Troubleshooting guide
Table Of Contents
- Chapter 1 Getting Started
- Chapter 2 Initial Setup
- Connect PC to Controller
- Establish Communication with Controller
- Enable Licenses and Options
- MCD Software Installer Tool Requirements for AMC
- 3300 ICP System Requirements for AMC
- Automatic Sync with AMC via MCD Software Installer Tool (Rel 6.0 or later)
- Automatic Sync via System Administration Tool
- Manual License and Options Entry via MCD Software Installer Tool
- Manual License and Options Entry via System Administration Tool
- Install the Online Help (Optional)
- Verify the Operation of the Controller
- Chapter 3 Installation and Programming
- Install Hardware
- Determine Controller Module Configuration
- Identify Controller Component Options
- Remove Controller Cover
- Install Controller Modules
- Install Controller Stratum 3 Clock Module
- Install Controller Hardware
- Rack Mount the Controller
- Wall Mount the CX/CXi and CX II/CXi II Controller
- Install Service Units and Cabinets
- Installing SX-200 Bays
- Install Telephones
- Install and Configure Music on Hold
- Program 5485 IP Paging Unit
- Register IP Devices from the Telephone
- Program System
- Install Hardware
- Chapter 4 Software Installation
- About Installing and Upgrading Software
- Install System Software Manually
- The MCD Software Installer Tool
- Upgrade System Software
- System Software Installation Details
- Installing MSL Software on APC (CX/CXi) or APC-CX(i) II (CX II/CXi II)
- Installing MSL Software on an MXe Server
- Installing System Software on the FTP Server
- Upgrade to MCD 5.0 and Group Licensing
- Upgrade the 3300 ICP Software on the MXe Server
- Upgrading/Installing with Maximum Elements Change
- Upgrade to Rel 6.0 or later with Flexed Dimensions
- Apply a Software Patch
- Distributing New Firmware to IP Phones
- Load IP Phone Software Remotely
- Downgrading to a Previous Software Release
- Chapter 5 Maintenance
- Check System
- View Logs
- Detect Device Moves for E911
- Analyze IP Phone Issues
- Power Down the Controller
- Perform a System Reset
- Back Up a Database
- Restore a Database
- Migrate SX-2000 Database Across Platforms
- Converting a PRI Database on a Universal NSU
- Export Configuration Data
- Import Configuration Data
- Restoring Default Addresses on MXe Server
- Assign Static IP Addresses to IP Phones
- Providing Power Over Ethernet to Devices (CXi/CXi II)
- Recover MXe Server
- Chapter 6 Install and Replace Units
- Component Replacement Notes
- Add or Replace Controller FRUs
- Controller Modules
- Stratum 3 Clock Module
- System i-Button/System ID Module
- Analog Main Board
- Analog Option Board
- Application Processor Card
- E2T or RTC Processor
- Hard Drives
- Fan Complex
- Power Supply Unit
- Redundant Power Supply
- RAID Controllers
- Line Cards
- Controller Card (AX)
- Flash Cards (AX)
- Memory Module (CX, CXi, AX)
- Install Cabinet FRUs
- Appendix A Hardware Reference
- Appendix B Installation Planner
- Reserved IP Addresses
- MXe Server/MXe/AX/CXi/CXi II Requirements for IP Networking
- Controller Configuration Settings (RTC)
- DHCP Configuration Settings
- Programming E2T via Debug Cable or Secure Telnet
- Configuring External DHCP Settings for E2T
- Configuring a Windows 2000 or Windows 2003 DHCP Server (Rel 7.0 and later)
- System Administration Tool Settings
- IP Phone Settings
- Telephone Programming Guide
- Increasing DSP Resources
- Appendix C Typical Network Configurations
- Network Configuration Examples
- Cisco Discovery Protocol (CDP)
- CXi/CXi II/MXe/MXe Server Configuration
- AX Configuration Procedures
- CXi, CXi II, MXe and AX-Specific Guidelines
- Windows 2000 FTP Server
- Appendix D Status LEDs
- Controller LEDs
- Network Services Unit LEDs
- Analog Services Unit LEDs
- ASU II Card LEDs
- IP Device LEDs
- Peripheral Cabinet LEDs
- SX-200 Bay LEDs
- Digital Services Unit LEDs
- In-Line Power Unit LEDs
- Appendix E FRU Part Numbers
- Appendix F System Capacity and Parameters
- Appendix G Older Hardware and Software
- Procedures for Older Controllers
- Programming the Controller DHCP Server Settings (prior to Rel 7.0)
- To use an alternative DHCP server (prior to Rel 7.0)
- Configuring a Windows 2000 DHCP Server (prior to Release 7.0)
- Program DHCP for VLAN (prior to Rel 7.0):
- Connect a Windows 95/98 PC to the NSU via Dial-Up
- Physically Connecting the PC to an NSU
- Creating a Dial-Up Network Connection on Windows 95/98
- Migrate SX-2000 PBX Hardware
- Collecting System Logs Manually
- Collecting System Lockup Logs Manually
- Peripheral Cabinet
- Digital Service Unit (DSU)
- Index
- Procedures for Older Controllers
125
Maintenance
Last Known CDP L2 Port MAC MAC address of the CDP Layer 2 switch
where the IP device was connected on first
registration or registration after a move.
- “Unknown” device is one that does not
support CDP with its current firmware
load. A ‘Reload’ of set firmware may be
required.
- “Not Supported” device indicates that L2
switches do not support CDP. Contact the
L2 switch provider; an upgrade may be
required.
Last Known CDP Port Identifier Port number on the CDP Layer 2 switch
where the IP device was connected on first
registration or registration after a move.
Last Known CDP L2 IP Address IP address of the CDP Layer 2 switch where
the IP device was connected on first
registration or registration after a move.
State "In Service" or "Out of Service". This data
used by the system to determine whether
multiple in-service devices are connected
through the same Layer 2 MAC and Port.
Useful for identifying system configuration
issues.
Move Acknowledged “Not applicable” indicates a device that has
not moved. This is the only editable field. After
you have updated the Customer Emergency
Services ID (CESID) Assignment form,
change this field to Yes. Click Data Refresh
to remove the device from the list of Moved
devices.
Tip:Refer to the System Administration Tool online help for Device - Move
examples and explanation of field information.
Table 16: Device Connectivity Form Fields (continued)
Field name Description
Page 3 of 3