Installation Sheet

INSTALLATION INSTRUCTIONS
Item#1358 (Rev. 06/09/2012)
READ AND SAVE THESE INSTRUCTIONS
WARNING ! SHUT PO WER OFF AT F U S E O R CI R C U IT B RE AK E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Fig. 1
Fig. 2
Fig. 3
ASSEMBLING THE FIXTURE (Fig.1)
1. Carefully remove the fixture from the carton and check that all parts
are included as shown in the illustration.
2. Shut off power at the circuit breaker and remove old fixture including
the mounting hardware.
3. Secure the upper Poly Assembly (A) to Light Cluster Assembly (H),
pull the wires from top Loop until taut.
4. Align the pre-drilled holes on the Arm (B) to the Stud (I) on the
bottom of upper Poly Assembly (A) and Point (K) on the top of upper
Poly Assembly (A) and secure them with Cap Nut (J) and Thumb
Screw (C) separately.
5. Adjust the Arms (G1 and G2) on the Light Cluster Assembly (H) to
the proper position as shown in Fig.1.
6. Screw the Finial (F) to the bottom of Light Cluster Assembly (H).
7. Screw the Glass Shade (D) over the Socket Cup (E) by twisting it
clockwise as shown in Fig.1
8. Install the light bulbs (not included) in accordance with the fixture’s
specifications. (DO NOT EXCEED THE MAXIMUM WATTAGE
RATING!) (NE PAS DEPASSER LA PUISSANCE NOMINALE
MAXIMALE!)
HANGING THE FIXTURE (Fig. 2)
IMPORTANT: For a safe and secure installation, these fixtures must be
installed by means of support that is independent of the outlet box.
SUGGESTED INSTALLATION:
9. Provide a 1/4 IPS pipe with one end securely mounted to a beam or
a structural member. The other end should protrude through the
center of the outlet box as shown.
10. Assemble the ceiling loop, nipple, nuts and hickey to center 1/4
IPS support pipe and adjust overall length to allow the ceiling loop to
hold the canopy flush to the ceiling. When the adjustments have
been completed, secure the three nuts, as shown.
11. Attach the chain to the fixture loop. Slip the lock collar and canopy
over the upper end of the chain. Open the end link of chain and lift
the fixture to attach to the ceiling loop and secure the link.
12. Lace the fixture wires, ground and safety cable through the chain
and loop, exiting through the side of hickey. Run cable through the
top of the outlet box and secure to structural member, locking with
the set screw assembly.
CONNECTING THE WIRE (Fig. 3)
13. At this point, connect the electrical wire as shown in figure 3,
making sure that all wire connectors are secured. If your outlet has
a ground wire (green or bare copper), connect the fixtures Ground
Wire to it. If not, consult your electrician for proper grounding.
14. Tuck these wire connections neatly into the ceiling junction box
and then raise the canopy all the way to the ceiling. Raise the Lock
Collar and thread onto ceiling Loop protruding through canopy.
Your installation is now complete. Return power to the junction box
and test the fixture.
Note: Illustration (Fig. 1) on this manual is for installation
purposes only. It may or may not be identical to the fixture
purchased.
LA-1499E
Notice: It is important to use proper chain pliers (not included)
To OPEN and CLOSE the chain included with this fixture. Do not
open them with other tools that may twist or stress the chain
links. It is important to use proper chain pliers like the ones shown
in the diagram.
Lock Collar
Canopy
Chain(End link)
Set Screw Assembly
Fixture wires
Fixture
Safety cable
To structural member
Ground wire
Ceiling loop
Hex Nut
Nipple
Hickey
1/4IPS(1/2 dia.)pipe
(Not provided)
K
H
G1
G2
J
I
A
B
C
D
E
F
G2
G1
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
White
(Neutral)
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
Green
(Ground)
“U.S. Patents; D577,459; D579,143
This product is protected by United States Federal and/or
State Law, including Patent and/or Copyright laws.”
© Minka Lighting, Inc.