WD-52628 WD-62628 WD-73727 Projection Television Owner’s Guide TV Information Use this space to record the model number and serial number of your television. This information is on the back of your TV. Model Number Serial Number Purchase Date TM 5. visit our website at www.mitsubishi-tv.
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user of the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be sufficient magnitude to constitute a risk of electric shock.
FCC Declaration of Conformity Product: Projection Television Receiver Models: WD-52628, WD-62628, WD-73727 Responsible Party: Mitsubishi Digital Electronics America, Inc. 9351 Jeronimo Road Irvine, CA 92618-1904 Telephone: 949-465-6000 This device complies with Part 15 of the FCC Rules.
IMPORTANT SAFEGUARDS Please read the following safeguards for your TV and retain for future reference. Always follow all warnings and instructions marked on the television. 1. Read, Retain and Follow All Instructions Read all safety and operating instructions before operating the TV. Retain the safety and operating instructions for future reference. Follow all operating and use instructions. 2. Heed Warnings Adhere to all warnings on the appliance and in the operating instructions. 3.
IMPORTANT SAFEGUARDS, continued 12. Power Lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 13.
Contents Chapter 1: Television Overview TV Accessories.. . . . . . . . Special Features.. . . . . . . Front Control Panel. . . . . Remote Control Overview. . . . . . . . . . . Battery Installation . . Care. . . . . . . . . . . . . . . Sleep Timer.. . . . . . . . TV Back Panel.. . . . . . . . . Memory Card Reader. . . System Reset Button.. . . TV Reset Menu.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 4: NetCommand® Functions Device Selection Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the Device Menu Button to Display Menus. . . . . . . . . . . . . . Using the GUIDE Button to Display ChannelView™ and Menus. NetCommand®-Controlled Recordings. . . . . . . . . . . . . . . . . . . . . . Peer-to-Peer Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using A/V Discs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Our Thanks... Thank you for choosing Mitsubishi as your premier Home Entertainment provider This Owner’s Guide describes the features and functions of your Mitsubishi widescreen, high definition TV. We urge you to examine this Owner’s Guide to become familiar with the innovative features and operations this unique television offers. The very core of our corporate philosophy is to provide our customers with the very best.
Chapter . . . 1 Television Overview TV Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Special Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Front Control Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Remote Control Overview.. . . . . . . Battery Installation . Care.. . . . . . . . . . Sleep Timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TV Accessories Please take a moment to review the following list of items to ensure that you have received everything. $"#-& %#4 %57 7$3 %7% "6%*0 57 427 27 $) 70- 108&3 3. One Digital Audio Cable (sends the audio of digital channels to a digital audio/video receiver). 46# $"/$&- %&7*$& .65& 1"(& (6*%& 57 .&/6 %&7*$& .&/6 )0.& 7 $)*1 */'0 1*1 101 1*1 $) 1*1 %&7*$& "6%*0 7*%&0 &9$) 4-&&1 '03.
Special Features Your new High Definition widescreen television has many special features that make it the perfect center of your home entertainment system, including: High Definition DLP™ Display System Your widescreen Mitsubishi HDTV uses Texas Instruments most advanced Digital Light Processing™ technology for rear projection televisions. This TV is truly a high-performance multimedia monitor uniquely capable of both stunning high-definition video images and clear, detailed, high-resolution PC images.
Front Control Panel The shaded buttons on the front control panel are duplicated on the remote control. The top row of labels shows the control functions when there are no TV menus displayed on the screen. The bottom row of labels shows the control functions when the TV menus are displayed on the screen or when a special function has been activated. See “Remote Control Overview” for further details on the functions of these buttons. 2 3 4 o 70- o o $) o 108&3 -".1 45"564 5*.
Front Control Panel, continued Status Indicator Indicator Color TV Condition Additional Information None (indicator off) Normal TV on or standby condition. Normal operation. Yellow, steady Room temperature is too high. TV will not operate when the ambient room temperature is too high. Turn off the TV and wait until the room temperature drops. Red, either steady or TV may require service. blinking Turn off the TV and unplug the set from the AC power source.
Remote Control Overview Figure 1, following page 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 14 Slide Switch: Selects the A/V product to be controlled by the remote control. Select TV for NetCommand® device control. Numbers: Individually select channels or enter information into menus. SQV (SuperQuickView™): Scans through memorized lists of favorite channels. CH(ANNEL)/PAGE: Scans up or down through memorized channels.
Remote Control, continued 3 4 5 6 7 8 9 10 11 12 18 108&3 46# $"/$&- 427 %&7*$& 27 $) 70- Figure 2. Operation: Installing the Batteries .65& 1"(& (6*%& 57 .&/6 23 24 %&7*$& .&/6 )0.& */'0 1*1 101 1*1 $) 13 15 20 22 7 $)*1 "" BMLBMJOF CBUUFSJFT 21 1*1 %&7*$& 14 19 "" 2 17 $"#-& %#4 %57 7$3 %7% "6%*0 57 "" 1 2. Load the batteries, making sure the polarities (+) and (-) are correct.
TV Back Panel 3 COMPONENT INPUT 1 1 YPbPr (480i/480p/720p/1080i) 2 4 2 Y 5 INPUT S-VIDEO Pb VIDEO Pr AUDIOLEFT/ (MONO) AUDIOLEFT/ (MONO) AUDIORIGHT AUDIORIGHT OUTPUT DVI Analog Audio 1 AUDIO OUTPUT 2 VIDEO AUDIOLEFT/ (MONO) AUDIORIGHT MONITORLINK™/HDMI VIDEO 480i/480p/720p/1080i AUDIO PCM LINEAR 2 1 IR EMITTER Net Command¸ 1 ANT 1 / MAIN 10 ANT 2 / AUX DIGITAL AUDIO OUTPUT 1.
TV Back Panel, continued being shown on screen. Signals from digital channels and FireWire (IEEE 1394) devices are converted to analog signals. There is no video signal when copy restrictions are in effect. Audio alone is output when a Component input or the HDMI input is selected for recording. 7. HDMI™ 1 and 2 The HDMI (High Definition Multimedia Interface) supports uncompressed standard and high-definition digital video formats and PCM digital audio format.
Memory Card Reader and Front-Panel Inputs Memory Card Reader Models WD-52628, WD-62628 Figure 3 The memory card reader has four card slots that allow the display of JPEG pictures from many digital cameras and allow you to listen to MP3 or WMA audio files recorded from computers or other digital recording devices. The card slots are designed for the specific types of cards listed below. Other cards or objects should not be inserted into the slots as this may damage the TV.
Memory Card Reader and Front-Panel Inputs Input 3 and IEEE 1394 Input/Output Figure 4 These jacks allow for convenient connection of audio/ video devices to the front of the TV. Note that if you connect to the S-VIDEO terminal, the VIDEO terminal is deactivated. The VIDEO terminal is active only when there is no S-Video connection. Use the IEEE 1394 input/output to connect IEEE 1394 devices, such as some camcorders. This connection works the same as the rear IEEE 1394 connections.
Additional Information System Reset Button TV Reset Menu If the TV doesn’t respond to either the remote control or the front panel controls or will not power off, press the SYSTEM RESET button on the front panel with a pointed item such as the point of a ball point pen or end tip of a paperclip. 1. The TV will turn off and the green LED will flash quickly for about one minute. When the green LED stops flashing, you may turn on the TV again.
Chapter . . . 2 Connecting External Devices and NetCommand® Setup. . . . . . . . . . . . . . Using a CableCARD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wall Outlet Cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Standard Cable Box. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Antenna with a Single Lead. . . . . . . . . . . . . . . . . . . . . . . . . . Antennas with Separate UHF and VHF Leads. . . . . . . . . . . . .
Connecting External Devices and NetCommand® Setup NetCommand is able to control many current audio and video devices by sending remote control signals from the TV to each device through IR emitters. Additionally, it can learn the remote control signals used by most audio video devices not already in the TV’s memory. NetCommand can automatically switch the TV and compatible or learned Audio/Video (A/V) Receivers to the correct input used with each device.
Using a CableCARD Using a CableCARD After inserting a CableCARD into the TV back panel CableCARD slot and powering On the TV, the initialization process begins. An initial screen will automatically display for a few minutes, with information that your Cable Provider will need in order to start service. Please write down this information before calling your cable provider. Please call XYZ Cable at xxx-xxx-xxxx to activate cable service.
Connecting a Wall Outlet Cable or Cable Box Wall Outlet Cable Standard Cable Box (can be used with a CableCARD™) Figure 1 It is very important to connect the incoming cable for your primary viewing source to ANT-1, especially for CableCARD™ use and to download TV Guide On Screen® listings. 1. Connect the primary incoming coaxial lead cable to ANT 1/MAIN on the TV back panel. 2. For an optional secondary antenna source, connect an antenna (or cable) to ANT 2/AUX. 3.
Connecting an Antenna with a Single Lead or Antennas with Separate UHF and VHF Leads Antenna with a Single Lead Antennas with Separate UHF and VHF Leads (not for use with CableCARD™) Figure 3 Figure 4 A UHF/VHF combiner is required. This is not included with the TV, but is available at most electronics stores. For antennas with flat twin leads A 300-ohm-to-75-ohm transformer is required. This is not included with the TV, but is available at most electronics stores. 1. 1.
Connecting a VCR to an Antenna or Wall Outlet Cable Connecting VCR Audio and Video to the TV VCR to an Antenna or Wall Outlet Cable (Audio & Video) Figure 5 A two-way RF splitter, 3 coaxial cables, right and left audio cables, and an S-video or video cable are required. These are not included with the TV but are available at most electronics stores. 1. 5. Connect either an S-Video or Video cable from VIDEO OUT on the VCR back panel to INPUT-1 VIDEO on the TV back panel.
Connecting a VCR to a Cable Box (Audio & Video) VCR to a Cable Box (Audio & Video) connects to the L (left) channel. If your VCR is mono (non-stereo), connect only the white (left) cable. Figure 6 A two-way RF splitter, 4 coaxial cables, right and left audio cables and an S-Video or Video cable are required. These are not included with the TV but are available at most electronics stores. 1. 7. Connect the incoming cable to IN on the RF splitter. 2.
Connecting an A/V Receiver (Stereo System) Connecting a Satellite Receiver or Other Device with S -Video A/V Receiver (Stereo System) Figure 7 Most setups require either a digital audio cable or stereo audio cables. In some circumstances, you may need to connect both digital audio and stereo audio. A digital audio cable is provided with the TV. Stereo audio cables are not included. A.
Connecting a DVD Player with Component Video Connecting a DVI Device DVD Player with Component Video Figure 9 Component video cables and audio cables are required. These are not included with the TV. 1. Connect the Component Video cables from Y/Pr/ Pb VIDEO OUT on the back of the DVD player to COMPONENT-2 on the TV back panel, matching the correct connection: • Y to Y (Green) • Pr to Pr (Red) • Pb to Pb (Blue) 2.
Connecting an HDTV Cable Box or Satellite Receiver with Component Video Connecting an HDMI Device HDTV Cable Box or Satellite Receiver with Component Video Figure 11 A coaxial splitter, RCA component video cables, and audio cables are required. These are not included with the TV. 1. Connect the outside antenna, cable, or satellite to ANT or SATELLITE IN on the cable box or satellite receiver. See your device’s owner’s guide for instructions and cable compatibility. 2.
Connecting a Computer with an HDMI or DVI Monitor Output Computer with an HDMI Monitor Output Figure 13 An HDMI-to-HDMI cable is required. This is not included with the TV. It may be available at your local electronics retailer COMPONENT Connect an HDMI cable from HDMI 2 on the TV back panel to the PC’s HDMI output. HDMI devices provide video and audio through this cable, so no other connection is required.
Connecting the IR Emitter NetCommand® IR Emitter NetCommand® Figure 15 An IR emitter cable is included with the TV. • The emitter end being used can be secured in place using double stick tape. The emitters connected to these jacks are used by the NetCommand system and by TV Guide On Screen® to control other devices such as VCRs, DVD players, Cable boxes and Satellite receivers.
Connecting Compatible IEEE 1394 Devices Compatible IEEE 1394 Devices Compatible A/V devices include some, but not all, cable boxes, D-VHS VCRs, A/V discs, and future products. It is also possible to connect devices to the TV that have IEEE 1394 connectors but are not compatible with the TV or with the NetCommand® control system. Areas of compatibility to consider are: 1. Digital Video Signals The TV is able to decode MPEG2 and DV video as provided by some camcorders.
Connecting Compatible IEEE 1394 Devices, continued Connection Styles There are two different connection styles that can be used when connecting IEEE 1394 devices. Use the style that fits your network of audio/video products. 4-Pin-Style vs. 6-Pin-Style Connectors There are two different types of connectors used for IEEE 1394 terminals and cables: a 4-pin and a 6-pin style.
Helpful Hints for NetCommand Connections Q. My VCR (or other device) does not have two sets of stereo audio outputs. How can I connect this device’s audio to both the TV and the A/V Receiver? A. Connect the single set of stereo audio outputs to the TV only. Use Edit NetCommand® to change the setup of this device. In the Connection screen of “Change” make sure both audio and video for the TV input are check marked and the audio for the AVR input is not check marked.
Chapter . . . 3 NetCommand® Setup and Editing NetCommand® Introduction. . . . . . . . . . . . . . . Using the Remote Control with NetCommand® . NetCommand® Setup On-Screen Buttons. . . . . Menu System. . . . . . . . . 3D Graphical NetCommand® Initial Setup. . . . . . . . . . . . . . . Edit NetCommand®: Add an A/V Receiver. . . . . Edit NetCommand®: Add Devices . . . . . . . . . . Edit NetCommand®: Change or Delete Devices. IEEE 1394 Devices and NetCommand® Control..
NetCommand® Introduction NetCommand makes your TV the heart of your Home Theater NetCommand® is an intelligent control system that makes your Mitsubishi TV the heart of your home theater. With NetCommand, the TV sends signals to the other devices in the system via the IR emitters, telling the devices to play, record, change inputs, adjust volume, change channels and many more functions. All of this is accomplished with one remote control and without changing control layers.
Using the Remote Control with NetCommand® Below is a list of several manufacturers’ devices tested and shown to be compatible with NetCommand. These devices can be controlled without changing the setting of the remote control from TV to another product. NetCommand may be able to operate additional models, since many manufacturers use the same control signals to operate some or all of the models they offer. This chart lists only the models that have been tested with NetCommand.
NetCommand® Setup On-Screen Buttons To use the TV’s NetCommand feature, you need to provide some detailed information during the setup of your Mitsubishi TV. You must define the manufacturer of the devices that are connected to the television, or learn the IR code remote control signals for the device connected. For each device, the input to the TV and A/V receiver, and the names for the device are pre-set during Initial NetCommand setup.
3D Graphical Menu System Your TV also has Mitsubishi’s exclusive 3D Graphical on-screen operating system, which provides on‑screen information for menu choices and changes, using the TV’s remote control. Remote Control Buttons Menu Screens A picture (icon) is highlighted on the menu screen when selected with the ADJUST arrows. You may then make changes within the menu or access sub-menus, if available. You can also access sub-menus from a button.
NetCommand® Initial Setup The initial setup screens that appear when you first power on your new Mitsubishi TV guide you through setup of NetCommand and the TV Guide On Screen® system. Most IR remote control signal formats can be learned by NetCommand. Welcome Screen Figure 1 When you first turn on your TV, the NetCommand Welcome screen displays and asks you to select either English or Spanish as the language for the on-screen menus. The default language is English.
NetCommand® Initial Setup, continued Device Setup Screen TV Guide On Screen® System Setup If the devices connected to the TV are already in NetCommand memory, you can quickly select them at this screen. Press ADJUST or to move to each device type. Press ADJUST or to select the manufacturer. Select “Other” if the manufacturer is not listed. Later, you can use the Change setting in the Edit NetCommand menu to learn the remote control signals for this device.
NetCommand® Initial Setup, continued Review Screen Finish Screen After you have made your device choices, the Review Screen will display. It is important to review the settings to ensure that they are correct. If necessary, you can use
Edit NetCommand®: Add an A/V Receiver A/V Receiver Screen Figure 8 If your A/V Receiver manufacturer was not listed, and you selected “None” during the initial NetCommand setup, you may add the A/V Receiver and have NetCommand learn its remote control’s functions. Either select Edit from the Finish screen or, if you have finished the initial setup, go to the Main menu, select NetCommand, then press ENTER. The Edit NetCommand screen will display. Select Add. NetCommand to switch inputs to use this device.
Edit NetCommand®: Add an A/V Receiver, continued A/V Receiver (AVR) Input Learn Screen A/V Receiver (AVR) Learn Screen NetCommand can now learn the remote control signals used to select each input on the A/V receiver. 1. Figure 10 1. Press ADJUST or on the TV remote to select the check box for each function to be learned. 2. Press ENTER and the function name will begin to flash to confirm the ready-to-learn status. 3.
Edit NetCommand®: Add an A/V Receiver, continued Name Screen Finish Screen The Name screen allows you to change the default name for the A/V receiver to a custom name of up to eight characters (including a blank space), selecting from letters, numbers, and nine different characters. Using the TV’s remote, press ADJUST or to select each letter, then press ENTER to move to the next position. Press CANCEL to delete the current letter and move back one character position.
Edit NetCommand®: Add Devices Mitsubishi’s NetCommand allows you to edit your home theater configuration. You can add new devices, change device settings and connections, delete devices and learn remote control IR signals not already in NetCommand memory. Edit NetCommand Screen Add Screen If you selected Edit when you were at the Finish screen, the Edit NetCommand screen displays. Your choices are: Select “Add” from the Edit NetCommand screen, and the New Device screen will display.
Edit NetCommand®: Add Devices, continued [Device] Screen • Figure 17 If you selected “None” for a device type during initial setup, you can later add a device with this screen. This screen also opens when you select the Change option in the Edit NetCommand screen. Select “Other”, skip Learn and select Next>. This will allow the device to appear and will allow NetCommand to switch inputs to use this device. However, NetCommand will not be able to control this device.
Edit NetCommand®: Add Devices, continued to delete the current letter and move back one character position. When in the first position, the CANCEL button will return the name to the default name. Figure 18. [Device] Learn screen [Device] Advanced Learn Screen Figure 20. Name screen Figure 19 After learning the basic device keys, the [Device] Advanced Learn screen allows you to learn any special keys for your device. Most common IR remote control signal formats can be learned by NetCommand.
Edit NetCommand®: Add Devices, continued The screens described below may not be necessary for your device setup. If they do not display automatically on screen, they are not required. VCR for Recordings Screen Figure 22 Select the VCR to use for making analog recordings through NetCommand or the TV Guide On Screen® system. The VCR inputs must be connected to RECORD OUT on the TV, which outputs analog signals converted from digital. Figure 23.
Edit NetCommand®: Change or Delete Devices Change Device Screen Finish Screen Selecting Change from the Setup menu screen displays the Change screen. To change a device, select the device by name, not type. You can change the name or input connections to the TV and A/V receiver. If “Other” was selected for the manufacturer then you can also “Learn.” The rest of the screens that follow are the same as when you Add a device.
IEEE 1394 Devices and NetCommand® Control See pages 33 and 34 for information regarding compatible IEEE 1394 devices and connection styles. The TV is not able to control IEEE 1394 devices that use other types of control protocols. Incompatible digital audio, video and/or control information will still be able to pass from one device through the TV to another device on the network. These incompatible devices may not appear on the Device Selection menu or in the Review screen of the Edit NetCommand menu.
Adding IEEE 1394 Devices Automatically Adding IEEE 1394 Devices Automatically Name for 1394 Device Screen Addition of IEEE 1394 devices is a special case of NetCommand setup because the devices are detected automatically. You review, edit, and delete these devices through NetCommand just as you would any other devices. If you choose to add the discovered IEEE 1394 device, the Name for 1394 Device screen appears. Enter a new name for the device or use the default name that appears automatically.
Adding IEEE 1394 Devices Automatically, continued IEEE 1394 Device Type Screen Connection Screen If the new IEEE 1394 device is also connected using analog inputs, you will need to define the device type. Select the type of device, such as a VCR. Select the TV input that you used when you connected the video or S-Video cables. You may also select the TV or A/V receiver input you used when you connected the stereo audio cables.
Chapter . . . 4 NetCommand® Functions Device Selection Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the Device Menu Button to Display Menus.. . . . . . . . . . . Using the GUIDE Button to Display ChannelView™ and Menus. . NetCommand®-Controlled Recordings. . . . . . . . . . . . . . . . . . Peer-to-Peer Connections.. . . . . . . . . . . . . . . . . . . . . . . . . . . Using A/V Discs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Device Selection Menu When you press DEVICE on the TV’s remote control, the Device Selection menu (Figure 1) displays. If NetCommand® has not been set up, the Device Selection menu allows you to select an input for viewing. If NetCommand is set up, the Device Selection menu allows you to select the device for viewing, select audio from the TV speakers or A/V receiver, power compatible devices On or Off, and verify the destination of signals.
Using the Device Menu Button to Display Menus Device Menu If the input is a VCR or DVD, and NetCommand is set up, press DEVICE MENU once to display the transport menu for the current device (figure 3). Press DEVICE MENU a second time to display the menu for the current device source, if available. Figure 3. Transport menu When used with the TV Guide On Screen, DEVICE MENU displays or removes TV Guide’s menu information.
Using the GUIDE Button to Display ChannelView™ and Menus The GUIDE Button Please refer to the separate TV Guide On Screen® User’s Guide for details about using the GUIDE button with TV Guide On Screen. When you are not using the GUIDE for the TV Guide screens, pressing GUIDE allows you to see NetCommand® controlled program guides or menus.
NetCommand®-Controlled Recordings Setting up Recordings Record List Through NetCommand, you can automatically start and stop recordings and send signals from one playback device to a recording device. Recordings can be made on recordable devices connected to the TV. Press GUIDE while viewing the Record To screen to see a list of all currently programmed recordings. A maximum of 32 recordings can be scheduled.
NetCommand®-Controlled Recordings, continued Copy-Protected Material When attempting to record copy-protected material, the Record functions of the NetCommand and IEEE 1394 systems may be prevented or stopped. If you have a recording that is tagged “Record Once,” NetCommand will change the tag to “Record No More.” Restrictions for Traditional VCRs • Your VCR should be connected directly to the RECORD OUTPUT AUDIO and VIDEO outputs. • The VCR must be set manually to “Line Input.
Peer-to-Peer Connections What is a Peer-to-Peer Connection? Figure 9 A peer-to-peer connection allows the IEEE 1394 devices in your TV network to talk to each other without the further need of TV intervention once the peer-to-peer connection is established. With the connection established, you can turn off the TV or use it to watch another device. For example, the TV can set up a connection for an IEEE 1394 cable box that sends a program to another device for viewing.
Using A/V Discs A/V Disc Search NetCommand is able to search to a specific time in a recording on an IEEE 1394 A/V Disc. 1. Start the desired track’s playback on the A/V disc. 2. Use the number buttons to enter the time code position of hours followed by minutes. For example, to enter one hour and twenty-two minutes (1:22) into the track, enter 1, 2, 2. 3. Press ENTER to skip to the time code position. 4. To cancel the request or to start over, press CANCEL instead of ENTER.
Chapter . . . 5 TV Menu Operations Main Menu.. . . . . . . . . Setup Menu . . . . . . . . NetCommand® Menu . Record Menu.. . . . . . . Channel Menu .. . . . . . Captions Menu.. . . . . . V-Chip Lock Menu. . . . Audio/Video Menu. . . . Audio Settings. . . . . . . Video Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Main Menu Setup Menu Channel Menu Use the Setup menu to select English or Spanish as the language for the menus and on-screen displays. Memorize the available channels for antennas or cable connected to the ANT-1 and ANT-2 inputs. Manually set the time for the TV, or select Auto and the TV will automatically set the time based upon Extended Data Service (XDS) time data. This time data is usually broadcast by your local PBS station. This menu is also used to set the TV timer, and reset the lamp reminder.
Setup Menu Setup Menu Figure 8 After memorizing channels, the channels in memory can be accessed in ascending or descending order by pressing CH or . Select the Channel Menu to access further channel-editing features, such as channel add or delete, channel name, and SQV custom favorite channel memories. When you use a CableCARD™, the complete list of available channels is provided through the CableCARD.
Setup Menu, continued Time Zone Select your correct time zone. Press ADJUST or to select the time zone (Atlantic, Eastern, Central, Mountain, Pacific, Alaska or Hawaii) for your area. Then press ADJUST to move to the Daylight Savings time option. Daylight Savings Time Select the Daylight Savings time (DST) option that your state uses. Press ADJUST or to select Applies if your state or area uses DST, or Ignore if DST does not apply.
NetCommand® Menu NetCommand Menu Figure 11 Transport Menu Figure 13 $"#-& %#4 %57 7$3 %7% "6%*0 57 Figure 13. Transport Menu 108&3 NetCommand uses the Transport menu to control VCRs, VCRs, and similar DVDs, IEEE 1394 A/V Discs, digital devices. If you choose to turn off this menu when viewing 27 427 the devices, the transport buttons (rewind, play forward, stop, pause and record) on the TV’s remote control will continue to operate these devices.
Record Menu Record Figure 14 The Record menu allows you to set up recordings, view the record list, and set defaults for your recording devices. You cannot record from an analog channel or device or a VHS or S-VHS VCR to a digital recording device such as a DVCR or A/V Disc. Figure 15. Recording Setup screen Recording Now Can be used when viewing Antenna 1 or 2, an IEEE 1394 device, or a non-recording traditional device. Figure 14.
Record Menu, continued Record List Figure 16 To see a list of all currently programmed recordings, select the record list option on the Record menu or press GUIDE while viewing the Recording setup screen. A maximum of 32 recordings can be scheduled. To page through the list, press CH or . To Cancel Scheduled Recordings To remove a recording from the record list, use or to highlight the scheduled recording and then press CANCEL. To Cancel a Recording in Progress 1.
Channel Menu Channel Memory Figure 17 After the available channels have been memorized with Memorize Channels on the Setup menu, weaker channels can be added or unwanted channels can also be deleted. Press CH or on the remote control to see the channels in memory. Press ADJUST or to select Added or Deleted for the channel shown in the Channel number box. Name Analog channels shown on Antenna-1 or Antenna-2 can be named (up to four characters).
Channel Menu, continued SQV (SuperQuickView™) Removing SQV channels using the remote control: Figure 17 1. Using The Menu Screen SQV (SuperQuickView™) allows you to put together lists of your favorite channels from Antenna 1 and Antenna 2. You can store channels in any of the 9 different SQV memory banks. You can also store the same channel in multiple memory banks.
Captions Menu Background Captions Menu Figure 18 For analog channels, broadcasters can send either Standard or Text closed captioning. Standard Closed Captions follows the dialogue of the characters on screen and displays in a small section of the screen. Text Closed Captions often contain information such as weather or news and covers a large portion of the screen.
Captions Menu, continued Fonts • You can customize the text of digital captions by selecting the font of your choice.
V-Chip Lock Menu V-Chip Lock Menu Overview IMPORTANT Figure 20 The V-Chip Lock menu gives you access to three different types of TV locks. You must use a pass code to open this menu to enable/disable the lock options. The three different types of locks available are: • V-Chip Lets you restrict access to programming based on program-rating signals sent by the broadcaster. You can also set the time of day for these restrictions to be in effect.
V-Chip Lock Menu, continued 6. Press ADJUST to move to the Programs Not Rated box. Press ENTER to add or delete a check mark to allow or block programs that are not rated. NOTE: Use care when choosing to block unrated programming. News programs and emergency bulletins carry the “None” or “NR” (Not Rated) V‑Chip rating, and these are blocked with this option active. 7. Press ADJUST to move to the Movie Rating box. Press ADJUST or to select the movie rating level you want to allow.
V-Chip Ratings V-Chip Signal Information When provided by the broadcaster, V-Chip ratings can be used to control which programs can be viewed or will be blocked. When V-Chip ratings are sent, you will see the ratings when you change the channel or when you press the INFO button on the remote control. Both TV and Movie ratings will display. TV ratings apply to programs and movies developed for TV and may have supplemental blocking by content categories.
Audio/Video Menu Audio/Video Figure 23 When the original video was filmed on 30-frame-per-second cameras, the Auto setting automatically applies video decoding, the same as used with the Off setting. Film Mode is not effective for high-definition signals. TV Speakers When an A/V receiver has not been set up in NetCommand, this selection will turn the TV’s internal speakers on or off. You may select Off when sending the sound through a separate stereo system or surround sound A/V receiver. Figure 23.
Audio Settings NOTE: The effects of the audio settings of Bass, Treble, Balance and Surround affect the sound heard through the TV speakers only. be related to the program you are watching, (such as a sound track in a foreign language), or it might be unrelated (such as a weather report). If an SAP signal is broadcast, the letters “SAP” are displayed when you tune to the channel. Mono: Reduces background noise. Use when receiving a weak stereo audio signal. All audio is played mono with this setting.
Video Settings Video Settings adjusting. Each TV input or device has a memory for PerfectColor. While using the PerfectColor option, press CANCEL if you want to reset the colors to the default settings. Press the VIDEO key repeatedly to cycle through the Video options to the one you want to change. Use ADJUST to change settings.
Chapter . . . 6 Additional Features MediaCommand™ and Memory Card Playback.. Operation of PIP and POP. . . . . . . . . . . . . . . . . TV Display Formats.. . . . . . . . . . . . . . . . . . . . . PC Viewing. . . . . . . . . . . . . . . . . . . . . . . . . . . PC Display Formats. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MediaCommand™ and Memory Card Playback Warning: Some memory cards available on the market are not properly certified to follow the card type specifications noted below and cannot be used by the card reader. If you experience problems with the reading of your file, please transfer your files to a properly certified card. Memory Card Slots Inserting a memory card 1. Insert a card into a matching card slot on the front of the TV. Be sure to use the correct card slot. Card 1 accepts SmartMedia™.
Media Command™ and Memory Card Playback, continued For MP3 or WMA7 Playlist Menu: Figure 3 1. Press GUIDE to display the Playlist menu. 2. Press ADJUST or to select different tracks (CH up/down will change pages of the Playlist). Use REW to go to the first track on the page and FF to go to the last track on the page. 3. Press PLAY to begin playback. The Playlist menu will be taken down. The song currently playing will be highlighted. Figure 3.
Operation of PIP and POP You can display programs from analog channels, analog inputs, or analog devices as picture-in-picture (PIP) and picture-outside-picture (POP). The TV has a second analog tuner for non-scrambled analog channels received on ANT‑1 and displays them as the PIP/POP sub-pictures. Digital channels and devices can be shown as the main picture but cannot be the sub-picture. PC screens can be viewed as the main picture with PIP. Press PIP/POP to activate the PIP/POP option.
TV Display Formats This is a widescreen TV, also known as a 16:9 TV. This shape reflects the new types of images available from HDTV and many DVDs. There are still many older style narrow-screen images (called 4:3 aspect ratio) you will encounter. While there will never be a perfect solution for displaying a narrow image on a wide screen, Mitsubishi offers several display formats from which to choose. Press FORMAT on the TV remote control to cycle through the available display formats.
TV Display Formats 03*(*/"- 4*(/"- "OBNPSQIJD %7% 03*(*/"- 4*(/"/PO BOBNPSQIJD PS 4% 57 %JTQMBZ 57 %JTQMBZ 4UBOEBSE 4UBOEBSE OPU SFDPNNFOEFE EJTUPSUFE SFDPNNFOEFE OPU BWBJMBCMF GPS )% 4% PS BOBMPH Q J &YQBOE &YQBOE OPU BWBJMBCMF GPS )% 4% PS BOBMPH Q J SFDPNNFOEFE GPS MFUUFSCPYFE OPU SFDPNNFOEFE EJTUPSUFE OPU BWBJMBCMF GPS )% 4% PS BOBMPH Q J ;PPN ;PPN OPU BWBJMBCMF GPS
PC Viewing Figure 1 To display your PC screen on the TV, first connect the PC to the HDMI 2 input on the TV’s back panel (see Chapter 2). You must then activate the PC option in NetCommand. You can do this during initial NetCommand setup by selecting the PC option in the Device Setup screen. To do this at any time afterwards, use the NetCommand Add function. You will then be able to select the PC through the Device Selection Menu.
PC Display Formats Signal Format Original Pixel Counts 16 X 9 Standard 4 X 3 Standard 1696 X 960 1280 X 960 1696 X 960 1280 X 960 1702 X 960 1280 X 960 1702 X 960 1280 X 960 Standard Zoom 1024 X 768 1280 X 960 1280 X 720 1706 X 960 VGA 640 X 480 WVGA 848 X 480 SVGA 800 X 600 WSVGA 1064 X 600 Signal Format Original Pixel Counts XGA 1024 X 768 PC720p 1280 X 720 90 Chapter 6.
Chapter . . .
General TV Operation Symptom Suggested Solution 1. The TV remote control does not work. • • • • Check that the batteries are installed correctly. Check that the selected switch is set to “TV.” Be no more than 20 feet from the TV when using the remote control. Program the remote control to operate the TV (Appendix D). 2. The TV takes several seconds to respond. • • • • It is normal for digital channels to take longer to tune in. Press ENTER after a channel number to avoid delays.
General TV Operation Symptom Suggested Solution 14 A device does not respond to button presses from the remote. • Remote has not been set up for NetCommand® use. • The incorrect manufacturer was selected during setup. Select the Change setting from the Setup menu and then the device to display the manufacturer selection. Change if necessary. • The device is not supported and keys have not been learned. • The requested function is not supported by NetCommand.
General TV Operation Symptom Suggested Solution 26. The message “Lamp will soon exceed...” keeps displaying after the lamp has been replaced. Reset the lamp reminder in the setup menu. 27. NetCommand unable to learn specific device keys. • Device does not use IR format for remote control signal. ITT and RF formats cannot be learned. • Room lighting may affect the signal. Have the remotes very close (6 inches or less) to the TV during Learning.
Sound Symptom Suggested Solution 1. There is no sound even when the volume is turned up. • • • • Check audio source in Device Menu. Check to see if the MUTE button is on. The TV’s “Listen to:” setting may be set to SAP. Check that the “TV Speakers” setting is On in the Audio/Video menu. 2. The sound does not match the screen picture. • • • • NetCommand® is set up incorrectly. The TV’s “Listen to:” setting may be set to SAP. If using stereo or A/V receiver speakers, check their input selection.
IEEE 1394 Devices Symptom Suggested Solution 1. Excessive digital artifacts when viewing an IEEE 1394 device. • The IEEE 1394 cable is too long; 15 feet between devices is the maximum. • There may be a slow device in the middle of the IEEE 1394 network. Move the slow devices to the end so that connections for faster devices do not pass through them. 2. D-VHS recordings for digital cable have drop-outs (loss of picture or sound), or no playback.
IEEE 1394 Devices Symptom Suggested Solution 10. Cannot record to or from the IEEE 1394 device, including dubbed recordings. • To initiate a recording to IEEE 1394 device, press the REC key. The Record menu displays allowing setup of the recording. • The source device for the recording is not powered on. • When dubbing, the destination device for the recording is not powered on. • The wrong medium (analog tape for digital recording, or digital tape for the analog recording) is in the device.
Appendices Appendix A: Appendix B: Appendix C: Appendix D: Appendix E: Appendix F: Appendix G: Appendix H: Appendix I: Specifications.. . . . . . . . . . . . . . . . . . . . On-Screen Information Displays. . . . . . . . Bypassing the V-Chip Lock. . . . . . . . . . . Remote Control Programming Codes. . . . Device Control with NetCommand®. . . . . NetCommand® Specialized Device Keys. . Cleaning and Service.. . . . . . . . . . . . . . . Lamp Cartridge Replacement.. . . . . . . . .
Appendix A: Specifications From time to time, Mitsubishi may offer software updates to expand the features or operation of this TV. When these updates are available they will be announced on our web site, Mitsubishi-tv.com. If you return your owner’s registration card, with your model and serial number, you may receive written notification of available software updates. TV Specifications Projection System DLP, 0.
Appendix A: Specifications, continued Audio Inputs: Qty. 7 pairs RCA Pin Plug 500 mV (full scale), 43-k ohm Outputs Video, Qty. 1 Signal Type Audio:, Qty. 2 pairs Video: RCA Pin Plug 1.0 Vp-p, 75-ohm NTSC 480i only RCA Pin Plug, 500 mV rms + 200 mV (full scale) for analog sources, 1.5 Vrms + 0.5 Vrms (full scale) for digital sources. Digital Interfaces: Digital Audio Output, Qty. 1 RCA Pin Plug, Signal Type, Dolby Digital, PCM IEEE 1394, Qty.
Appendix B: On-Screen Information Displays When you turn on the TV, change devices, change channels, or when you press the INFO button on the remote control, the TV will display the current status. Below are the most common displays. Please note that seldom or never do all of the different status indicators appear at the same time. Analog Program 1. Antenna or Device being viewed 2. Analog channel being received: If antenna being viewed 3. Channel name (if manually programmed) 4.
Appendix C: Bypassing the V-Chip Lock Lock Bypass Instructions Have Been Filed for Future Reference Bypassing the V-Chip Lock After you set the lock, you need your pass code to view a V-Chip locked program, view the locked TV, cancel the lock, or enter the V-Chip Lock menus. If you forget your pass code, you can view the locked TV without entering your pass code. When you are prompted for your pass code, press the number 9 and QV buttons on the TV remote control at the same time.
This page intentionally blank 104 Appendices
Appendix D: Remote Control Programming Codes IMPORTANT The remote control may return to its initial setting when the batteries are changed. You may need to reprogram. Programming the Remote to Control NetCommand A/V Products 1. Move the slide switch at the top of the remote to the TV position. 2. Press and hold POWER on the remote control. 3. Enter the three digit code of 935, and then release POWER. 4.
Appendix D: Remote Control Programming Codes, continued Cable Boxes, continued SCIENTIFIC ATLANTA SIGNATURE SLMARK SPRUCER STARCOM STARGATE TELEVIEW TOCOM TOSHIBA UNIKA UNITED CABLE UNIVERSAL VIDEOWAY VIEWSTAR ZENITH DVD Players DVD Brand MITSUBISHI AIWA APEX BOSE DENON FERGUSON HARMAN KARDON HITACHI JVC KENWOOD MINTEK NORDMENDE ONKYO ORITRON PANASONIC PHILIPS/MAGNAVOX PIONEER RCA/GE/PROSCAN ROTEL SABA SAMSUNG SAMPO SHARP SYLVANIA SONY THOMSON TOSHIBA V INC.
Appendix D: Remote Control Programming Codes, continued IMPORTANT Some manufacturers may change their products, or they may use more than one remote control system. If this is the case, the TV remote control may not be able to operate your VCR, DVD, cable box, satellite receiver, or A/V receiver. After entering the correct codes in each position of the remote control, use the slide switch to select which product will respond when an operational button is pressed.
Appendix E: Device Control with NetCommand® NetCommand Compatible Traditional Devices (Analog) When Device Selection Menu is Displayed and the Device is Highlighted (Yellow Outline) A/V RECEIVER VCR DVD CABLE BOX/SAT POWER Power On/Off (toggle) Power On/Off (toggle) Power On/Off (toggle) Power On/Off (toggle) GUIDE Changes between digital and analog audio Changes VCR inputs n/a Changes antenna inputs (RCA model DTC-100 only) FORMAT n/a n/a Changes output between interlaced and progressive
Appendix E: Device Control with NetCommand®, continued IEEE 1394 Devices When Device Selection Menu is Displayed and the Device is Highlighted (Yellow Outline) TUNER/ CABLE BOX/ SAT A/V DISC DVCR AMPLIFIER POWER Power On/Off (toggle) Power On/Off (toggle) Power On/Off (toggle) Power On/Off (toggle) GUIDE n/a n/a n/a n/a FORMAT n/a n/a n/a n/a Device Remote Control Button When an IEEE 1394 Device is Viewed or Played Device CABLE/SAT TV Disc or A/V DISC DVCR AMPLIFIER Channel up/down
Appendix F: NetCommand® Specialized Device Keys A/V RECEIVER CABLE or SAT VCR DVD LEARNING SCREEN CHECK BOX NAME FUNCTION NAME ON TV REMOTE X X X X Power* Power On or Power On/Off POWER** X X X X Power (Off)* Power Off POWER** X Volume Up Volume Up VOL X Volume Down Volume Down VOL X Mute Mute MUTE X Analog to Digital* Analog/Digital Switch GUIDE** X Digital to Analog* Digital/Analog Switch GUIDE** X Input (1-7) AVR Input Select Automatic (when device is selected)
Appendix G: Cleaning and Service IMPORTANT DO NOT use any kind of abrasive cleaner on the surface of the TV screen. Cleaning Normally, light dusting with a dry, non-scratching duster will keep your TV clean. If cleaning beyond this is needed, please use the following guidelines: First, turn off the TV and unplug the power cord from the power outlet.
Appendix H: Lamp Cartridge Replacement CAUTION BURN DANGER! During normal operation, the surfaces inside the TV near the lamp are extremely hot. TOUCH THE LAMP CARTRIDGE BY THE HANDLE ONLY Do not touch the glass parts of the lamp cartridge. CAUTION: If the television is on, press POWER to turn it off. Allow the television to cool for one hour before attempting to replace the lamp cartridge. LAMP The light source for this television is a lamp, which is part of a lamp cartridge assembly.
Appendix H: Lamp Cartridge Replacement, continued WARNING THE GRILLE/COVER IS PROVIDED WITH AN INTERLOCK TO REDUCE THE RISK OF EXCESSIVE ULTRAVIOLET RADIATION. DO NOT DEFEAT ITS PURPOSE OR ATTEMPT TO SERVICE THE TV WITHOUT REMOVING THE GRILLE/COVER COMPLETELY. 1. Turn TV power off and allow the lamp to cool at least one hour before proceeding. 2. After the lamp has cooled, remove the plastic air exhaust grille/cover by removing two screws with a #2 (large) Phillips screwdriver. See figure 1. 3.
Appendix I: Recording and Viewing Combinations The tables in this appendix show which program sources you can watch while a recording is in progress.
Appendix I: Recording and Viewing Combinations Digital VCR or A/V Disc Connected to IEEE-1394 Port When recording this (source device) You can watch any one of these (viewing device) Same as Recording Ant-1 Air/Cable Analog Channel Ant-1 Air/Cable Digital Channel Yes Yes IEEE-1394 Device HDMI Device No Yes Yes Yes Yes No Yes Yes Yes Yes Cannot make digital recordings from this source Yes Input 1–3 Video or S-Video Devices IEEE-1394 Device Component 1–3 Devices Cannot make digital record
Trademark and License Information LICENSOR’S SUPPLIERS DO NOT MAKE OR PASS ON TO END USER OR ANY OTHER THIRD PARTY, ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY OR REPRESENTATION ON BEHALF OF SUCH SUPPLIERS, INCLUDING, BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, TITLE, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. CableCARD™ is a trademark of Cable Television Laboratories, Inc. CompactFlash® and CF are trademarks of the CompactFlash Association.
MITSUBISHI TV SOFTWARE END-USER LICENSE AGREEMENT FOR EMBEDDED SOFTWARE IMPORTANT – READ CAREFULLY: This License Agreement is a legal agreement between you (either an individual or an entity) and Mitsubishi Digital Electronics America, Inc. (MDEA) for all software pre installed and/or provided along with this television (“Software”). By utilizing this television and Software, you agree to be bound by the terms of this License Agreement.
Mitsubishi DLP™ Projection Television Limited Warranty MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC. (“MDEA”) warrants as follows to the original purchaser of this television from an authorized MITSUBISHI Audio/Video Dealer, should it prove defective by reason of against defects arising from improper workmanship and/or material: a. Parts. The lenticular (i.e.
d. To obtain a replacement lamp during the warranty period, please contact the MDEA Consumer Relations Department at (800) 332-2119. After the warranty period you may order the lamp directly from the MDEA Parts Department at (800) 553-7278. 2. THIS LIMITED WARRANTY DOES NOT COVER: a. Up to .01% pixel outages (small dot picture elements that are dark or incorrectly illuminated). b.
Index A A/V Memory Reset. See Reset A/V Receiver Adding 45 Connecting 28 Inputs 45 Input Learn Screen 46 Learn Screen 46 A/V Reset. See Reset A/V Settings Descriptions Audio 80 Video 81 Accessories, TV 10 Add Device. See NetCommand Advanced Learn Screen, [Device] 50 Antenna inputs (ANT-1 MAIN, ANT-2 AUX) 16 Antenna with Leads, Connecting 25 Audio/Video Menu 66, 79 Audio Inputs 16 B Back Panel (illustrated) 16 Batteries.
Device Setup Screen 43 Edit NetCommand Screen 48 Initial Setup 42 NetCommand Menu 69 Pre-Memorized Devices 39 Specialized Device Keys 110 O On-Screen Information 102 P Pass Code Resetting 103 Setting 76 PC 16, 17, 48, 54, 87 Connecting 31 Viewing 81, 89 Peer-to-Peer Connection 63 PerfectColor 81 PIP (Picture in Picture) 86 PIP Device Selection Menu 58 Playlist Menu, MP3 or WMA7 85 Q QV (QuickView™) 14 R Recording Analog VCR and Viewing 114 Cancel Current Recordings 71 Default Digital (Record) Device
Website: www.mitsubishi-tv.com E-mail: MDEAservice@mdea.com To order replacement or additional remote controls, lamp cartridges, or Owner’s Guides, call 800-553-7278 For questions, call Consumer Relations at 800-332-2119 © 2005 Mitsubishi Digital Electronics America, Inc. 853B540B30v3 Written and Printed in U.S.A.
