Service— 72044 WP2/WP3 WasherExtractors PELLERIN MILNOR CORPORATION POST OFFICE BOX 400, KENNER, LOUISIANA 70063-0400, U.S.A.
Please Read About the Manual Identifying Information on the Cover The front cover displays pertinent identifying information for this manual. Most important, are the published manual number (part number) /ECN (date code). Generally, when a replacement manual is furnished, it will have the same published manual number, but the latest available ECN. This provides the user with the latest information applicable to his machine.
Table of Contents for MPP72WE2AE/2006153A 72044 WP2/WP3 Washer-Extractors Page Description Document/ECN 1 3 4 5 About This Manual Warranty How to Order Parts Safety—Divided Cylinder and Staph-Guard™ Washer-Extractors About the Forces Transmitted by Milnor Washer-Extractors Glossary of Tag Illustrations - Suspended WasherExtractors Avoiding Damage from Allied Remote Chemical Delivery Systems MHPHYDROAE/9541AV 10 12 18 23 24 34 35 39 40 41 42 43 44 63 64 68 69 70 71 73 74 75 76 77 78 88 89 91 BMP720
Table of Contents, cont.
Table of Contents, cont.
MHPHYDROAE/9541AV (1 of 1) ABOUT THIS MANUAL È Scope—This instruction manual is intended to provide preventive maintenance, service procedures, and Ë mechanical parts identification for your machine. See the safety manual for safety instructions before installing, servicing, or operating this machine. See the installation guide for facility requirements, installation instructions, and assembly instructions. See the operator guide for operator instructions.
2
3(//(5,1 0,/125 &25325$7,21 /,0,7(' 67$1'$5' :$55$17< We warrant to the original purchaser that MILNOR machines including electronic hardware/software (hereafter referred to as “equipment”), will be free from defects in material and workmanship for a period of one year from the date of shipment from our factory with no operating hour limitation.
How to order repair parts Repair parts may be ordered either from the authorized dealer who sold you this machine, or directly from the MILNOR factory. In most cases, your dealer will have these parts in stock. When ordering parts, please be sure to give us the following information: 1. Model and serial number of the machine for which the parts are required 2. Part number 3. Name of the part 4. Quantity needed 5. Method of shipment desired 6.
BIUUUS27 (Published) Book specs- Dates: 20051111 / 20051111 / 20060323 Lang: ENG01 Applic: HDU Safety—Divided Cylinder and Staph-Guard™ Washer-Extractors 1. General Safety Requirements—Vital Information for Management Personnel [Document BIUUUS04] Incorrect installation, neglected preventive maintenance, abuse, and/or improper repairs, or changes to the machine can cause unsafe operation and personal injuries, such as multiple fractures, amputations, or death.
Safety—Divided Cylinder and Staph-Guard™ Washer-Extractors 1.1. Laundry Facility—Provide a supporting floor that is strong and rigid enough to support–with a reasonable safety factor and without undue or objectionable deflection–the weight of the fully loaded machine and the forces transmitted by it during operation. Provide sufficient clearance for machine movement.
WARNING 2 : Entangle and Crush Hazards—Contact with moving components normally isolated by guards, covers, and panels, can entangle and crush your limbs. These components move automatically. • Do not remove guards, covers, or panels. • Do not reach into the machine housing or frame. • Keep yourself and others off of machine. • Know the location of all emergency stop switches, pull cords, and/or kick plates and use them in an emergency to stop machine motion. 3.
Safety—Divided Cylinder and Staph-Guard™ Washer-Extractors 5. 5.1. 5.1.1. Safety Alert Messages—Unsafe Conditions [Document BIUUUS14] Damage and Malfunction Hazards Hazards Resulting from Inoperative Safety Devices DANGER 7 : Entangle and Sever Hazards—Cylinder door interlock—Operating the machine with a malfunctioning door interlock can permit opening the door when the cylinder is turning and/or starting the cycle with the door open, exposing the turning cylinder.
5.2. 5.2.1. Careless Use Hazards Careless Operation Hazards—Vital Information for Operator Personnel (see also operator hazards throughout manual) WARNING 15 : Multiple Hazards—Careless operator actions can kill or injure personnel, damage or destroy the machine, damage property, and/or void the warranty. • Do not tamper with or disable any safety device or operate the machine with a malfunctioning safety device. Request authorized service. • Do not operate a damaged or malfunctioning machine.
About the Forces Transmitted by Milnor® Washer-extractors About the Forces Transmitted by Milnor® Washer-extractors Document ..................... BIWUUI02 Specified Date ................. 20001108 As-of Date ....................... 20001108 Access Date ..................... 20001108 Applicability...........................WUU During washing and extracting, all washer-extractors transmit both static and dynamic (cyclic) forces to the floor, foundation, or any other supporting structure.
has sufficient strength and rigidity, plus a reasonable factor of safety for both, to support the weight of all the fully loaded machine(s) including the weight of the water and goods, and including the published 360º rotating sinusoidal RMS forces that are transmitted by the machine(s). Moreover, the floor, foundation, or other supporting structure must have sufficient rigidity (i.e.
7\_ccQbi _V DQW 9\\ecdbQdY_^c± Cec`U^TUT GQcXUb 5hdbQSd_bc Illustration
Illustration Explanation Do not start this machine until the packing materials, lifting brackets, etc. with this tag attached or behind this panel are removed. These materials are painted red. Safety stands or brackets (also painted red) may be provided with this machine. Do not discard safety stands or brackets Do not step or stand on this machine part. Maintain a 25 mm. (1") minimum clearance between float clips.
7\_ccQbi _V DQW 9\\ecdbQdY_^c± Cec`U^TUT GQcXUb 5hdbQSd_bc Do not start this machine until the part with this tag is installed on the machine. Do not remove this component from the machine. Install the appropriate part here before operating the machine.
=C9E@ED715 " # "&F " # Do not pump grease here. During drain and extract, the cylinder must rotate counterclockwise when viewed from here (rear of machine). During drain and extract, the cylinder must rotate clockwise when viewed from here (front of machine). Do not strike shell front of washer-extractors during fork lifting. Striking shell front will cause door to leak. Brake assembly under machine is fragile.
7\_ccQbi _V DQW 9\\ecdbQdY_^c± Cec`U^TUT GQcXUb 5hdbQSd_bc Set main bearing air pad gauge at 10 psi (.70 kg/cm2), 64" and 72" ExN and JxN models only. Set disc brake air gauge at 10 psi (.70 kg/cm2), 64" and 72" ExN and JxN models only. Make cold water connection here. H20 Make hot water connection here. H20 Make third (reuse) water connection here.
=C9E@ED715 " # "&F # # Hold the connection side of the valve with a wrench when connecting plumbing.
BIWUUI03 (Published) Book specs- Dates: 20030306 / 20030306 / 20030306 Lang: ENG01 Applic: WUU Avoiding Damage From Allied Remote Chemical Delivery Systems Milnor® does not manufacture or supply remote chemical delivery systems and this document is meant only to illustrate some of the possible problems that can be minimized during installation of such systems by the chemical supply company.
Avoiding Damage From Allied Remote Chemical Delivery Systems Chemical products commonly found in the laundry industry, when used in established dosages and proper operating parameters, under the auspices of an experienced chemical specialist, should produce satisfactory results, with no consequential detrimental effects. The industry has published standards in Riggs and Sherrill, “Textile Laundering Technology”.
Figure 2: Siphoning From the Chemical Tank into the Machine Examples Legend P. S. T. 2.2. Pump Siphon level. Shading indicates the chemical delivery line and tank content that can siphon into the machine. Chemical tank Ensure the Chemical Lines Cannot Dribble—The pumped chemical system may provide a means of positively closing the chemical line at the pump location, but not at the injection site.
Avoiding Damage From Allied Remote Chemical Delivery Systems Figure 3: Dribbling From Chemical Supply Line Into Machine (assumes positive closure at the pump) Examples Legend D. P. T. 3. Portion of supply line, the contents of which can dribble into the machine Pump Chemical tank Design and Installation Recommendations It is the responsibility of the chemical system manufacturer and supplier to use whatever measures are necessary to ensure that their system is safe for personnel and equipment.
3.4. Dribbling: Locate the entire chemical line below the machine inlet.— Assuming the chemical system does not retain any line pressure and that the pump provides positive closure when the system is off, locate the entire chemical delivery line below the level of the chemical inlet. An example of this is shown in Figure 4. Figure 4: Locating a Pumped Chemical System With Positive Closure To Protect Against Machine Damage Example of Correct Placement Legend I. L. P. T. 4.
Section Service and Maintenance 23 1
MSSM0201CE/2004046V ÈUBRICATION AND PREVENTIVE MAINTENANCE L FOR HYDRO-CUSHION® MACHINES General Requirements Ê CRUSH/SEVER HAZARD—Tilting machines with tilt wheels/cradles may lunge forward or rearward and even fall over if the tilt wheels at the non-tilted end are raised out of their cradles—killing/injuring personnel and/or damaging property. Maintenance procedures require: ☞ NEVER manually tilt (lift) both ends of the machine at the same time. One end must always be seated in its cradle.
MSSM0201CE/2004046V (1 of 9) ÈUBRICATION AND PREVENTIVE MAINTENANCE L FOR HYDRO-CUSHION® MACHINES General Requirements Ê CRUSH/SEVER HAZARD—Tilting machines with tilt wheels/cradles may lunge forward or rearward and even fall over if the tilt wheels at the non-tilted end are raised out of their cradles—killing/injuring personnel and/or damaging property. Maintenance procedures require: ☞ NEVER manually tilt (lift) both ends of the machine at the same time. One end must always be seated in its cradle.
26 ÎFIGURE 3 (MSSM0201CE) ÎTypical Upper Hydro-Cushion® Grease Fitting Î IGURE 1 (MSSM0201CE) F ÎHydraulic Fluid Reservoir Fill and Level Check Point (located at rear of 48", 52", and 72" tilt machines only) ÎFIGURE 2 (MSSM0201CE) ÎTypical Hydro-Cushion® Maintenance Points Final stage and other v-belts (throughout all machines) FIGURES 1 and 12 NOTES 2 and 3 Hydro-Cushions® (all machines) FIGURES 2 and 3 Hydraulic Tilt System (48", 52", and 72" Tilt machines) • Reservoir FIGURE 1 and NOTE 1 Component
27 ÎFIGURE 6 (MSSM0201CE) Î42" Divided Cylinder Rear Bearing and Seal Grease Fittings ÎFIGURE 4 (MSSM0201CE) Î 2" Divided Cylinder Front 4 Bearing and Seal Grease Fittings ® 0.37 ounces (10.6 grams), six strokes at two locations 0.12 ounces (3.
28 ÎFIGURE 13 (MSSM0201CE) ÎHydrocushion Bypass Valve (48" machines only") Hydro-cushion bypass Î IGURE 10 (MSSM0201CE) F Î60044 and 72044 Staph-Guard® Rear Bearing and Seal Grease Fittings (lo- Î IGURE 12 (MSSM0201CE) F Î ypical Drive Train Components (48" machine shown) T Î IGURE 9 (MSSM0201CE) F Î60044 and 72044 Staph-Guard® Front Bearing and Seal Grease Fit- ÎFIGURE 11 (MSSM0201CE) ÎAll Open-Pocket Machine Seal and Bearing Grease Fitting Plate Action 0.06 ounces (1.
29 ÎFIGURE 17 (MSSM0201CE) Î42" Staph-Guard® ldler Shaft Grease Fitting ÎFIGURE 14 (MSSM0201CE) ÎHandwheel Screw (42" Divided Cylinder and Staph-Guard® only) ÎFIGURE 18 (MSSM0201CE) Î60" and 72" Staph-Guard® Idler Shaft and Disc Brake Grease Fittings (60" shown) ÎFIGURE 15 (MSSM0201CE) ÎTypical Door Hinge ÎFIGURE 19 (MSSM0201CE) ÎTypical Jackshaft Grease Fittings ( 52" machine shown) ÎFIGURE 16 (MSSM0201CE) ÎHandwheel Stop (42" Divided Cylinder and Staph-Guard® only)
30 ÎFIGURE 20 (MSSM0201CE) ÎTilt Wheels (42"and 48" tilt machines only) Ï 0.12 ounces (3.54 grams), two strokes at each location 0.06 ounces (1.77 grams), one stroke at one location 0.31 ounces (8.85 grams), five strokes at two locations 0.12 ounces (3.54 grams), two strokes at one location 0.12 ounces (3.54 grams) two strokes at two locations 0.12 ounces (3.
31 ÎFIGURE 24 (MSSM0201CE) ÎDisk Brake (Staph-Guard® only) Î IGURE 21 (MSSM0201CE) F ÎDisk Brake Reservoir (Staph-Guard® only) ÎFIGURE 25 (MSSM0201CE) Î ydraulic Tilt Pressure Gauge H (On rear of 42", 48", and 72" tilt models) ÎFIGURE 22 (MSSM0201CE) Î rake Band Grease Fittings B (60044 and 72044WP2/WP3) Brake band grease fittings ÎFIGURE 26 (MSSM0201CE) ÎDoor Seal Pressure Regulator ÎFIGURE 23 (MSSM0201CE) ÎBrake Shoes (all machines)
32 Component Check for wear, adjust or replace as required. Check for wear, replace as required • Brake shoes FIGURE 23 • Disc brake pads (60" and 72" Staph-Guard®only) FIGURE 24 Check pressure while machine is returning from a tilted position 800 PSI (55 Bar) 900 PSI (62 Bar) 1000 PSI (69 Bar) Check settings with machine in bare manual and clockwise wash rotation. See instructions for operating individual outputs in the reference manual. 48 - 50 PSI (3.37 - 3.51Kg/cm2) 25 - 28 PSI (1.76 - 1.
33 ÎFIGURE 28 (MSSM0201CE) ÎPush Back and Forward Hydraulic System Gauges and Regulators (42", 48", and 72" Tilt Models) ÎFIGURE 30 (MSSM0201CE) Î hell Door Recirculation Hose S (48" dye machine only - cover removed for clarity) Î IGURE 27 (MSSM0201CE) F ÎTypical Gear Reducer Fill and Drain ÎFIGURE 29 (MSSM0201CE) Î ush-Down Control Valve P (72" Rapid load and Staph-Guard® only) Component Hydraulic system FIGURE 28 Hydro-Cushions® FIGURE 2 Gear reducer FIGURE 27 Component Change oil Change oil C
34 52038WP1/WTL/WTN 64046ExN 72046ExN 72058JxN Divided Cylinder Machines 42031 - 44 WP2/3 42031 - 44 SP2/3 60044 SP2/3 72044 SP2/3 30015, 20, 22, C, S, and M 3022F8J 36021Q4x, 36026Q4x 36021BWP 36021Q6x, 36026Q6x, 42024Q4x, 42026Q6x 36030Fxx 42032Fxx 42026QHP 48032BHP/BTL/BTN 48036QHP/QTL/QTN Open Pocket Machines Bearing housings EPLF 2 EPLF 2 220 30 Gear reducers 220 220 220 Isolators 1030 1030 220 ® Hydro-Cushions 1030 EPLF 2 1030 220 Motors EPLF 2 Commutator cam Wells Balancing
21<4?B =?D?B =19>D5>1>35
21<4?B =?D?B =19>D5>1>35 =CC= "'$15 )'#!1F " $ 8_g d_ 4UdUb]Y^U
21<4?B =?D?B =19>D5>1>35 =CC= "'$15 )'#!1F # $ Table 3 — Recommended Lubrication Intervals at Standard Service Conditions NEMA (IEC) Frame Size Rated Speed - RPM 3600 1800 1200 900 Up to 215 (132) 5500 Hrs. 12000 Hrs. 18000 Hrs. 22000 Hrs. 254 to 286 (160 - 180) 3600 Hrs. 9500 Hrs. 15000 Hrs. 18000 Hrs. 324 to 365 (200 - 225) 2200 Hrs.(Note 3) 7400 Hrs. 12000 Hrs. 15000 Hrs. 404 to 5000 (280 - 315) 2200 Hrs.(Note 3) 3500 Hrs. 7400 Hrs. 10500 Hrs.
21<4?B =?D?B =19>D5>1>35 =CC= "'$15 )'#!1F $ $
39
General Assembly - WED R BMP701387R/71152A (Sheet 1 of 1) Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List—General Assembly - WED Description Item 6036 Part List 6044 7244 . ---------------------------------------------------------------------ASSEMBLIES-----------------------------------------------------------------1. Level Indicator Gasket, Outer 2 -18940 2-18940 2-18940 2. Sight Glass 2 -18657 2-18657 2-18657 3.
41
42
43
MSSM0101CE/9906AV (1 of 19) FASTENER TORQUE REQUIREMENTS È The specifications in this section apply to 1/4 inch and larger Unified National fine and coarse fasteners used on Milnor® machines. This information is to be used only when torque specifications are not stated in the installation or service instructions. When tightening applicable fastener, abide by the following precautions: 1. Always use new fasteners. Replace bolts, nuts, flat washers, and lock washers in the order shown on the parts drawing.
MSSM0101CE/9906AV (2 of 19) Applying Threadlocker Ê NOTE: The following threadlocker information and illustrations are excerpts from the Loctite® User’s Guide and are used with permission. For maximum strength, threadlocker must fill the thread voids completely, as shown in FIGURE 2. Organic or petroleum solvent will remove excess uncured adhesive from joints. Consult information below for the specific fastener application. ÎFIGURE 2 (MSSM0101CE) ÎCorrect Threadlocker Use Bolts and Nuts—See FIGURE 3. Ë 1.
FASTENER TORQUE REQUIREMENTS MSSM0101CE/9906AV (3 of 19) Removing Fasteners Ë High strength threadlockers like Loctite® 271 (or equivalent) may be weakened by heating to at least 500o F (260o C) as follows. 1. Apply localized heat to fastener as shown in FIGURE 5. 2. Disassemble while hot. Once disassembled, the cured adhesive can be removed with Loctite® Gasket Remover #790 (or equivalent).
MSSM0101CE/9906AV (4 of 19) ÏAll values in foot pounds and (Newton meters) NomiGrade Designation nal bolt and Standard size 1/4 - 28 Zinc or If instructions call for : Cadmium Loctite Loctite Loctite Plated 222 or 242 271 262 Loctite 272 Loctite 277 Bare SAE Grade 1 ASTM A307 2.8 (3.80) 3.4 (4.61) 3.8 (5.15) 4.1 (5.56) 5.3 (7.18) 4.9 (6.64) 3.8 (5.15) SAE Grade 2 4.7 (6.37) 5.6 (7.60) 6.3 (8.54) 6.9 (9.36) 8.8 (11.93) 8.1 (10.98) 6.3 (8.54) SAE Grade 4 5.5 (7.46) 6.6 (8.95) 7.3 (9.
FASTENER TORQUE REQUIREMENTS MSSM0101CE/9906AV (5 of 19) ÏAll values in foot pounds and (Newton meters) Nominal Grade Designation Zinc If instructions call for : bolt size and Standard orCadmium Loctite Loctite Loctite Plated 222 or 242 271 262 Loctite 272 Loctite 277 Bare 5/16 - 24 SAE Grade 1 ASTM A307 5.6 (7.59) 6.7 (9.08) 7.4 (10.03) 8.2 (11.12) 10.4 (14.10) 9.6 (13.01) 7.4 (10.03) SAE Grade 2 9.4 (12.74) 11.3 (15.32) 12.5 (16.94) 13.8 (18.71) 17.5 (23.73) 16.3 (22.09) 12.5 (16.
MSSM0101CE/9906AV (6 of 19) ÏAll values in foot pounds and (Newton meters) Nominal Grade Designation bolt size and Standard 3/8 - 24 Zinc or If instructions call for : Cadmium Loctite Loctite Loctite Plated 222 or 242 271 262 Loctite 272 Loctite 277 Bare SAE Grade 1 ASTM A307 10.2 (13.83) 12.2 (16.54) 13.6 (18.44) 15.0 (20.33) 19.0 (25.76) 17.7 (24.00) 13.6 (18.44) SAE Grade 2 16.9 (22.91) 20.3 (27.52) 22.5 (30.52) 24.8 (33.62) 31.5 (42.70) 29.3 (39.73) 22.5 (30.50) SAE Grade 4 20.
FASTENER TORQUE REQUIREMENTS MSSM0101CE/9906AV (7 of 19) ÏAll values in foot pounds and (Newton meters) Nominal Grade bolt size Designation and Standard Zinc or Cadmium Plated If instructions call for : Loctite 222 or 262 Loctite 242 Loctite 271 Loctite 272 Loctite 277 Bare 7/16 - 20 SAE Grade 1 ASTM A307 16.0 (21.70) 19.2 (26.03) 21.3 (28.88) 23.5 (31.86) 29.9 (40.54) 27.7 (37.56) 21.3 (28.88) SAE Grade 2 26.9 (36.48) 32.2 (43.66) 35.8 (48.54) 39.4 (53.42) 50.1 (67.93) 46.6 (63.
MSSM0101CE/9906AV (8 of 19) ÏAll values in foot pounds and (Newton meters) Nominal Standard and Zinc or bolt size Grade Designation Cadmium Plated 1/2 - 20 If instructions call for : Loctite 222 or 262 Loctite 242 Loctite 271 Loctite 272 Loctite 277 Bare SAE Grade 1 ASTM A307 24.8 (33.62) 29.8 (40.40) 33.1 (44.88) 36.4 (49.35) 46.4 (62.91) 43.1 (58.44) 33.1 (44.88) SAE Grade 2 41.3 (56.00) 49.5 (67.11) 55.0 (74.57) 60.5 (82.02) 77.0 (104.40) 71.5 (96.94) 55.0 (74.57) SAE Grade 4 48.
FASTENER TORQUE REQUIREMENTS MSSM0101CE/9906AV (9 of 19) ÏAll values in foot pounds and (Newton meters) Nominal Grade Designation bolt size and Standard Zinc or If instructions call for: Cadmium Loctite Loctite Loctite Plated 222 or 242 271 262 Loctite 272 Loctite 277 Bare 9/16 - 18 SAE Grade 1 ASTM A307 35.3 (47.86) 42.4 (57.49) 47.1 (63.86) 51.8 (70.23) 66.0 (89.48) 61.2 (82.98) 47.1 (63.86) SAE Grade 2 59.1 (80.13) 70.9 (96.13) 78.8 (106.84) 86.6 (117.41) 110.3 (149.55) 102.4 (138.
MSSM0101CE/9906AV (10 of 19) ÏAll values in foot pounds and (Newton meters) Nominal Grade Designation bolt size and Standard 5/8 - 18 Zinc or If instructions call for: Cadmium Loctite Loctite Loctite Plated 222 or 242 271 262 Loctite 272 Loctite 277 Bare SAE Grade 1 ASTM A307 49.5 (67.11) 59.4 (80.54) 66.0 (89.48) 72.6 (98.43) 92.4 (125.27) 85.8 (116.33) 66.0 (89.48) SAE Grade 2 82.6 (112.00) 99.1 (134.36) 110.2 (149.41) 121.2 (164.33) 154.2 (209.07) 143.2 (194.15) 110.2 (149.
FASTENER TORQUE REQUIREMENTS MSSM0101CE/9906AV (11 of 19) ÏAll values in foot pounds and (Newton meters) Nominal Grade Designation bolt size and Standard 3/4 - 16 Zinc or If instructions call for: Cadmium Loctite Loctite Loctite Plated 222 or 242 271 262 Loctite 272 Loctite 277 Bare SAE Grade 1 ASTM A307 86.5 (117.28) 103.8 (140.73) 115.3 (156.33) 126.8 (171.92) 161.4 (218.83) 149.9 (203.24) 115.3 (156.33) SAE Grade 2 144.1 (195.37) 173.0 (234.56) 192.2 (260.59) 211.4 (286.62) 269.
MSSM0101CE/9906AV (12 of 19) ÏAll values in foot pounds and (Newton meters) Nominal Grade Designation bolt size and Standard 7/8 - 14 Zinc or If instructions call for: Cadmium Loctite Loctite Loctite Plated 222 or 242 271 262 Loctite 272 Loctite 277 Bare SAE Grade 1 ASTM A307 137.8 (186.83) 165.4 (224.25) 183.8 (249.20) 202.1 (274.01) 257.3 (348.85) 238.9 (323.90) 183.8 (249.20) SAE Grade 2 137.8 (186.83) 165.4 (224.25) 183.8 (249.20) 202.1 (274.01) 257.3 (348.85) 238.9 (323.90) 183.
FASTENER TORQUE REQUIREMENTS MSSM0101CE/9906AV (13 of 19) ÏAll values in foot pounds and (Newton meters) Nominal Grade bolt size Designation and Standard 1 - 12 Zinc or Cadmium Plated If instructions call for : Loctite 222 or 262 Loctite 242 Loctite 271 Loctite 272 Loctite 277 Bare SAE Grade 1 ASTM A307 205.3 278.35 246.4 (334.07) 273.8 (371.22) 301.1 (408.24) 383.3 (519.69) 355.9 (482.54) 273.8 (371.22) SAE Grade 2 205.3 (278.35) 246.4 (334.07) 273.8 (371.22) 301.1 (408.24) 383.
MSSM0101CE/9906AV (14 of 19) ÏAll values in foot pounds and (Newton meters) Nominal Grade Designation bolt size and Standard Zinc or If instructions call for : Cadmium Loctite Loctite Loctite Plated 222 or 242 271 262 Loctite 272 Loctite 277 Bare 1-1/8 • 7 SAE Grade 1 ASTM A307 265.8 (360.37) 318.9 (432.37) 354.4 (480.50) 389.8 (528.50) 496.1 (672.62) 460.7 (624.63) 354.4 (480.50) SAE Grade 2 265.8 (360.37) 318.9 (432.37) 354.4 (480.50) 389.8 (528.50) 496.1 (672.62) 460.7 (624.63) 354.
FASTENER TORQUE REQUIREMENTS MSSM0101CE/9906AV (15 of 19) ÏAll values in foot pounds and (Newton meters) Nominal Grade Zinc or bolt size Designation and Cadmium Standard Plated 1-1/4 • 7 If instructions call for : Loctite 222 or 262 Loctite 242 Loctite 271 Loctite 272 Loctite 277 Bare SAE Grade 1 ASTM A307 375.0 (508.43) 450.0 (610.11) 500.0 (677.91) 550.0 (745.70) 700.0 (949.07) 650.0 (881.28) 500.0 (677.91) SAE Grade 2 375.0 (508.43) 450.0 (610.11) 500.0 (677.91) 550.0 (745.70) 700.
MSSM0101CE/9906AV (16 of 19) ÏAll values in foot pounds and (Newton meters) Nominal Grade Designation Zinc or bolt size and Standard Cadmium Plated If instructions call for : Loctite 222 or 262 Loctite 242 Loctite 271 Loctite 272 Loctite 277 Bare 1-3/8 • 6 SAE Grade 1 ASTM A307 491.1 (665.84) 589.4 (799.12) 654.8 (887.79) 720.3 916.8 851.3 654.8 (976.60) (1243.00) (1154.21) (887.80) SAE Grade 2 491.1 (665.84) 589.4 (799.12) 654.8 (887.79) 720.3 916.8 851.3 654.8 (976.60) (1243.00) (1154.
FASTENER TORQUE REQUIREMENTS MSSM0101CE/9906AV (17 of 19) ÏAll values in foot pounds and (Newton meters) Nominal Grade bolt size Designation and Standard Zinc or Cadmium Plated If instructions call for : Loctite 222 or 262 Loctite 242 Loctite 271 Loctite 272 Loctite 277 Bare 1-1/2 • 6 SAE Grade 1 ASTM A307 652.5 (884.67) 783.0 870.0 957.0 1218.0 1131.0 870.0 (1061.60) (1179.56) (1297.52) (1651.39) (1533.43) (1179.56) SAE Grade 2 652.5 (884.67) 783.0 870.0 957.0 1218.0 1131.0 870.0 (1061.
MSSM0101CE/9906AV (18 of 19) ÏOther Fastener Torque Specifications ÏAll values in foot-pounds and (Newton-meters) Nominal bolt size 18 - 8 Stainless Steel 316 Stainless Steel Brass Aluminum 2024 - T4 1/4 - 20 6.3 (8.54) 6.6 (8.95) 5.1 (6.91) 3.8 (5.15) 1/4 - 28 7.8 (10.57) 8.3 (11.25) 6.4 (8.67) 4.8 (6.50) 5/16 - 18 11.0 (14.90) 11.5 (15.60) 8.9 (12.06) 6.7 (9.08) 5/16 - 24 11.8 (16.00) 12.3 (16.67) 9.7 (13.15) 7.2 (9.76) 3/8 - 16 19.7 (26.71) 20.6 (27.93) 16.0 (21.70) 11.
FASTENER TORQUE REQUIREMENTS MSSM0101CE/9906AV (19 of 19) ÏOther Fastener Torque Specifications ÏAll values in foot-pounds and (Newton-meters) Nominal bolt size 18 - 8 Stainless Steel 316 Stainless Steel Brass Aluminum 2024 - T4 7/8 - 9 194.0 (263.03) 202.5 (274.55) 158.8 (215.30) 124.6 (168.93) 7/8 - 14 193.2 (261.94) 201.7 (273.47) 157.9 (214.08) 124.2 (168.40) 1-8 286.7 (388.71) 299.6 (406.20) 234.6 (318.07) 183.8 (249.20) 1 - 14 259.2 (351.43) 270.8 (367.16) 212.1 (287.57) 166.
Section Shell and Door Assemblies 63 2
MSSMA413AE/8530BV Location A—Seals must contact each other and shell front. È OOR SEAL REPLACEMENT ON D RAPID LOAD MODELS Door Seal Replacement Ê The seal components referred to herein are contained in kits K28 0005R (for 60" machines) or K36 0003R (for 72" machines). 1. Remove old seal from the door cavity and carefully pull air tubing out of inner door so as not to cut tubing. 2. Remove as much as possible of the old adhesive from the rubber filler strip inside door cavity.
MSSMA413AE/8530BV (1 of 2) Location A—Seals must contact each other and shell front. È OOR SEAL REPLACEMENT ON D RAPID LOAD MODELS Door Seal Replacement Ê The seal components referred to herein are contained in kits K28 0005R (for 60" machines) or K36 0003R (for 72" machines). 1. Remove old seal from the door cavity and carefully pull air tubing out of inner door so as not to cut tubing. 2. Remove as much as possible of the old adhesive from the rubber filler strip inside door cavity.
Check Condition of Door Seal Channel—Be certain the sides of the channel in which the door seal Ë Check Door Alignment In and Out—Misalignment of the doors in and out of the shell front opening can Ë fits are straight and that mainly the inner edge is not bent. See FIGURE 3 below. Because outer edge is double thickness it is not likely to be bent out of shape. But it is possible for the inner edge to become bent as shown. be most often attributed to worn striker plates as described above.
Check Condition of Door Seal Channel—Be certain the sides of the channel in which the door seal Ë Check Door Alignment In and Out—Misalignment of the doors in and out of the shell front opening can Ë fits are straight and that mainly the inner edge is not bent. See FIGURE 3 below. Because outer edge is double thickness it is not likely to be bent out of shape. But it is possible for the inner edge to become bent as shown. be most often attributed to worn striker plates as described above.
68
Door Assembly BMP790020R/98301V (Sheet 1 of 1) 7244WE3,SG Pellerin Milnor Corporation R P. O. Box 400, Kenner, LA 70063-0400 Litho in U.S.A. Parts List—Door Assembly Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In" column to identify which components belong to an assembly. The item numbers (1, 2, 3, etc.) assigned to components relate the parts list to the illustration. .
70
Shell Door Assembly BMP780109R/81433A (Sheet 1 of 2) 60 & 70 WEH Pellerin Milnor Corporation R P. O. Box 400, Kenner, LA 70063-0400 Litho in U.S.A. Parts List—Shell Door Assembly Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In" column to identify which components belong to an assembly. The item numbers (1, 2, 3, etc.) assigned to components relate the parts list to the illustration. Item .
BMP780109R/81433A (Sheet 2 of 2) R Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Item Used In Parts List, cont.—SHELL DOOR ASSEMBLY Part Number Description Comments all 24 02 175037 92452C HANDLE=SHELDOR=WED-SS all 25 53A500 1/4" SLEEVE-DELRIN all 26 53A059A NUT 1/4"COMP.
BMP810002/81073A AIR OPERATED VACUUM PUMP FOR DOOR SEALS MILNOR Rapid load door seals are now deflated with an air operated vacuum pump. The air operated vacuum pump quickly deflates the door seals when the stop button is pressed. Once the stop button is pressed a timer in the door circuit prevents the doors from being opened for 7-1/2 seconds. This allows the seals time to deflate before the doors are open. The air operated vacuum pump is mounted on the side of the main valve set.
74
Door Interlock - WED R BMP701654R/70481 (Sheet 1 of 1) Pellerin Milnor Corporation P. O. Box 400, Kenner, LA 70063-0400 Litho in U.S.A. Parts List—Door Interlock - WED Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In" column to identify which components belong to an assembly. The item numbers (1, 2, 3, etc.) assigned to components relate the parts list to the illustration. .
76 R 7 3 2 1 P. O.
Section Drive Assemblies 77 3
MSSMA407BE/85047V È RIVE BASE COMPONENTS ON D HYDRO-CUSHION® MACHINES General Description of Drive Mechanism Ê Wash motor E1 motor is optional on 42" and 48" machines and standard on larger models Major drive train components of the drive base include the following: Gear reducer E-1 motor 1. Drive motors: Wash, Drain, E-1 (low extract), E-2 (high extract) and Autospot. (The E1 motor is optional on 42" machines and standard on larger models except for 64" machines, which use one 2-speed extract motor.
MSSMA407BE/85047V (1 of 5) È RIVE BASE COMPONENTS ON D HYDRO-CUSHION® MACHINES General Description of Drive Mechanism Ê Wash motor E1 motor is optional on 42" and 48" machines and standard on larger models Major drive train components of the drive base include the following: Gear reducer E-1 motor 1. Drive motors: Wash, Drain, E-1 (low extract), E-2 (high extract) and Autospot.
To Replace Pulleys and Belt(s) Ë Motor, Belt, and Pulley Replacement Ê Part numbers for belts, pulleys, and related components may be found on the Drive Chart and/or Drive Assembly drawings for your machine. When ordering motors and motor parts from the Milnor® factory, provide the machine model and serial number and the motor function (i.e., wash, drain, E1 (low extract), E2 (high extract) or Autospot). Replacement rotors and bearings are available from Milnor® for some motors.
To Replace Pulleys and Belt(s) Ë Motor, Belt, and Pulley Replacement Ê Part numbers for belts, pulleys, and related components may be found on the Drive Chart and/or Drive Assembly drawings for your machine. When ordering motors and motor parts from the Milnor® factory, provide the machine model and serial number and the motor function (i.e., wash, drain, E1 (low extract), E2 (high extract) or Autospot). Replacement rotors and bearings are available from Milnor® for some motors.
the motor position with the motor mount (or other component) jack screws until all slack is taken up. Do not force belts onto the sheaves by using a pry bar or rolling the sheaves. 6. Check for sheave alignment as shown in FIGURES 3. The sheaves must be aligned within 1/64" per foot between shaft centerlines and in no case greater than 1/8". Readjust the sheave position as required to correct alignment. 7. Continue to alternately and progressively tighten cap screws to the “Final Torque” shown in the table.
the motor position with the motor mount (or other component) jack screws until all slack is taken up. Do not force belts onto the sheaves by using a pry bar or rolling the sheaves. 6. Check for sheave alignment as shown in FIGURES 3. The sheaves must be aligned within 1/64" per foot between shaft centerlines and in no case greater than 1/8". Readjust the sheave position as required to correct alignment. 7. Continue to alternately and progressively tighten cap screws to the “Final Torque” shown in the table.
It is essential when removing the gear reducer, to record the positions of these shims so that they may be replaced in the exact same position later. Bearing this in mind, carefully remove the gear reducer mounting bracket (with the reducer attached) from the drive base. Note that the clutch tire, attached to the reducer output shaft, must be allowed to slip out of the clutch drum as the reducer is removed. 4a. On 64" machine models only (i.e.
It is essential when removing the gear reducer, to record the positions of these shims so that they may be replaced in the exact same position later. Bearing this in mind, carefully remove the gear reducer mounting bracket (with the reducer attached) from the drive base. Note that the clutch tire, attached to the reducer output shaft, must be allowed to slip out of the clutch drum as the reducer is removed. 4a. On 64" machine models only (i.e.
To replace the jackshaft, reassemble all components in reverse order of their removal. Make certain that the jackshaft is properly oriented with the clutch end of the shaft to the front of the machine and that all shims are returned to their original positions. Install all jackshaft mounting bolts hand tight. Lift each end of the jackshaft with a pry bar (one end at a time) then tighten the bolts on that end, so that the jackshaft will sit as high as possible in the housing.
To replace the jackshaft, reassemble all components in reverse order of their removal. Make certain that the jackshaft is properly oriented with the clutch end of the shaft to the front of the machine and that all shims are returned to their original positions. Install all jackshaft mounting bolts hand tight. Lift each end of the jackshaft with a pry bar (one end at a time) then tighten the bolts on that end, so that the jackshaft will sit as high as possible in the housing.
88
Jackshaft Bearing Assembly BMP820109R/89253A (Sheet 1 of 2) 52, 60, 64, 72 Pellerin Milnor Corporation R Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List—Jackshaft Bearing Assembly Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In" column to identify which components belong to an assembly. The item numbers (1, 2, 3, etc.
BMP820109R/89253A (Sheet 2 of 2) R Pellerin Milnor Corporation P. O. Box 400, Kenner, LA 70063-0400 Item Used In Parts List, cont.
91
92 Used In Item Part Number Description A52 00300 SA 36 009 D52 00150 D52 00160 D36 00250 D36 00160 D36 00150 D36 00660 850562*DRIVE BASE ASSY 72WEU+WTU 910131*DRIVE ASSY=7244 WED 86521M* DRIVECHART 7244WT1 50CYC 86521M* DRIVECHART 7244WT1 60CYC 87202S*DRIVECHART=7244WE2 50CYC 87202S*DRIVECHART=7244WE2 60CYC 87202S*DRIVECHART=7244WE3 50CYC 87202S*DRIVECHART=7244WE3 60CYC X5 20111 X3 06039 7 7 used in U, V used in W, X,Y,Z 20 20 560470R6SK 560407R6P1 56Q3NS2S 17 all used in Y, Z 56Q5EM 17
93 R P. O.
94 R P. O. Box 400, Kenner, LA 70063-0400 Pellerin Milnor Corporation Reducer Air Seal Parts List—Reducer Air Seal Item Part Number Description Comments 54S012HC 54S015 54S022A 54S023B 54S025A B C D E F REDUCR 10.16:1 3210-600EC2 REDUCR 10.16:1 3210-375EC2 REDUCR 19.59:1 3220-300EC1 REDUCER 19.6 SKK/DOR 3220-60C REDUCER 15.4 DORRIS #1115-25HC REDUCER 15.
95 R 32 31 P. O. Box 400, Kenner, LA 70063-0400 Pellerin Milnor Corporation Autospot Drive Assembly 8 19 7 1 20 21 25 24 23 4 3 2 5 32 31 29 30 18 17 14 15 16 31 9 10 11 12 13 Litho in U.S.A.
BMP701411/2000133V (Sheet 2 of 2) R Pellerin Milnor Corporation P. O. Box 400, Kenner, LA 70063-0400 Litho in U.S.A. Parts List—Autospot Drive Assembly Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In" column to identify which components belong to an assembly. The item numbers (1, 2, 3, etc.) assigned to components relate the parts list to the illustration. Description Item Part Number Comments .
97 R 9 10 11 15 8 16 17 4 4 9 10 11 20 5 6 Main Drive Pulley BMP710043/96216V (1 of 1) NOTE: Belt guards not shown. 7. Sensing Unit=60" + 72" WE P. O.
98
99
100 R P. O. Box 400, Kenner, LA 70063-0400 Pellerin Milnor Corporation Centrifugal Switch Assembly Litho in U.S.A.
101 Used In Item Part Number Description Comments ADC11001 ADC14001 EDC14801 SAE13 001 SAE13 001A V W X Y Z 3621CPE,BWP,NSP 4226DA1, 64040/64050E6N 64046E6N/J6N/D6N Q6'S 3621/26+4226Q4'S, 3621Q'S MANUFACTURED AFTER JAN.
102
MSSM0301AE/9126BV V-BELT TENSION ADJUSTMENTS È 1. Place a straight edge along the top edge of the belt to be tested so that it spans both pulleys. Place the tension tester in the center of the belt and press down on the cap until the lower o-ring is in line with the straight edge, as shown. This instruction is to be used for adjusting the belt tension on the following machine models: 42031WE2 42031SG2 42031WE3 42031SG3 42044WE2 42044SG2 42044WE3 42044SG3 Belt Tension Measurements Ê 2.
MSSM0301AE/9126BV (1 of 1) V-BELT TENSION ADJUSTMENTS È 1. Place a straight edge along the top edge of the belt to be tested so that it spans both pulleys. Place the tension tester in the center of the belt and press down on the cap until the lower o-ring is in line with the straight edge, as shown. This instruction is to be used for adjusting the belt tension on the following machine models: 42031WE2 42031SG2 42031WE3 42031SG3 42044WE2 42044SG2 42044WE3 42044SG3 Belt Tension Measurements Ê 2.
MSSMA405AE/8737BV Belt Tension Measurements Ê È-BELT TENSION ADJUSTMENTS V FOR 48", 52", 60" AND 72" WASHER-EXTRACTORS Unbanded Belts Ë 1. Place a straight edge along the top edge of the belt to be tested so that it spans both pulleys. Place the tension tester in the center of the belt and press down on the cap until the lower o-ring is in line with the straight edge, as shown. This instruction is to be used for adjusting the belt tension on the following machine models: 48036QHE 48036QTG 48036QTH 2.
MSSMA405AE/8737BV (1 of 2) È-BELT TENSION ADJUSTMENTS V FOR 48", 52", 60" AND 72" WASHER-EXTRACTORS Unbanded Belts Ë 1. Place a straight edge along the top edge of the belt to be tested so that it spans both pulleys. Place the tension tester in the center of the belt and press down on the cap until the lower o-ring is in line with the straight edge, as shown.
Tensioning Banded Belts Ë Ï Ï48032BHE, BTG, BTH Belt Deflect. (inches) 48036QHE, QTG, QT Initial Tension (lbs.) (ref.) Initial Tension (lbs.) (ref.) Belt Deflect (in.) Initial Tension (lbs.) (ref.) Ï48032BHE, BTG, BTH Initial Tension (lbs.) (ref.) Belt Deflect. (inches) 48036QHE, QTG, QT Initial Tension (lbs.) (ref.) Initial Tension (lbs.) (ref.) Belt Deflect (in.) Initial Tension (lbs.) (ref.) Initial Tension (lbs.) (ref.) WASH/ 2 SPEED WASH 9/32 6.6 - 9.2 KP3 5.1 - 7.1 KN 5/16 5.
Tensioning Banded Belts Ë Ï Ï48032BHE, BTG, BTH Belt Deflect. (inches) 48036QHE, QTG, QT Initial Tension (lbs.) (ref.) Initial Tension (lbs.) (ref.) Belt Deflect (in.) Initial Tension (lbs.) (ref.) Ï48032BHE, BTG, BTH Initial Tension (lbs.) (ref.) Belt Deflect. (inches) 48036QHE, QTG, QT Initial Tension (lbs.) (ref.) Initial Tension (lbs.) (ref.) Belt Deflect (in.) Initial Tension (lbs.) (ref.) Initial Tension (lbs.) (ref.) WASH/ 2 SPEED WASH 9/32 6.6 - 9.2 KP3 5.1 - 7.1 KN 5/16 5.
Section Bearing Assemblies 109 4
MSSM0303AE/8451BV È AIN BEARING AND SEAL REPLACEMENT M FOR DIVIDED CYLINDER MACHINES This section applies to the front and rear cylinder shaft bearings of all divided cylinder machines (Rapid Load, Staph-guard®, dye machines, etc.). It does not apply to jackshaft bearings, idler shaft bearings or bearings on open pocket machines. The bearings covered by this section are double row, spherical roller, self aligning bearings; Koya, SKF, FMC, Torrington or equal.
MSSM0303AE/8451BV (1 of 5) È AIN BEARING AND SEAL REPLACEMENT M FOR DIVIDED CYLINDER MACHINES This section applies to the front and rear cylinder shaft bearings of all divided cylinder machines (Rapid Load, Staph-guard®, dye machines, etc.). It does not apply to jackshaft bearings, idler shaft bearings or bearings on open pocket machines. The bearings covered by this section are double row, spherical roller, self aligning bearings; Koya, SKF, FMC, Torrington or equal.
inspection plate and use a timber to pry up the cylinder to remove cylinder weight from the bearings. Once the bearing is removed, the cylinder drops only approximately 1/32" before the shaft comes to rest on the shaft support. 4. Slide the bearing off of the shaft and if it is to be reused, place it on a clean surface and cover with a clean, lint free cloth.
inspection plate and use a timber to pry up the cylinder to remove cylinder weight from the bearings. Once the bearing is removed, the cylinder drops only approximately 1/32" before the shaft comes to rest on the shaft support. 4. Slide the bearing off of the shaft and if it is to be reused, place it on a clean surface and cover with a clean, lint free cloth.
Replacing the Bearing Housing, Seal Sleeve, Ê and Seals (Front or Rear) 1. With the seal sleeve removed, press all old seals out of the bearing housing. Remove the large o-ring from the outside of the housing. Thoroughly clean the bearing housing and flush out all grease passages to make certain they are unblocked. Remove the o-rings from the inside of the seal sleeve and clean the seal sleeve. 2. While the bearing housing is dissassembled, charge all grease passages with grease.
Replacing the Bearing Housing, Seal Sleeve, Ê and Seals (Front or Rear) 1. With the seal sleeve removed, press all old seals out of the bearing housing. Remove the large o-ring from the outside of the housing. Thoroughly clean the bearing housing and flush out all grease passages to make certain they are unblocked. Remove the o-rings from the inside of the seal sleeve and clean the seal sleeve. 2. While the bearing housing is dissassembled, charge all grease passages with grease.
Measuring Unmounted Clearance and Ê Setting Bearing (Front or Rear) The bearings used on Milnor® washer and dye extractors are the very best anti-friction devices available for these applications. However, the anti-frictional characteristics of the bearings will be reduced if they are not properly installed.
Measuring Unmounted Clearance and Ê Setting Bearing (Front or Rear) The bearings used on Milnor® washer and dye extractors are the very best anti-friction devices available for these applications. However, the anti-frictional characteristics of the bearings will be reduced if they are not properly installed.
Tightening Bearing(s) (Front and/or Rear) Ê 1. Once both bearings are seated, or if only one bearing was replaced, install the bearing lockwasher(s) and locknut(s). Use a hammer and a metal drift as shown in FIGURE 11, to tighten the locknut. It is imperative to only tap lightly and to assure that metal chips from the drift or locknut do not fall off and contaminate the bearing.
Tightening Bearing(s) (Front and/or Rear) Ê 1. Once both bearings are seated, or if only one bearing was replaced, install the bearing lockwasher(s) and locknut(s). Use a hammer and a metal drift as shown in FIGURE 11, to tighten the locknut. It is imperative to only tap lightly and to assure that metal chips from the drift or locknut do not fall off and contaminate the bearing.
120
121 BMP840039R/96142V (1 of 2) Parts List—60036, 60044 & 72044 WE2, WE3, SG2, SG3, & DA3 P. O.
BMP840039R/96142V (Sheet 2 of 2) R Pellerin Milnor Corporation P. O. Box 400, Kenner, LA 70063-0400 Litho in U.S.A. Parts List, cont.—60036, 60044 AND 72044 WE2, WE3, SG2, SG3, AND DA3 Item Used In Part Number Description Comments all all all 32 33 34 15B243 15K236 15K162 HEXCAPSCR 1-8X2+1/2 GR5 ZINC 05Z SKCPSCR 1-8 3X 2.75BLK-HK HXCAPSCR 1/2-13UNC2AX1.5 GR5 PLATED 72044SG2+3 all 34 15K162 HXCAPSCR 1/2-13UNC2AX1.
Section Frame, Pivots, and Suspension 123 5
124
Hold Down Adjustments 60" & 72" Rapid Load and Staph-Guard R Pellerin Milnor Corporation P. O. Box 400, Kenner, LA 70063-0400 BMP701672R/71051 (Sheet 1 of 1) Litho in U.S.A. Parts List—Hold Down Adjustments Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In" column to identify which components belong to an assembly. The item numbers (1, 2, 3, etc.
MSSM0302AE/8414BV ÈUSPENSION ADJUSTMENTS FOR S DIVIDED CYLINDER MACHINES ® ® The suspension system on Milnor Hydro-cushion machines is adjusted and thoroughly tested at the factory. It should not require subsequent adjustment unless the machine is distorted during shipment or installation or unless some component of the system, such as a Hydro-cushion® cylinder is replaced. There are two primary objectives when adjusting the suspension system on any Hydro-cushion® machine model: 1.
MSSM0302AE/8414BV (1 of 3) ÈUSPENSION ADJUSTMENTS FOR S DIVIDED CYLINDER MACHINES ® ® The suspension system on Milnor Hydro-cushion machines is adjusted and thoroughly tested at the factory. It should not require subsequent adjustment unless the machine is distorted during shipment or installation or unless some component of the system, such as a Hydro-cushion® cylinder is replaced. There are two primary objectives when adjusting the suspension system on any Hydro-cushion® machine model: 1.
Shell Hanging Dimensions and Adjustment Procedures Ê To adjust the shell of a divided cylinder machine, proceed as follows: Push-Down Travel Dimensions and Ê Adjustment Procedures 1. Locate the shell hanging dimension for your machine in the table below and adjust your machine accordingly. Take measurements on the left and right sides of the shell, to assure that the shell is horizontal, left to right. 2. The shell and cylinder should be level front to back.
Shell Hanging Dimensions and Adjustment Procedures Ê To adjust the shell of a divided cylinder machine, proceed as follows: Push-Down Travel Dimensions and Ê Adjustment Procedures 1. Locate the shell hanging dimension for your machine in the table below and adjust your machine accordingly. Take measurements on the left and right sides of the shell, to assure that the shell is horizontal, left to right. 2. The shell and cylinder should be level front to back.
5. With the shell pushed down, attempt to pull each test shim out from between the bracket and rubber pad. The test shims should all be tight. If any shim(s) are not pinched tightly between the bracket and pad, take note of which one(s) are not. Make final adjustments as follows: 6. Set the Master switch to off, remove the test shims and make the necessary changes to the shims below the rubber pads as indicated by the above test. 7. Repeat Steps 3 through 6 as required, until this test is successful. 8.
5. With the shell pushed down, attempt to pull each test shim out from between the bracket and rubber pad. The test shims should all be tight. If any shim(s) are not pinched tightly between the bracket and pad, take note of which one(s) are not. Make final adjustments as follows: 6. Set the Master switch to off, remove the test shims and make the necessary changes to the shims below the rubber pads as indicated by the above test. 3.
132
Suspension Cylinder Assembly R Pellerin Milnor Corporation P. O. Box 400, Kenner, LA 70063-0400 BMP701629R/73261A (Sheet 1 of 2) Litho in U.S.A. Parts List—Suspension Cylinder Assembly Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In" column to identify which components belong to an assembly. The item numbers (1, 2, 3, etc.) assigned to components relate the parts list to the illustration. .
BMP701629R/73261A (Sheet 2 of 2) Pellerin Milnor Corporation R P. O. Box 400, Kenner, LA 70063-0400 Used In Item 031 031 032 032 033 034 035 036 037 038 039 040 041 042 043 044 045 046 047 048 Parts List, cont.
Suspension Cylinder Locations BMP701235/2000133V (Sheet 1 of 1) Use with BMP701408 R Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Note: A letter is stamped on the end of the upper bolt to designate the cylinder assembly.
136
Push Down Assembly R BMP701671R/70526 (Sheet 1 of 1) Pellerin Milnor Corporation P. O. Box 400, Kenner, LA 70063-0400 Litho in U.S.A. Parts List—Push Down Assembly Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In" column to identify which components belong to an assembly. The item numbers (1, 2, 3, etc.) assigned to components relate the parts list to the illustration. .
138
Cylinder Assembly BMP790019R/86387A (Sheet 1 of 2) 7244 WE3 Pellerin Milnor Corporation R P. O. Box 400, Kenner, LA 70063-0400 Litho in U.S.A. Parts List—Cylinder Assembly Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In" column to identify which components belong to an assembly. The item numbers (1, 2, 3, etc.) assigned to components relate the parts list to the illustration. Item .
BMP790019R/86387A (Sheet 2 of 2) R Pellerin Milnor Corporation P. O. Box 400, Kenner, LA 70063-0400 Item Used In Parts List, cont.—Cylinder Assembly Part Number Description Litho in U.S.A.
141
P/L CYLINDER ASSEMBLY BMP780043R/86387A (Sheet 1 of 2) 60 & 70 WE2 Pellerin Milnor Corporation R P. O. Box 400, Kenner, LA 70063-0400 Litho in U.S.A. Parts List—P/L CYLINDER ASSEMBLY Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In" column to identify which components belong to an assembly. The item numbers (1, 2, 3, etc.) assigned to components relate the parts list to the illustration. Item .
BMP780043R/86387A (Sheet 2 of 2) R Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Item Used In Parts List, cont.
144
Section Control and Sensing Devices 145 6
MSSMA408BE/9273BV VIBRATION SAFETY SWITCH ADJUSTMENTS È B B What the Vibration Safety Switch Does Ë The vibration safety switch pictured below is an important safety feature. If properly adjusted, the switch will momentarily actuate as a result of repeated machine movement caused by an out-of-balance condition. Table A below illustrates the effect of the vibration safety switch actuation.
MSSMA408BE/9273BV (1 of 1) VIBRATION SAFETY SWITCH ADJUSTMENTS È B B What the Vibration Safety Switch Does Ë The vibration safety switch pictured below is an important safety feature. If properly adjusted, the switch will momentarily actuate as a result of repeated machine movement caused by an out-of-balance condition. Table A below illustrates the effect of the vibration safety switch actuation. that it has reset.
148
Vibration Switch Assembly R BMP700613R/83211A (Sheet 1 of 1) Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List—Vibration Switch Assy. Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In" column to identify which components belong to an assembly. The item numbers (1, 2, 3, etc.) assigned to components relate the parts list to the illustration. Item .
BMP750047/81307A MAINTENANCE - VIB SAFETY SWITCH The vibration safety switch will shut off the machine if properly adjusted. The unit consists of a sensitive micro switch having a long extended actuating arm on which is mounted on eccentric weight. The weight may be adjusted both by moving it up and down on the arm, and also by rotating it on the arm. In addition, the micro switch itself may be turned from side to side.
Section Chemical Supply Devices 151 7
MSSM0213AE /89457V (1 of 2) È ULES FOR THE FIELD INSTALLATION OF R PUMPED-TYPE LIQUID SUPPLY SYSTEMS APPLICABILITY: All Washer-Extractor Models GENERAL Ê Pellerin Milnor Corporation does not guarantee machines against damage from corrosion caused by improper installation and/or operation of pumped-type liquid supply systems. The following precautions must be observed when pumps are used: 1. Always install the pumping unit lower than the discharge end of the chemical delivery tube as shown at right.
RULES FOR THE FIELD INSTALLATION OF PUMPED-TYPE LIQUID SUPPLY SYSTEMS MSSM0213AE/89457V (2 of 2) of the tube after the pump stops will be diluted by the water remaining in the cup. 3. Never inject any concentrated chemical directly onto any metal, rubber, or plastic surface of the machine other than the plastic cups provided. It is not enough to merely inject the chemical onto a surface that will be subsequently flushed or wetted sometime during the wash process.
154
72" Supply Injector Assembly Pellerin Milnor Corporation R P. O. Box 400, Kenner, LA 70063-0400 BMP701401R/83173A (Sheet 1 of 1) Litho in U.S.A. Parts List—72" Supply Injector Assembly Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In" column to identify which components belong to an assembly. The item numbers (1, 2, 3, etc.) assigned to components relate the parts list to the illustration. Item .
156
Section Water and Steam Piping and Assemblies 157 8
158
Water Inlet Assembly R BMP701634R/71521A (Sheet 1 of 2) Pellerin Milnor Corporation P. O. Box 400, Kenner, LA 70063-0400 Litho in U.S.A. Parts List—Water Inlet Assembly Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In" column to identify which components belong to an assembly. The item numbers (1, 2, 3, etc.) assigned to components relate the parts list to the illustration.
160 R P. O. Box 400, Kenner, LA 70063-0400 Pellerin Milnor Corporation BMP920005/96067V (1 of 3) Universal Actuators & Mounting Hardware for Watts Ball Valves - New Pivot 3) ASSEMBLE SO THAT THE LINKAGE IS FREE TO MOVE IN THE SPACER, THIS MEANS THAT THERE SHOULD BE DAYLIGHT BETWEEN THE CRANK AND EACH ADJACENT WASHER WITHOUT EXCESSIVE CLEARANCE. 2) FOR 90 DEGREE VALVE SET, VALVE IS ROTATED 90 DEGREES. 1)RIGHT HAND ASSEMBLY IS SHOWN, LEFT HAND ASSEMBLY IS OPPOSITE. NOTES: Litho in U.S.A.
161 P. O. Box 400, Kenner, LA 70063-0400 Pellerin Milnor Corporation BMP920005/96067V (2 of 3) Item Part Number Description Comments 96D085BCSL 96D085BCSR 96D085BOSL 96D085BOSR 96D085SOSR 96D085SCSR 96D086BCSL 96D086BCSR 96D086BOSL 96D086BOSR 96D086SCNR 96D086SCSL 96D086SCSR 96D086SOSL 96D086SOSR 96D087BCSL 96D087BCSR 96D087BOSR 96D087SCNR 96D087SCSR 96D087SOSR 96D088BCSR 96D088BCNR 96D088BCSL 96D088BOSR 96D088SCNR 96D088SCSR 96D088SOSR 96D088BCNL 96D088BOSL 96D088SCSL 96D088SOSL 92000Z 1.
BMP920005/96067V (Sheet 3 of 3) R Pellerin Milnor Corporation P. O. Box 400, Kenner, LA 70063-0400 Litho in U.S.A. Parts List, cont.—Universal Actuators & Mounting Hardware for Watts Ball Valves Item Used In Part Number Description all 11 15G126 01Z HXLOCKNUT NYLON 10-24 UNC SS NM all all 12 13 15N159 15G170 HEXCAPSCR 1/4-2OUNC2AX7/16 18-8SS HEXNUT 1/4-20UNC2 SS18-8 AA-AF,BE, CD,DA-DL BA-BD, BF-BJ, CA-CC,CE, CF 14 07 20703D 89354B WASHER=2.00"WATTS CRANK 14 07 20703C 89354B WASHER=1.
163 P. O. Box 400, Kenner, LA 70063-0400 Pellerin Milnor Corporation BMP920007/96067V (1 of 2) 3 SEE NOTE BODY SEAL ADAPTER THRUST WASHER PACKING HANDLE STEM (BK) 3 5 NO REPAIR KITS NO REPAIR KITS 3/4",1" BRONZE DETAIL OLD STYLE STEM PACKING NUT SEAL (SSK) SEE NOTE.
164 Parts List—Watts Ball Valves and Repair Kits P. O.
165 R 5. Unscrew and remove adjusting screw, check nut, and spring cage screws. Lift off spring cage, spring washer and adjusting spring. 4. While disassembled open gate valve to flush out collected sediment. 8. To reassemble valve follow above instructions in reverse. Tighten or loosen adjusting screw for the required pressure of 28 P.S.I. 7. Lift stem assembly upwards to remove from body. 6. Loosen and remove lock nut, washer, plate, and diaphragm. 4.
BMP900031/96081V (Sheet 2 of 2) R Pellerin Milnor Corporation P. O. Box 400, Kenner, LA 70063-0400 Litho in U.S.A. Parts List—Pressure Regulators Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In" column to identify which components belong to an assembly. The item numbers (1, 2, 3, etc.) assigned to components relate the parts list to the illustration. Item .
167 R P. O. Box 400, Kenner, LA 70063-0400 Pellerin Milnor Corporation Water Level Float Chamber Parts List—Water Level Float Chamber Item Part Number Description Comments A03 03100 ALL11001 A14 07200C ALL48001 AD 14 046 AD 15 047 ALL11000 G28 18700A G36 07500A G25 02600A GLL64002 ALL64002 FLOAT CHMBR ASSY=8.25"CLDCON *FLOAT CHAMBER INSTAL=4226QHE $ ASSY=FLOAT SPRAY 42DAZ *FLOAT CHAMBER ASSY 4832-36 *FLOAT CHMBR INSTAL=35#+60#W FLOAT CHMBR 25.25ASY=42+72WE *FLOAT CHMBR 33.
168 26 26 27 27 27 27 30 31 alL AlL alL alL alL alL alL 24 alL alL 23 alL 26 22 alL alL 21 alL 26 20 alL alL 19 alL 25 18 alL alL 17 alL Used In R Item Description NPT RED 1X1/4 GALMAL 150# NPTELB 90DEG 1/4 BRASS 125# SA 02 011B SA 02 011 03 25298A 08 01065 02 15649 02 10505 03 25298A 02 15649 02 15663 02 10506 27A003 53A008B 12P014KK 51V015 *FLOAT ASSY L=66" 42DA+52DYA *FLOAT ASSY L=25"-STD LEVEL FLOAT CHAMBER BRACK BRACKET=LEVEL CNTRL MT 90DEG
WATER LEVEL FLOAT CHAMBER ASSEMBLY R Pellerin Milnor Corporation P. O. Box 400, Kenner, LA 70063-0400 BMP810111R/89256A (Sheet 1 of 2) Litho in U.S.A. Parts List—WATER LEVEL FLOAT CHAMBER Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In" column to identify which components belong to an assembly. The item numbers (1, 2, 3, etc.) assigned to components relate the parts list to the illustration. Item .
BMP810111R/89256A (Sheet 2 of 2) R Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List, cont.—WATER LEVEL FLOAT CHAMBER Item Used In Part Number Description Comments alL 13 5N0K04AG42 NPT NIPPLE 1/2X4 TBE GALSTL SK40 COOLDOWN OPT. alL 14 5SR0K0CNF NPT RED 1/2X1/8 GALMAL 150# COOLDOWN OPT.
171 R Notes: 1. Disconnect power at main switch before operating this enclosure. 2. Wiring must not interfere with movement of item 8. 3. To order complete water level switch assembly, see items A-G. 4. When item 20 is used in assembly G, flange will be on top (shown). When item 20 is used in assembly F, flange will be on bottom. P. O.
172
Stainless Steel Dump Valve Assembly R BMP701370R/72431A (Sheet 1 of 1) Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List—S/S Dump Valve Assembly Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In" column to identify which components belong to an assembly. The item numbers (1, 2, 3, etc.) assigned to components relate the parts list to the illustration.
174 R 3 P. O. Box 400, Kenner, LA 70063-0400 Pellerin Milnor Corporation Burket Steam Valve 2 1 BMP800020/96066V (1 of 1) Parts List—Burket Steam Valve Item Part Number Description Comments 96D0011ER1 96D0011ER2 96D0011ER3 X Y Z REPAIR KIT MULLER 1.25 VALVE #554 ACTUATOR HOUSING FOR BURKET #251 02Z REPAIR KIT 1.
175 ASS14001 ASS25001 ASS52001 ASS52001D ASS65001 ASS29001 NOTE: TO DETERMINE ASSEMBLY NUMBER FOR YOUR MACHINE SEE REVERSE SIDE ASS64001 STEAM SPARGER ASSEMBLIES ASS60005A - (3/4" ORIFICE) ASS60006A - (1/2" ORIFICE) ASS60007A - (3/4" ORIFICE) ASS60008A - (1/2" ORIFICE) BMP900001/96132V (Page 1)
176 ASS14001 ASS25001 ASS52001 ASS52001D ASS29001 ASS64001 ASS64001A ASS65001 ASS60005A ASS60006A ASS60007A ASS60008A W2 14628A W3 64566B W2 19565A W3 64564 W3 64564A 02 11369D 00A 00B 00C 00D 00E 00F 00FF 00G 00H 00I 00J 00K 001A 001B 002 003 004 005 92612T*ASSY=STM MIXER .5 ORF-21.5"L 92612#*ASSY=STM MIXER .75 ORF-21.5L 95496#*WLM=STM SPARGER .63 ORF-12"L 95496C*WLM=STM SPARGER .75 ORF-12"L 92637Y*WLM=STM SPARGER .
Section Pneumatic Piping and Assemblies 177 9
178 R P. O.
179 R P. O. Box 400, Kenner, LA 70063-0400 Pellerin Milnor Corporation Applicable Models Asco 3-way Solenoid Valves BMP701359/97086V (1 of 2) Identification and Description Remove retaining clip. NOTE: When metal retaining clip disengages, it springs upwards. Slip yoke containing coil and sleeves off solenoid base sub-assembly. Replace coil. Reassemble in reverse order. Troubleshooting Remove retaining clip. Slip entire solenoid enclosure off the solenoid base sub-assembly.
180 Parts List—Asco 3-way Solenoid Valves P. O.
181
182
183
P/L UNIVERSAL AIRVALVE BOX R Pellerin Milnor Corporation P. O. Box 400, Kenner, LA 70063-0400 BMP780088R/93046N (Sheet 1 of 2) Litho in U.S.A. Parts List—P/L UNIVERSAL AIRVALVE BOX Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In" column to identify which components belong to an assembly. The item numbers (1, 2, 3, etc.) assigned to components relate the parts list to the illustration. Item .
BMP780088R/93046N (Sheet 2 of 2) R Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List, cont.—P/L UNIVERSAL AIRVALVE BOX Item Used In Part Number Description all 24 96J019E 1/4"PRESSREG2-50PSI #R07-200-RNEA all 25 30N095 03Z PRESSGAUGE 1/8"BACKCONN 0-15PS1 all 26 5N0E03KBE2 NPT NIPPLE 1/4X3.5 TBE BRASS 125# all 27 5S0EBEA0G NPT TEE 1/4X1/4X3/8 BRASS 125# all 28 5SL0EBEC NPT ELBOW 90DEG STRT 1/4" BRASS 125 all 29 27A090 HOSECLAMP,11/16-1.
186
Air Valves & Mounting Hardware R Pellerin Milnor Corporation P. O. Box 400, Kenner, LA 70063-0400 BMP780087R/83457A (Sheet 1 of 2) Litho in U.S.A. Parts List—Air Valves & Mounting Hardware Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In" column to identify which components belong to an assembly. The item numbers (1, 2, 3, etc.) assigned to components relate the parts list to the illustration.
BMP780087R/83457A (Sheet 2 of 2) R Pellerin Milnor Corporation P. O. Box 400, Kenner, LA 70063-0400 Litho in U.S.A. Parts List, cont.—Air Valves & Mounting Hardware Item Used In Part Number Description all 15 96V350 1/4" VALVEBODY ASCO #UFTX8320A89 all 16 03 01523 85096C BRKT=LOCK AIR VALVE all 17 53A005B BODY=MALECONN 1/4X1/8COMP #B68A-4A all 18 53A059 SLEEVE 1/4" COMP IMP #60F BRASS all 19 53A059A NUT 1/4"COMP.
MSSM0130AE/9313AV SERVICING AIR CYLINDERS È 4. Loosen nuts on threaded rods evenly, permitting cylinder heads to separate. Use only a few turns on one nut before moving to the other one. Continue until springs have no tension. This is the general procedure for rebuilding an air cylinder using a Milnor® furnished repair kit, once the air cylinder has been removed from the machine.
MSSM0130AE/9313AV (1 of 1 ) SERVICING AIR CYLINDERS È 4. Loosen nuts on threaded rods evenly, permitting cylinder heads to separate. Use only a few turns on one nut before moving to the other one. Continue until springs have no tension. This is the general procedure for rebuilding an air cylinder using a Milnor® furnished repair kit, once the air cylinder has been removed from the machine.
191 R P. O. Box 400, Kenner, LA 70063-0400 Pellerin Milnor Corporation Air Cylinders for 2" Watts Ball Valves Litho in U.S.A.
192 Parts List—Air Cylinders for 2" Watts Ball Valves P. O. Box 400, Kenner, LA 70063-0400 Pellerin Milnor Corporation Item Part Number Description 17 17 18 18 A,B C,D SA 10 057C SA 10 057D SA 10 056F SA 10 056G 95222D AIRCYL=3.0ODX3.89ST171/176CD 95222# AIRCYL=3.0ODX3.89ST171/176SS 92000Z AIRCYL=2.38ODX2.70STX20.5#CD 92000Z AIRCYL=2.38ODX2.70STX20.
193
Long Air Cylinder Assembly Pellerin Milnor Corporation R P. O. Box 400, Kenner, LA 70063-0400 BMP701660R/89111A (Sheet 1 of 2) Litho in U.S.A. Parts List—Long Air Cylinder Assembly Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In" column to identify which components belong to an assembly. The item numbers (1, 2, 3, etc.) assigned to components relate the parts list to the illustration. Item .
BMP701660R/89111A (Sheet 2 of 2) R Pellerin Milnor Corporation P. O. Box 400, Kenner, LA 70063-0400 Item Used In Parts List, cont.—Long Air Cylinder Assembly Part Number Description all 29 5SB0E0CBEO HEXPIPBUSH 1/4 X 1/8 BRASS 125# all 30 20L601T ID TAG NAT'L #1614 ALUM EMB LET "T" 195 Litho in U.S.A.
196 P. O. Box 400, Kenner, LA 70063-0400 Pellerin Milnor Corporation NOTE: THE GOYEN VALVE MAY BE REPLACES BY EITHER THE WABCO OR DELTROL VALVE. NOTE: ASCO VALVES ARE USED PRIOR TO NOVEMBER 1987. SINCE THEN PARKER VALVES HAVVE BEEN USED IN PLACE OF THE ASCO. THE GOYEN VALVE IS NOT TO BE USED IN PLACE OF THE WABCO OR DELTROL VALVE. GOYEN (E) WABCO (B) ASCO (D) DELTROL (A) R Quick Exhaust Valves PARKER (C) Litho in U.S.A.
BMP701406/2002382V (Sheet 2 of 2) Pellerin Milnor Corporation R Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List—Quick Exhaust Valves Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In" column to identify which components belong to an assembly. The item numbers (1, 2, 3, etc.) assigned to components relate the parts list to the illustration. Item .
198 R DETAIL D DETAIL A-C AIR CYLINDER MOUNTING HARDWARE P. O. Box 400, Kenner, LA 70063-0400 Pellerin Milnor Corporation Air Cylinder Assemblies DETAIL F-L DETAIL E DETAIL P-S DETAIL M-N EXPLOSION HAZARD - Air cylinder can burst apart with great force. Circled items are under high spring tension. Follow maintenance instructions MSSM0130AE carefully. Litho in U.S.A.
199 Parts List—Air Cylinder Assemblies P. O. Box 400, Kenner, LA 70063-0400 Pellerin Milnor Corporation A52 00200 SA 10 019Q AAC14001A A76AC001A A76AC001B A75 01200 A75 01300 SA 10 019 AAC14001 A25 00600 AAC64001 AAC65001 AAC58001 F G H I J K L M N P Q R S 95000Z AIRCYL=BRAKE ASSY 7258J2N 93481B AIRCYL=BRAKE ASSY 6446E6N 89483T*BRAKE CYL ASSY=4226QWE+DYA 90000Z AIRCYL-LONG= 42S6PSG 89463T AIR CYL.2-3/8 BORE 2"STROKE 89463@ AIR CYL.2-3/8 BORE 3"STROKE 89463T*AIR CYL.
BMP830078/2005525B (Sheet 3 of 3) R Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Item Used In Parts List, cont.
