Instructions / Assembly

4
5
Item Description Quantity
Side handle 1
5" Swivel caster
with brake
2
5" Rigid caster 2
Shelf hinge bracket 2
Front bumper 8
Rear bumper 2
Corner extrusion 2
Cord storage bracket 2
Bottle opener 1
NOTE: Begin product assembly close to the nal
intended location of your station. This product is
heavy and may be difcult to move after assembly.
Attaching the Side Handle
Attach the side handle to the station using four bolts
(AA). The side handle can be attached to either side
of the station.
NOTE: The holes in the station are tapped and do
not require nuts.
Installing the Casters
CAUTION
Two people may be required to
complete installation.
CAUTION
Do not overtighten the screws.
1. Ensure all station drawers are securely locked into
place using the key lock on the station.
2. Lay the station on its back. Use the packaging
material to protect the nish.
3. Mount the two swivel casters with brake to the
station using four bolts (CC) and washers (BB)
per caster. The swivel casters with brake should
be installed on the end of the station with the side
handle.
4. Mount the two rigid casters to the opposite end
of the station using four bolts (CC) and washers
(BB) per caster.
5. Tighten all bolts securely with a wrench.
6. Return the station to its upright position.
Installing the Corner Extrusions
and Bumpers
Place the front bumpers on both ends of the extrusion
by sliding the extrusion into the cavity of the bumpers.
Attach the front bumpers with extrusions using two
screws (EE) per bumper.
Attach the two rear bumpers to the back of the lower
cabinet using two screws (EE) per bumper.
EE
ASSEMBLY
CAUTION
Be sure to follow the assembly in-
structions for the appropriate sta-
tion. Do not use power tools to assemble station.
Tighten bolts with hand wrenches.
Tools Required
Phillips
screwdriver
Safety
goggles
10 mm
Wrench
13 mm
Wrench
Hardware Included
NOTE: Items not shown to actual size. Hardware
lengths are approximate.
Hardware Item Description Quantity
AA Bolt M6 x 16L 8
BB
Steel washer
19 x 8.5 x 2
16
CC Bolt M8 x 18L 16
DD Screw M4 x 12L 8
EE Screw M4 x 16L 12
FF Nut M6 2
GG
Shoulder bolt
M6 x 8L
2
HH
Nylon washer
19 x 8.5 x 1.5
2
II
M6*16
(3)
2PCS
Screw M6 x 16L 2
Installing the Cord Storage Brackets
Attach the brackets to the station with two screws
(DD) per bracket. Orient the brackets with one
pointed up and one pointed down so that the power
outlet cord can be wrapped around the brackets for
storage.
Installing the Storage Shelf
Attach the shelf hinge brackets to either side of the
cabinet using two bolts (AA) for each bracket. Attach
the storage shelf to the brackets using one washer
(HH), nut (FF) and bolt (GG) on each end.
FF
AA
GG
HH
Installing the Bottle Opener
Attach the bottle opener to the left side of the cabinet
using two screws (II).
USB Power Outlet
The USB ports on the power outlet can be used to
charge any device that uses less than 2.1A of DC
electrical current.
NOTE: Any device that uses more than 2.1 A of DC
electrical current will trip a self-resetting overload and
disable the output.
OPERATION
WARNING
To avoid injury or property damage,
do not exceed maximum drawer
capacity. Use care when moving the station on
incline or rough surface. Station may tip if weight
is not evenly distributed front to back and side
to side. Place more than half the total load weight
on the bottom drawers when possible.
Locking and Unlocking the Station
NOTE: The drawers must be fully closed before
locking/unlocking the unit.
Insert the key. Turn it fully left to lock, or fully right
to unlock. Always remove the key after locking and
unlocking.
Using the Caster Brakes
To lock the swivel casters,
step down on the levers
marked ON. Be sure to lock
all casters to prevent station
from rolling or swiveling. To
unlock casters, push down
on the levers marked OFF.