Installation manual

ManualsBrandsMitsubishi Electric ManualsDryerJT-MC106G-W-NA

EnglishFrançais

− NA - 1 −

MODEL

JT-MC106G-W-NA

Unit color -W

（White）

Hand dryer

875HJ9901

Read the manual thoroughly before beginning installation to ensure the unit is installed safely and correctly.

Installation shall comply with local requirements and Electrical Code and be performed by the dealer or a qualiﬁ ed

professional in accordance to local jurisdiction.

The "INSTRUCTION MANUAL" is for the customer. Be sure to hand it to the customer.

INDEX

Safety Precautions

Pre-installation checks

■ Checking the installation environment

■ Checking the unit, accessories

and items required for installation

Names of parts and external dimensions

Installation conditions

■ Required space for installation

■ Suitable walls

■ Making the unit easier to use

Installation method

6 – 11

Test Run

Initial setting checks

■ How to open/close the front cover

Precautions for when opening/closing

the front cover

■ Turning the heater on

■ Turning the sensor off before maintenance

INSTALLATION MANUAL

Location of Name plate indicating

Model name and Electrical ratings

Input Power: 120 Vac Single-phase

Indoor use only

For Dealers and Installers

Summary of content (16 pages)

PAGE 1
875HJ9901 Hand dryer JT-MC106G-W-NA Unit color Location of Name plate indicating Model name and Electrical ratings -W（White） Input Power: 120 Vac Single-phase Indoor use only English MODEL For Dealers and Installers INSTALLATION MANUAL Read the manual thoroughly before beginning installation to ensure the unit is installed safely and correctly.
PAGE 2
Safety Precautions The dangers arising from improper handling and the extents of the dangers are classified and explained as shown below. English Warning Prohibited The following may lead to death or serious personal injury if handled incorrectly. Do not install in locations where they may be leakages of combustible gas. This may cause fires. Do not install in locations where salt damage may occur or where corrosive, neutral or reductive gases are present. This may cause malfunctions.
PAGE 3
Pre-installation checks Warning Input Power: 120 Vac Single-phase is used. ■ Checking the installation environment Do not install the unit in the following types of locations. (This may cause malfunctions.) Outdoors Locations where the temperature could be lower than 32 F (0 C). Locations where there is a lot of dust. Locations where the temperature could be higher than 104 F (40 C). Locations where there is a lot of condensation. Locations where salt damage may occur.
PAGE 4
Names of parts and external dimensions 18 7/8 " (480) 7 1/2 " (190) English 3 15 /16" (100) 6 7/16" (163) 21/16" (52) 1 9 /16" (40) 5 7/16"(138.5) Air ﬁlter 5 15/16 " (150) 1 1 /4 " (31) 9 7/8 " (250) 9 7/8 " (251.5) 6 11 /16" (170) 8 7/16 " (215) 1 /16" Installation panel (2) 1 1 /8 " (28) ■ Main unit Power light Drain tank Unit (in. (mm)) NOTE Conﬁrm the details in the "Installation conditions" (Page 5).
PAGE 5
Installation conditions ■ Required space for installation Rear side Top side Be sure to secure at least the distances listed in the righthand table from walls, flammable (combustible) materials and so Left side on. Unit (in. (mm)) Main unit Right side ■ Suitable walls When installing on a wall, select a wall with a ﬂat and even surface. When installing on a concrete wall, use commercially available metal screw plugs. Reinforce any walls made with materials other than concrete before installation.
PAGE 6
Installation method For confirmation □ Input Power: 120 Vac Single-phase power is being used (using the incorrect power supply may cause fires, electric shocks or malfunctions). □ The ground fault circuit interrupter is attached (not attaching a ground fault circuit interrupter may result in electric shocks). □ A single wire (cable core: 2.0mm² or 3.0mm²) is being used for the power cable. Caution This hand dryer must have its own independent branch circuit using AWG #12 or #14 copper wire.
PAGE 7
Installation method - continuation Fix the installation panel onto the wall with 5 accessory mounting screws (5×30). Installation panel When installing on a concrete wall, use commercially available metal screw plugs. Mounting screws (5×30) (Accessories) Reinforce any walls made with materials other than concrete before installation. ※ When installing above a sink, the recommended B measurement is 23 1/16" (585mm) above the sink. ■ Installation position guide / " (22) Unit (in.
PAGE 8
Installation method - continuation English 1. Remove the drain tank. Drain tank 2. Open the front cover and remove the air filter. Tab Air ﬁlter Air ﬁlter ※ Refer to "How to open/close the front cover" (Page 13). 3 Main unit panel Open Pull the tab and open the front cover. 3. Remove the main unit panel mounting screw (1). 4. Unlock the upper tabs (2 locations) of the main unit panel, and remove the main unit panel from the base. Pull the tab and open the front cover.
PAGE 9
Installation method - continuation Caution Warning Input Power: 120 Vac Single-phase is used. Using the incorrect power supply may cause ﬁres, electric shocks or malfunctions. Wire the power cable to the terminal block. (No polarity) English Make sure that the main unit does not fall as the base is not attached to the wall with screws. Injuries may be caused if the unit falls off the wall. 4 15/16" (125) /2" (12) 1 1. Remove 1/2"(12mm) (single wire). ■ Single wire 2.
PAGE 10
Installation method - continuation 1. Place the power cable through the cord bushing and reattach it to the circuit case with the terminal block cover mounting screw. 2. Check that the power cable and wires are not pinched anywhere. Base English 6 Terminal block cover mounting screw Terminal block cover Cord bushing 1. Insert the "Motor lead wire" into the gap of ribs on the Base. Pull the tab for opening the front cover.
PAGE 11
Installation method - continuation 1. Open the front cover and attach the air filter. Air ﬁlter Main unit panel 3. Check that the front cover is securely closed. Caution 8 Check to see that the front cover is fitted securely. Press against the front cover so that it is firmly closed against the main panel. ※ Refer to "How to open/close the front cover" (Page 13). Gap 1 Front cover Drain tank ① Close the right side ② Close the left side (both the upper and lower parts) 4. Attach the drain tank.
PAGE 12
Test Run English Step What to check for Is the proper power being used? (JT-MC106G-W-NA type: Input Power: 120 Vac Single-phase ) 1 Check the power supply voltage 2 Turn the ground fault circuit interrupter on. 3 Turn the sensor switch is "ON". (page 4) Are any lights in the display on? 4 Insert your hands to check if air is being blow. (page 4) Is the air blowing? Turn the heater switch "ON".
PAGE 13
Initial setting checks ■ How to open/close the front cover How to open the front cover 1 Pull the tab for opening the 2 Hold the handle are on the 3 Open. front cover. right hand side of the main unit. Tab Main unit Front cover English Main unit Handle Pull Front cover Open How to close the front cover Caution Close the front cover with the procedures for opening it in reverse. Check to see that the front cover is fitted securely.
PAGE 14
Initial setting checks - Continuation ■ Turning the heater on 1 Open the front cover. Open Front cover 2 Press the heater switch or the maintenance English switch and let the settings light turn on. 3 Turn the heater switch "ON". Heater switch ※ The heater may not operate during continued use as there is the danger of scalding when the temperature of the warm air rises. The air may not feel warm when the room temperature is low (68 F (20 C) or below).
PAGE 15
Initial setting checks - Continuation ■ Turning the sensor off before maintenance 1 Pull the tab and open the front cover. Tab Pull Front cover Front cover 2 Open the front cover. Sensor light Sensor switch Open 3 Press the sensor switch and let the setting light turn on. 4 Turn the sensor switch "ON".
PAGE 16
English Tokyo Building 2-7-3, Marunouchi, Chiyoda-ku, Tokyo 100-8310, Japan − NA - 16 −