SPECTRE BY U.S.
This product is protected by United States Federal and/or State Law, including Patent, Trademark and/or Copyright laws. Manual design and all elements of manual design are protected by U.S. Federal and/or State Law, including Patent, Trademark and/or Copyright laws.
The Minka-Aire® warranty is for one (1) year from the date of purchase from an authorized Minka-Aire® dealer. This warranty is only valid to the original purchaser or user against all defects in material and workmanship (light bulbs excluded) for one (1) full year. Additionally, Minka-Aire® warrants the motor only for the lifetime of the Minka Aire ceiling fan (excluding wall controls and electrical components), to the original purchaser or user.
Warranty Service Information To obtain warranty service during the warranty period, the purchaser should return the fan with the sales receipt to the original place of purchase. The authorized Minka-Aire® dealer, at its sole discretion, will either repair or replace the fan after verifying the legitimacy of the warranty claim. Replacement is subject to availability of the same model. If the model is unavailable it will be replaced by one of equal value.
SAFETY RULES........................................................................................... 1 ATTACHING THE FAN BLADES................................................................. 7 PACKAGE CONTENTS............................................................................2 INSTALLING THE LED LIGHT KIT.............................................................. 8 INSTALLING THE FAN............................................................................
1 SAFETY RULES 1. Before you begin installing the fan, shut power off at the circuit breaker of the fuse box. 2. Be cautious! Read all instructions and safety information before installing your new fan. Review accompanying assembly diagrams. 3. Make sure that all electrical connections comply with local codes, ordinances, or National Electrical Codes. Hire a qualified electrician or consult a do-it-yourself wiring handbook if you are unfamiliar with installing electrical wiring. 4.
NOTE: The important safeguards and instructions appearing in this manual are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution and care are factors which can not be built into this product. These factors must be supplied by the person (s) installing, caring for and operating the unit. NOTE: READ AND SAVE ALL INSTRUCTIONS! WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR OTHER PERSONAL INJURY, MOUNT FAN ONLY TO A U.L.
2 PACKAGE CONTENTS 2 Unpack your fan and check the contents. You should have the following items: 1. Fan blades (4) 2. Hanger bracket 3. Canopy 4. Canopy cover 5a. Standard downrod assembly 5b. Minimum-length downrod (for close to ceiling mounting only) 6. Fan motor/housing assembly 7. 17W LED Light kit 8. Remote control with holder and 2 mounting screws 9. 12V MN21/A23 battery 10. Balancing kit A. Mounting hardware: #10 x 1.5" Wood screws (2 PCs.) #8 x 3/4" Machine screws (2 PCs.) Lock washers (2 PCs.
Tools Required: Phillips screw driver; slotted screw driver; step-ladder; wire cutters; electrical tape. MOUNTING OPTIONS If there isn't an existing mounting box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Secure the outlet box directly to the building structure. Use appropriate fasteners and building materials. The outlet box and its support must be able to fully support the moving weight of the fan (at least 50 lbs.).
4 HANGING THE FAN WARNING: All of the parts, hardware and components such as the hanger bracket and hanger ball have been provided for your safety and the proper installation of your new ceiling fan. The use of other parts, hardware or components not supplied by Minka Aire® with the fan will void the Minka Aire® Warranty. REMEMBER to turn off the power. Follow the steps below to hang your fan properly: Step 1.
DOWNROD OUTLET BOX ALLEN SET SCREWS HITCH PIN LOCK PIN HANGER BALL CROSS PIN DOWNROD SET SCREW SUPPLY WIRES CANOPY CANOPY COVER HITCH PIN ALLEN SET SCREWS ALLEN WRENCH DOWNROD REGISTRATION SLOT HANGER BRACKET Fig. 5 Fig. 6 Fig. 7 LOCK PIN Fig. 8 Fig. 9 Fig.
5 ELECTRICAL CONNECTIONS WARNING: To avoid possible electrical shock be sure electricity is turned off at the main fuse or breaker box before wiring. NOTE: The Aire Control® System for this DC motor fans is equipped with a learning frequency function which has 32 code combinations to prevent potential interference from other remote units. The frequency on your Receiver and Transmitter units have been preset at the factory. (Fig.
Step 1. Motor to House Supply Wires Electrical Connections: Connect the WHITE wire (Neutral) from the outlet box to the WHITE wire marked "AC in N" from the motor. Connect the BLACK wire (Hot) from the outlet box to the BLACK wire marked "AC in L" from the motor. Secure all wire connections with the plastic wire nuts provided. (Fig. 12) Step 2. If your outlet box has a GROUND wire (Green or Bare Copper) connect this wire to the Hanger Ball and Hanger Bracket Ground wires.
6 FINISHING THE INSTALLATION OUTLET BOX Step 1. Remove 1 of the 2 screws from the bottom of the hanger bracket and loosen the other one half a turn from the screw head. Step 2. Slide the canopy up towards the hanger bracket and place the key hole on the canopy over the screw on the hanger bracket, turn canopy until it locks in place at the narrow section of the key holes. (Fig. 13) HANGER BRACKET HANGER BALL CANOPY Step 3.
7 ATTACHING THE FAN BLADES Attach the fan blade to the blade holder using the screws and fiber washers provided. Tighten screws securely. Repeat process for remaining blades. (Fig. 14) SCREWS AND FIBER WASHERS BLADE HOLDER Fig.
8 INSTALLING THE LED LIGHT KIT Step 1. Remove the 3 screws from the mounting plate. Step 2. While holding the LED light kit under the fan motor assembly, make the 2-pin wire connections: - Red to white - Black to black Step 3. Carefully tuck all wire connections back into the LED light kit, then install the LED light kit onto the mounting plate with 3 screws previously removed. Be sure to tighten all screws. (Fig. 15) MOUNTING PLATE CONNECTORS LED LIGHT KIT Fig.
OPERATING THE REMOTE CONTROL/WALL CONTROL Remote Control only: Install a A23 12 volt battery (included). To prevent damage to transmitter remove the battery if not used for long periods of time. Reverse button: Restore power to ceiling fan and test the B. This button is used to change the direction of transmitter as below for proper operation: the rotation of the blades; forward for warm A. 1, 2, 3, 4, 5 and 6 button: weather or reverse for warm weather.
1. Select desired frequency from the back of Speed settings for warm or cold weather depend on factors such as room size, ceiling transmitter. height and number of fans. 2. Press the transmitter’s “ ” button, and hold the “ ” button for over 5 seconds or until the NOTE: To change the direction of the rotation of the blades the fan must be in operation mode. fan’s light blinks. 3. “D” and “ON” dip switch: The “D” selection is the light dimmable selection and is to be used with all bulbs except for CFL bulbs.
SUMMER OPERATION WINTER OPERATION (CLOCKWISE DIRECTION) (COUNTERCLOCKWISE DIRECTION) Fig 16 Fig 17
10 CARE OF YOUR FAN Here are some suggestions to help maintain your fan. 1. Because of the fan's natural movement some connections may become loose. Check the support connections, brackets and blade attachments twice a year. Make sure they are secure. (It is not necessary to remove fan from the ceiling). 2. Clean your fan periodically to help maintain its new appearance over the year. CAUTION; many common household cleaning products contain chemicals that could damage the finish of your fan.
TROUBLESHOOTING SYMPTOM Fan will not start SOLUTION Check to make sure the wall switch is turned on. Check circuit fuses or breakers. Caution! Make sure the power is turned off before performing the following steps. Remove canopy and check wire connections. Check wall control transmitter connections (if applicable). Note: Fan must be installed at a maximum distance of 40 feet from the transmitting unit for proper signal transmission between the transmitting unit and the fan's receiving unit.
SYMPTOM Fan Wobble SOLUTION NOTE: All blade sets are grouped by weight. Because wood and plastic blades vary in density, the fan may wobble even though blades are matched. Make sure outlet box is secured to building structure, if necessary use the wood screws provided to further secure outlet box to joist. Make sure hanger bracket is secure to the outlet box, screws are tight. If a Balancing kit is provided follow the instructions included with the balancing kit to help correct any excessive wobble.
SYMPTOM Frequency Interference SOLUTION 1. Turn the power off to your ceiling fan. 2. Please use a small size tool to change the frequency settings on the control system. 3. Return power to the unit. Note: After the AC power is on, do not press any other button on the transmitter before pressing the "Stop" button, doing so will cause the procedure to fail. 4. Within 60 seconds of turning the Fan's AC power ON. Press the transmitter's "Stop" button and hold the "Stop" button for 10 seconds. 5.
12 SPECIFICATIONS Fan Size These are typical readings. Your actual fan may vary. They do not include amps and wattage used by the light(s). 60" For any additional information about your Minka Aire Ceiling fan, please write to; Speed Low Medium Low Medium Medium High High Extra High Volts Amps Watts RPM 120 120 120 120 120 120 0.05 0.08 0.13 0.20 0.30 0.44 2.8 5.0 8.0 13.0 21.5 31.8 48 71 94 119 143 163 CFM N.W. G.W. 2133 3149 4018 4996 5987 7230 8.02 9.31 1.873' kgs kgs R 1151 W.