TM TM C320/C330 Series
Table of Contents en Getting to know your dash cam..................................................................................................... 2 Power button...............................................................................................................................3 Function keys...............................................................................................................................3 System icons.............................................................
Getting to know your dash cam Note: The screenshots and other presentations shown in this manual may differ from the ones generated by the actual product.
Power button en Press and hold for 2 seconds to manually turn the recorder on and off. Note: If the system does not turn off by keeping the Power button pressed, you can force it to shut down by inserting a small rod (such as a straightened paperclip) into the Shutdown button. Function keys The device provides 4 function keys to control the corresponding icons displayed on the LCD screen. The keys' functions may vary on different screens.
System icons en Various system icons on the title bar at the top of the screen provide the status information of your device. The icons displayed will vary depending on your device model and state. 1 2 3 4 1 Recording indicator 2 Time display 5 3 Recording with sound is disabled 4 GPS signal* 5 Your current speed* * For selected models only. System indicator The System indicator glows in green when the recorder is charging.
Using your recorder in a vehicle Make sure that your car is parked on level ground. 1. Follow the instructions below to securely mount your recorder in a vehicle. 2. Connect the car charger to the cigarette lighter. Route the cables through the top ceiling and the A-pillar so that it does not interfere with driving. Make sure that the cable installation does not interfere with the vehicles airbags or other safety features.
3. When adjusting the angle of mounting, make sure that the camera’s view is parallel with the level ground and the ground/sky ratio is close to 6/4. Note: To ensure the highest quality recordings, you are advised to place the recorder near the rear-view mirror. Select an appropriate location for mounting the device in a vehicle. Never place the device where the driver’s field of vision is blocked.
Inserting a memory card en You must insert a memory card (not supplied) before you can start recording. The recorder supports Class 10 memory cards with 8 GB - 128 GB capacity. Hold the card (MicroSD) by the edges and gently insert it into the slot as shown in the illustration. To remove a card, gently push the top edge of the card inwards to release it and pull it out of the slot. Note: DO NOT apply pressure to the centre of the memory card.
Operating basics en Turning the recorder on Complete the installation according to the instructions in the “Using your recorder in a vehicle” section. Once the vehicle engine is started, the recorder automatically turns on. Setting the date and time To make sure that the date and time of your recordings are correct, check the settings before you begin recording. 1. Press to access the Settings Menu. 2. Select System > Date / Time and press . 3.
Recording in driving mode en Continuous recording By default, the system will automatically begin with continuous recording within seconds after start up. The recording may be divided into several video clips; recording will not stop between video clips. When continuous recording is in progress, you can manually stop recording by pressing . to return to the recording screen; the system will start continuous recording Press automatically.
The Parking mode function is disabled by default. You can enable the function by selecting > Parking Mode > Detection > On. Before enabling Parking mode, please check the memory storage allocation of your device. Select > System > Storage Allocation to set a proper allocation for parking recording. Changing the allocation will erase the memory card, so save any videos or photos to your computer first.
3. Press / playback. to select the desired file from the list, and then press to start 4. During playback, you can: While playing videos, press While viewing photos, press / to play the previous/next video. / to display the previous/next photo. Press to return to the list. Press to display the pop-up menu to select: - Play/Pause: Starts or pauses the playback. - Move to Event: Moves the file to the “Event” category. - Delete: Deletes the file.
Safety camera alerts en Caution: For legal reasons the safety camera function is not available in all countries. You can receive alerts to warn you about the locations of safety (speed) cameras*, which will enable you to monitor your speed through these areas. 110 108 km/h 500m * For selected models only. When a safety camera appears and is positioned in the detectable direction, you will receive alerts.
Adding a safety camera en Note: You can add a custom safety camera only when a GPS fix is established. Your recorder allows you to customise the safety camera database. You can add up to 100 custom safety cameras in your recorder. Follow the steps to configure a custom safety camera: 1. To add a custom safety camera in the current location, press on the recording screen. 2. The next time when you pass by the location, you will receive alerts by the recorder. 3.
System settings To customise the system settings, press en . Note: Depending on your MiVue model, certain setting options may not be available. File Playback Plays the recorded videos and photos. Sound Recording Sets if you want to include sounds in the recordings. The default setting is On. SafetyCam Sets how you want to be notified of safety cameras. The available settings include: - Alert Sound: The options are Beep, Voice and Mute. - Alert Distance: The options are Short, Medium and Long.
Parking mode automatically. - Motion Detection: Sets the sensitivity level of motion detection to Low, Medium or High. - G-Sensor Sensitivity: Sets the sensitivity level of the G sensor that allows automatic triggering of the parking recording when the dash cam is in Parking mode. Video Recording Changes the settings of recording, including: - Video Clip Length: Sets the length of each video clip for a continuous recording (1 min, 3 min or 5 min).
- Welcome Sound: Enables or disables the notification sounds during start-up. - Volume: Adjusts the volume level. - LCD Standby: Selects Always On to keep the LCD on; or sets the timer for the LCD to turn off automatically (10 sec, 1 min or 3 min) after recording starts. Selecting HUD will turn off the LCD (in specified time) but still display the time and speed information. - Language: Sets the language. - Distance Unit: Sets the preferred distance unit.
MiVue Manager en MiVue Manager™ is a tool for you to view the videos recorded on a recorder. Note: Not all features are available for every model. Installing MiVue Manager Download MiVue Manager from the Support page of Mio website (www.mio.com/support) and follow the on-screen prompts to install it. Make sure to download the correct software version (Windows or Mac) according to your computer's operating system. Playing the recording files 1.
1 Skips to the previous / next file on the list. en 2 Starts or pauses the playback. 3 Changes the playback speed to 1/4x, 1/2x, 1x (default), 1.5x, or 2x. 4 Mutes or unmutes the volume. 5 Adjusts the volume level. 6 Plays the video in full screen. 7 Displays the playback progress. You can click on a point along the track bar to move directly to a different location for the playback. 5.
5 Opens the Settings Menu. The Settings items are described as follows: - Change Language: Sets the display language of MiVue Manager. - Change Skin: Sets the colour scheme of MiVue Manager. - Check for Update: Checks if there is any new version of MiVue Manager. Internet access is required for this feature. - About: Displays the version and copyright information of MiVue Manager. 6 Exports the GPS information of the selected file in the KML format to the specified location on your computer.
For more information Caring for your device Taking good care of your device will ensure trouble-free operation and reduce the risk of damage. Keep your device away from excessive moisture and extreme temperatures. Avoid exposing your device to direct sunlight or strong ultraviolet light for extended periods of time. Do not place anything on top of your device or drop objects on your device. Do not drop your device or subject it to severe shock.
Precautions and notices en Do not operate the device while driving. Using this product does not change the requirement for a driver to take full responsibility for his or her behavior. This responsibility includes observing all traffic rules and regulations in order to avoid accidents, personal injury or property damage. A window mount is needed when using the recorder in a car.
Do not attempt to service the unit. There are no serviceable parts inside. Replace the unit if it is damaged or exposed to excess moisture. About the battery CAUTION! This unit contains a non-replaceable internal Lithium Ion battery. The battery can burst or explode, releasing hazardous chemicals. To reduce the risk of fire or burns, do not disassemble, crush, puncture or dispose of in fire or water. Use a specified battery in the equipment.
Regulatory information en For regulatory identification purposes, MiVue C320/C330 Series is assigned a model number of N530. Products with the CE marking comply with the Radio Equipment Directive (RED) (2014/53/EU) - issued by the Commission of the European Community.
Declaration of conformity Hereby, MiTAC declares that this N530 is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. WEEE This product must not be disposed of as normal household waste, in accordance with the EU directive for waste electrical and electronic equipment (WEEE – 2012/19/EU). Instead, it should be disposed of by returning it to the point of sale, or to a municipal recycling collection point.
Revision: R01 (9/2017) Disclaimer The screenshots in this manual may differ between different operating systems and software versions. You can download the latest User Manual of your product from Mio™ website (www.mio.com). Specifications and documents are subject to change without notice. MiTAC does not warrant this document is error-free. MiTAC assumes no liability for damage incurred directly or indirectly from errors, omissions or discrepancies between the device and the documents.
