Troubleshooting guide
Table Of Contents
- Chapter 1 Getting Started
- Chapter 2 Initial Setup
- Connect PC to Controller
- Establish Communication with Controller
- Enable Licenses and Options
- MCD Software Installer Tool Requirements for AMC
- 3300 ICP System Requirements for AMC
- Automatic Sync with AMC via MCD Software Installer Tool (Rel 6.0 or later)
- Automatic Sync via System Administration Tool
- Manual License and Options Entry via MCD Software Installer Tool
- Manual License and Options Entry via System Administration Tool
- Install the Online Help (Optional)
- Verify the Operation of the Controller
- Chapter 3 Installation and Programming
- Install Hardware
- Determine Controller Module Configuration
- Identify Controller Component Options
- Remove Controller Cover
- Install Controller Modules
- Install Controller Stratum 3 Clock Module
- Install Controller Hardware
- Rack Mount the Controller
- Wall Mount the CX/CXi and CX II/CXi II Controller
- Install Service Units and Cabinets
- Installing SX-200 Bays
- Install Telephones
- Install and Configure Music on Hold
- Program 5485 IP Paging Unit
- Register IP Devices from the Telephone
- Program System
- Install Hardware
- Chapter 4 Software Installation
- About Installing and Upgrading Software
- Install System Software Manually
- The MCD Software Installer Tool
- Upgrade System Software
- System Software Installation Details
- Installing MSL Software on APC (CX/CXi) or APC-CX(i) II (CX II/CXi II)
- Installing MSL Software on an MXe Server
- Installing System Software on the FTP Server
- Upgrade to MCD 5.0 and Group Licensing
- Upgrade the 3300 ICP Software on the MXe Server
- Upgrading/Installing with Maximum Elements Change
- Upgrade to Rel 6.0 or later with Flexed Dimensions
- Apply a Software Patch
- Distributing New Firmware to IP Phones
- Load IP Phone Software Remotely
- Downgrading to a Previous Software Release
- Chapter 5 Maintenance
- Check System
- View Logs
- Detect Device Moves for E911
- Analyze IP Phone Issues
- Power Down the Controller
- Perform a System Reset
- Back Up a Database
- Restore a Database
- Migrate SX-2000 Database Across Platforms
- Converting a PRI Database on a Universal NSU
- Export Configuration Data
- Import Configuration Data
- Restoring Default Addresses on MXe Server
- Assign Static IP Addresses to IP Phones
- Providing Power Over Ethernet to Devices (CXi/CXi II)
- Recover MXe Server
- Chapter 6 Install and Replace Units
- Component Replacement Notes
- Add or Replace Controller FRUs
- Controller Modules
- Stratum 3 Clock Module
- System i-Button/System ID Module
- Analog Main Board
- Analog Option Board
- Application Processor Card
- E2T or RTC Processor
- Hard Drives
- Fan Complex
- Power Supply Unit
- Redundant Power Supply
- RAID Controllers
- Line Cards
- Controller Card (AX)
- Flash Cards (AX)
- Memory Module (CX, CXi, AX)
- Install Cabinet FRUs
- Appendix A Hardware Reference
- Appendix B Installation Planner
- Reserved IP Addresses
- MXe Server/MXe/AX/CXi/CXi II Requirements for IP Networking
- Controller Configuration Settings (RTC)
- DHCP Configuration Settings
- Programming E2T via Debug Cable or Secure Telnet
- Configuring External DHCP Settings for E2T
- Configuring a Windows 2000 or Windows 2003 DHCP Server (Rel 7.0 and later)
- System Administration Tool Settings
- IP Phone Settings
- Telephone Programming Guide
- Increasing DSP Resources
- Appendix C Typical Network Configurations
- Network Configuration Examples
- Cisco Discovery Protocol (CDP)
- CXi/CXi II/MXe/MXe Server Configuration
- AX Configuration Procedures
- CXi, CXi II, MXe and AX-Specific Guidelines
- Windows 2000 FTP Server
- Appendix D Status LEDs
- Controller LEDs
- Network Services Unit LEDs
- Analog Services Unit LEDs
- ASU II Card LEDs
- IP Device LEDs
- Peripheral Cabinet LEDs
- SX-200 Bay LEDs
- Digital Services Unit LEDs
- In-Line Power Unit LEDs
- Appendix E FRU Part Numbers
- Appendix F System Capacity and Parameters
- Appendix G Older Hardware and Software
- Procedures for Older Controllers
- Programming the Controller DHCP Server Settings (prior to Rel 7.0)
- To use an alternative DHCP server (prior to Rel 7.0)
- Configuring a Windows 2000 DHCP Server (prior to Release 7.0)
- Program DHCP for VLAN (prior to Rel 7.0):
- Connect a Windows 95/98 PC to the NSU via Dial-Up
- Physically Connecting the PC to an NSU
- Creating a Dial-Up Network Connection on Windows 95/98
- Migrate SX-2000 PBX Hardware
- Collecting System Logs Manually
- Collecting System Lockup Logs Manually
- Peripheral Cabinet
- Digital Service Unit (DSU)
- Index
- Procedures for Older Controllers
15
Initial Setup
The MXe Server is shipped with default IP addresses assigned. The
defaults are shown in Table 1.
Before You Begin
To complete this procedure, you will require
Laptop
Communications application (for example, Hyperterminal)
RS-232 serial cable
Ethernet cable (straight-through)
MCD Software Installer tool
Application Record Identification Number (AMC ARID)
Tip: If you are replacing an existing 3300 ICP controller with an MXe Server
and you want to use the same system IP address for the MXe Server, initially
you will only be able to connect to the MXe Server from the local subnet.
Before you can connect to the MXe Server from other subnets, you must
manually clear the router ARP cache or wait until the router ARP cache is
automatically updated. Refer to the latest 3300 ICP Release Notes for
instructions.
Tip: The MXe Server is shipped with two hard drives, one with the software
loaded and one blank. Before continuing, mirror the blank drive starting at
Step 11 of the procedure described in “Replace One Hard Drive in an MXe
II/MXe Server” on page 210.
Table 1: Default IP Addresses for the MXe Server
ESM Name
Default IP Address/ Subnet Mask
Virtual subnet 192.168.1.4/30
System IP Address 192.168.1.5/30
Reserved IP Address 192.168.1.6/30
Virtual broadcast 192.168.1.7/30
APC IP Address 192.168.1.8/24
Media Gateway IP Address 192.168.1.2/24
E2T Card IP Address 192.168.1.3/24
Layer 2 (L2) Switch IP Address 192.168.1.1/24