Installation Sheet

INSTALLATION INSTRUCTIONS
Item# 1356 (Rev. 06/09/2012)
READ AND SAVE THESE INSTRUCTIONS
WARNING ! SHUT PO WER OFF AT F U S E OR CI RCUIT BRE AK E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Fig. 1
Fig. 2
Fig. 3
ASSEMBLING THE FIXTURE (Fig.1)
1. Carefully remove the fixture from the carton and check that
all parts are included as shown in the illustration.
2. Shut off power at the circuit breaker and remove old fixture
including the mounting hardware.
3. Secure the upper Poly Assembly (A) to Light Cluster
Assembly (H), pull the wires from top Loop until taut.
4. Align the pre-drilled holes on the Arm (B) to the Stud (I) on
the bottom of upper Poly Assembly (A) and Point (K) on the
top of upper Poly Assembly (A) and secure them with Cap
Nut (J) and Thumb Screw (C) separately.
5. Adjust the Arms (G) on the Light Cluster Assembly (H) to the
proper position as shown in Fig.1.
6. Secure the Finial (F) to the bottom of Light Cluster Assembly
(H).
7. Place the Glass Shade (D) over the Socket Cup (E) by
twisting it clockwise as shown in Fig.1
HANGING THE FIXTURE (Fig. 2)
8. Thread Nipple into Loop until snug.
9. Thread other end of Nipple with Loop attached into crossbar
until snug.
10. Place Lock Washer over end of Nipple protruding through
crossbar and thread Hex Nut onto nipple until tight.
11. Take the crossbar assembly and mount to ceiling junction
box with junction box screws. Tighten screws securely with
screwdriver.
12. By measuring determine correct number of links needed for
proper hanging height.
13. Use a pair of chain pliers to open one end link of the chain,
attach the chain to the fixture’s loop, and close the link. Slip
Loop Collar and Canopy over the chain.
14. Open the other end link of the chain and lift the fixture to
attach to the ceiling loop, close the chain link.
14. Lace the fixture’s wires through the chain links and pull until
taut. Feed the fixture wires through the Loop and Nipple and
pull until taut.
CONNECTING THE WIRES (Fig. 3)
15. At this point, connect the electrical wire as shown in
(Fig. 3), making sure that all wire connectors are secured. If
your outlet has a ground wire (green or bare copper), connect
the fixture’s Ground Wire to it. Otherwise, connect the
fixture’s Ground Wire directly to the crossbar using the Green
Screw provided.
16. Tuck the wire connections neatly into the ceiling junction box
and then raise the canopy all the way to the ceiling. Raise
the Lock Collar and thread onto ceiling Loop protruding
through Canopy.
17. Install the light bulbs (not included) in accordance with the
fixture’s specifications. (DO NOT EXCEED THE MAXIMUM
WATTAGE RATING!) (NE PAS DEPASSER LA PUISSANCE
NOMINALE MAXIMALE!)
Your installation is now complete. Return power to the
junction box and test the fixture.
Note: Illustration (Fig. 1) on this manual is for installation
purposes only. It may or may not be identical to the fixture
purchased.
LA-1506E
Notice: It is important to use proper chain pliers (not
included)
To OPEN and CLOSE the chain included with this
fixture. Do not open them with other tools that may
twist or stress the chain links. It is important to use
proper chain pliers like the ones shown in the diagram.
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
White
(Neutral)
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
Green
(Ground)
Nipple
Screw
Canopy
Loop
Chain
Hex Nut
Lock Washer
Crossbar
Loop
Lock Collar
Junction Box
(Ceiling)
“U.S. Patents; D577,459;D579,143
This product is protected by United States Federal and/or
State Law, including Patent and/or Copyright laws.”
© Minka Lighting, Inc.
F
J
C
B
A
E
D
K
I
H
G