This product is protected by the United States Federal and/or State Law including Patent. Trademark. and for Copyright Laws ©2017 Minks Lighting Inc Manual design and all elements of manual design are protected by United States Federal and for State Law including Patent. Trademark and for Copyright Laws.
The Minka-Aire® warranty is for from the date of purchase from an authorized Minka-Aire® Lifetime dealer This warranty is only valid to the original purchaser or user against all defect sin material and workmanship tight bulbs excluded] for one {1} full year. Additionally, Minka-Aire® warrants the motor only for the lifetime of the Minks Aire® ceiling fan {excluding wall controls and electrical components), to the original purchaser or user.
Warranty Service Information To obtain warranty service during the warranty pried, the purchaser should return the fan with the sales receipt to the original place of purchase. The authorized Minka-Aire® dealer, at its sole discretion, will either repair or replace the fan after verifying the legitimacy of the warranty claim. Replacement is subject to availability of the same model.
SAFETY RULES— — 1 PACKAGE CONTENTS INSTALLING THE FAN HANGING THE FAN ELECTRICAL CONNECTIONS 5 FINISHING THE INSTALLATION Y /% ?Lateran @_ 5 1151 W. Bradford Court.
1 SAFETY RULES 1.Before you begin installing the fan, shut power off the circuit breaker of the fuse box 2 Be cautious] Read all instructions and safety information before installing your new fan. Review accompanying assembly diagrams 3. Make sure that all electrical connections comply with local codes, ordinance, or National Electrical Codes. Hire a qualified electrician or consult a do-it your self wiring handbook iF you are unfamiliar with installing electrical wiring 4.
ATTENTION:The Energy Policy Act of 2005 requires this Fan to be equipped with a 190 watt limiting device If laming exceeds 190 watts. the ceiling fan's light kit will shut off automatically. NOTE: The important safeguards and instructions appearing in this manual are not meant to cover all possible conditions and situations that may occur.
2 PACKAGE CONTENTS Unpack your fan and check the contents. You should have the fol lowing items: 1. Hanger bracket {Hanger bracket A. Mounting hardware: support included 10%1x 1.5" Woody screws{2 pes) 2 Canopy 3245019 Tm Washer (2 pes) 3. Canopy cover 8432 374°Electrical box screws {2 pest 4 Standard down rod assembly (61 Spring washers (2 pes} 5. Coupling cover 8% Star washers {2 pes) 6. Fan mutilator housing /LED assembly Wire nuts (3 pes 7 Hook B. V425 Motor screws §9 8 Glass .
Tao's Required: Philips screw driver. slotted screw driver. step-ladder, wire cutters, electrical tape MOUNTING OPTIONS If there isn't an existing mounting box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers Secure the outlet box directly to the building structure. Use appropriate Fasteners and building materials.
4 HANGING THE FAN WARNING: All of the parts, hardware and components such as the hanger bracket and hanger bail have been provided for ¥our safety and the proper Installation of your new selling fan. The use of other parts, hardware or components not supplied by Minks Aire® with the fan will cold the Minks Alrs® Warranty. REMEMBER to tum off the power. Follow the steps blow te hang your fan properly: Step 1.Secure the Hanger Bracket to the ceiling outlet box using the screws.
5 ELECTRICAL CONNECTIONS WARNING: To avoid possible electrical shock be sure electricity is turned off at the main fuse or breaker box before wiring NOTE: The Ire Contre!® System for this DC metro fans is equipped with a learning frequency function which has 32 code combinations to prevent potential interference from other remote units. The frequency on your Receiver and Transmitter units have been preset at the factory. {Fig. 11) No frequency change is necessary.
Step 1. Motor to House Supply Wires Electrical Connections: Connect the WHITE wire {Neutral) from the outlet box te the WHITE wire marked "AC in N’ from the motor. Connect the BLACK wire (Hot} from the outlet box to the BLACK wire marked "AC in L' from the motor. Secure all wire connections with the plastic wire nuts provided. {Fig. 12) QUEEN OR BARE ‘COPPER (GROUSE) Step 2. if your outlet box has @ GROUND Walgreen or Bare Copper connect this wire to the Hanger Ball and Hanger Bracket Ground wires.
6 FINISHING THE INSTALLATION Step 1. Remove 1 of the 2 screws from the bottom of the hanger bracket and loosen the other one half 8 turn from the screw head Sta 2. Slide the canopy up towards the hunger bracket and place the key hole on the canopy over the screw on the hanger bracket turn canopy until it locks in place at the narrow section of the key holes. (Fig. 13} Step 3.
ATTACHING THE FAN BLADE THE FOLLOWING OPERATIONS MUST BE ACCOMPLISHED BEFORE INSTALLING THE LIGHT KIT insets one fan blade inch the blade slot on the motor housing and secure with the screws and washers Securely tighten screws. Repeat process with other blades (Fig. 14) Notice THIS SIDE UP*labe! on fan blades.
8 INSTALLING THE LIGHT PLATE AND THE GLASS SHADE Place onc screw to the motor assembly and keep this screw loosen. Align the key hole from light kit housing ts the loosen screw on the motor assembly to hang the tight kit housing under motor assembly. Place 5 screws and tighten all screws to ensure light kit housing is firmly attached to motor assembly {Fig. ATTENTION: The Energy Policy Act of 2005 requires this fan to be equipped with 7S watt limiting device.
OPERATING THE REMOTE CONTROL/WALL CONTROL Re mate Control only: install a A23 12 volt battery chaffinch. To prevent damage to transmitter remove the battery if not used for long periods of time. Your DC brutishness motor is equipped with a self 8. £ Reverse button: o leaning Frequency function remote control.
Note: The aura learning function will oty mandate within 60 seconds when turning the fan's AC power ON 1. Select desired frequency from the back of transmitter. 2 Press the transmitter's "OFf’ button, and hold the "Off" button for over 10 seconds. Once the receiver has detected the frequency.
Speed settings for warm or cold weather depend on factors such as room size, ceiling height and number of Fans NOTE: ko change the direction of the rotation of the blades the fan must be in operation mode Warm Weather {forward) A DOWNWARD airflow creates cooling effect as shown in Figure 17. This allows you te set your ais conditioner warmer setting without affecting your comfort.
10 CALCAREOUS Here are some suggestions to help maintain your fan 1. Because of the fan's natural movement some connections may become lose. Check the support connections, brackets and blade attachments twice a year. Make sure they are secure. (it snot necessary to remove fan from the ceiling} 2 Clean your fan periodically to help maintain its new appearance over the year.
SYMPTOM Fan will not start SOLUTION ¢ Check to make sure the wall switches turned on. e Check circuit fuses or breakers ® Caution Make sure the power is turned off before performing the following steps * Remove canopy sod check wire connections # Check wall control transmitter connection applicable + Note:fan must be installed at a maximum distance of 40 feet from the transmitting unit for proper signal transmission between the transmitting unit and the fan's receiving unit.
SYMPTOM Fan Wobble SOLUTION » Mote: All blade sets are grouped by weight. Because wood and plastic blades vary in density. the fan may wobble even though blades are matched # Make sure outlet box is secured to building structure, if necessary use the wood screws provide to further outlet box to joist # Make sure hanger bracket is secure to the outlet box, screws are tight.
SYMPTOM Frequency interference SOLUTION 1. Turn the power off to your ceiling fan 2. Please use a small size tool to change the frequency settings on the control system 3. Return power to the unit.
12 SPECIFICATIONS These are typical readings. Your actual fan may vary They do not include amps and wattage used by the lightly For any additional information about your Minks Aire® Ceiling fan, please write to: 2 o Fan Size Speed Volts Amps Watts BPM NW. GW CF Low 120 0052 3861 52 802 1000 56° ) 2993 Extra High 120 064931 4186 184 kgs kss e.