DATA PROJECTOR MODEL XD60U User Manual IMPORTANT * DLP™ (Digital Light Processing) and DMD (Digital Micromirror Device) are registered trademarks of Texas Instruments Incorporated (U.S.A.). * VGA and XGA are trademarks or registered trademarks of International Business Machines Corporation (U.S.A.). * S-VGA is a registered trademark of Video Electronics Standards Association. * Microsoft, Windows, and PowerPoint are registered trademarks of Microsoft Corporation (U.S.A. and other countries).
IMPORTANT SAFETY INFORMATION CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.
IMPORTANT SAFETY INFORMATION Please read all these instructions regarding your projector and retain them for future reference. Follow all warnings and instructions marked on the projector. 1. Read instructions All the safety and operating instructions should be read before the appliance is operated. 2. Retain instructions The safety and operating instructions should be retained for future reference. 3. Warnings All warnings on the appliance and in the operating instructions should be adhered to. 4.
IMPORTANT SAFETY INFORMATION WARNING: Unplug immediately if there is something wrong with your projector. Do not operate if smoke, strange noise or odor comes out of your projector. It might cause fire or electric shock. In this case, unplug immediately and contact your dealer. Never remove the cabinet. This projector contains high voltage circuitry. An inadvertent contact may result in an electric shock.
Major Features 䡵 Lightweight (at about 1.5 kg/3.3 lb) high-intensity mobile projector The synergy of the DLP™ (Digital Light Processing) display system and our own optical design serve to improve the optical utilization efficiency. The three primary colors (RGB) required in color expression are reproduced with one DMD (Digital Micromirror Device of high precision). These factors have enabled a design that offers both high intensity and small size/ lightweight features.
Table of Contents Preparation and Background Knowledge IMPORTANT SAFETY INFORMATION ............................................................................ E-1 Major Features ................................................................................................................. E-4 Table of Contents ............................................................................................................. E-5 Checking the Supplied Accessories ................................................
Table of Contents Menu Operations Menu Operation Method ................................................................................................ Names and Functions of Buttons Used for Menu Operations ................................... Menu Screen Names and Functions ......................................................................... Performing Menu Operations ....................................................................................
Checking the Supplied Accessories Remove the main unit and the accessories from the box and check that the following items are included. Power cable (1.8 m / 5.9 feet) [3] This power cable supplies power to the unit. See Page E-21 about connections. No. 246C484-10/No. 246C484-20/No.
Checking the Supplied Accessories Carrying case (for projector and accessories) [1] This is a case designed for storing the projector and its accessories. Use this carrying case when storing or moving the projector. No. 772C019-10 HOW TO PUT THE PROJECTOR INTO THE CARRYING CASE Close the lens shutter or lens cap before putting the projector in its case, then fasten the projector in place with the Velcro belt. Place the accessories in the storage pocket.
S U AT ST AN ST BY D CE R U SO AU TO U EN M K IC U U Q EN M Names of the Main Unit Parts Exhaust vents Focus ring [E-25] Zoom ring [E-24] Remote control sensor [E-12] Lens Front adjuster button [E-25] (There is also one on the right side.) Lens cap Remove before use. Attach the lens cap after use to protect the lens.
Names of the Main Unit Parts STANDBY button [E-21] STATUS STATUS indicator [E-21, 55] STANDBY Buttons used in menu and quick menu operations [E-34, 35] STANDBY indicator [E-21, 55] SELECT (왖왔왗왘) buttons SOURCE AUTO SOURCE button [E-26] AUTO button [E-26] ENTER button [E-22] MENU button [E-35] QUICK MENU button [E-34] QUICK MENU MENU Speaker Remote control sensor [E-12] Y DB AN ST US AT ST TO AU E C UR ICK U QUMEN SO Built-in security slot (See description below.
2 L O V N T S K 3 Infrared transmitter [E-12] STANDBY button [E-21, 23] This button is used to switch ON the power and set the unit to the STANDBY mode. Buttons used for input selection [E-26] RGB button and VIDEO button (VIDEO / S-VIDEO) MUTE button [E-28] (Temporarily cancels the video and audio) Number buttons [E-32] (Used for the security lock.
Preparing the Remote Control Button Battery Replacement Using the remote control for the first time The battery compartment is fitted with a transportation insulation sheet at the time of shipping. Pull out the sheet and remove it. The remote control is now ready for use.
The Procedure Up to Projecting to the Screen Perform setup adjustments in the following order. 1 Position the projector Determine the locations to set up the screen and the projector. See “Placement Guide” on Page E-14. 2 Connect the video equipment and personal computer Connect your equipment to the projector. When making connections with the personal computer’s DVI connector or RGB connector, see “Connections with Personal Computers” on Page E-15.
Placement Guide • Use this information as a guide to find out about the screen size when the projector is placed at a certain location, or to find out the approximate size of a screen that will be required. • The projection distance over which focussing is adjustable is 1.20 m (3.9 feet) to 14.17 m (46.50 feet). The projector should be placed within this range.
Connecting Personal Computers and Video Equipment Connecting this unit with a personal computer permits presentation data to be projected as a large screen display at conferences, lectures, and on other occasions. Furthermore, connecting this unit to a DVD player or other video equipment source in combination with an audio/video amplifier and speaker system will allow you to enjoy convincing home theater.
Connecting Personal Computers and Video Equipment Personal Computers with a Mini D-Sub 15-Pin Connector • When making connections with the DVI connector of the projector, please make the connection via the supplied DVI/mini DSub 15-pin conversion cable. The projector has been set to “Auto” at the factory; however, if it does not project, please change the input setting to “RGB” using the menu sequence of [Setup] → [Input Format] → [PC]. See “Input Format” on Page E-50.
Connecting Personal Computers and Video Equipment To Output the External Output Signal of a Notebook Computer When projection will be with a notebook computer connected, knowledge will be required for the cable connection and notebook computer startup procedure as well as the operation that follows notebook startup. Please consult the instruction manual of your notebook computer or the on-line help while performing the following procedure.
Connecting Personal Computers and Video Equipment Connections with Composite Signals Video Equipment with VIDEO Connectors • Make the connection to the VIDEO connector of the projector using the supplied Video cable. • The input setting of the VIDEO connector has been set to “Auto” at the factory; however, if the projector does not project, please change the input setting to “Your Country’s Television Broadcast System” using the menu sequence of [Setup] → [Input Format] → [Video].
Connecting Personal Computers and Video Equipment Connections with Component Signals When the Video Equipment Has a YCbCr Connector or YPbPr Connector • The projector has been set to “Auto” at the factory; however, if it does not project, please change the input setting to “Component” using the menu sequence of [Setup] → [Input Format] → [PC]. See “Input Format” on Page E-50. • This projector automatically distinguishes the YCbCr input signal and the YPbPr input signal and projects it.
Connecting Personal Computers and Video Equipment Connections with Audio Connectors * Make the connection to the projector’s AUDIO connector using the supplied audio cable. When the audio jack of the equipment that is to be connected is of the RCA phono type, make connection via the supplied audio conversion cable. * The built-in speaker of the projector provides monaural audio. To enjoy convincing audio reproduction, please connect the audio output of the video equipment to your audio system.
Power Cable Connections and Switching the Power On/Off There is an order in which the power cable is connected and the power is switched on/off. Operating 1 Connect the AC IN connector of the projector and the power outlet using the supplied power cable. The STANDBY indicator will light in amber, and the unit will enter the standby mode. Lit amber STANDBY ST AN D BY STATUS SO U Q M UI EN CK U R CE AU TO ST AT U S To wall outlet M EN U Firmly plug in all the way.
Power Cable Connections and Switching the Power On/Off When [Menu Language Select] is Displayed Upon Switching On the Power The first time the power is switched on after purchase, [Menu Language Select] will be displayed. Follow the procedure described below and select the display language of the projector. If the image is blurred, turn the focus ring counterclockwise or clockwise to focus it. See Page E-25.
Power Cable Connections and Switching the Power On/Off Finishing 1 Switch off the power of the connected equipment 2 Switch off the power of the projector Main unit operation: Press the STANDBY button. Remote control operation: Press the STANDBY button. STANDBY MENU ENTER RGB VIDEO CANCEL QUICK Q FREEZE 1 MUTE LAMP MODE AUTO 2 3 Power Off 4 OK ? ASPECT The [Power Off] display appears.
Adjustment of the Projection Screen Switch on the power of the connected equipment and make the adjustments with the video signal being input to the projector. Adjustment of the Projection Screen 1 Turn the zoom ring to adjust the screen size of the projection image. Adjust the image to match the desired screen size. When outside of the adjustment range, move the projector to the rear or forward. Zoom ring 2 Adjust the projection image to the screen. Check that the screen is set level and vertically.
Adjustment of the Projection Screen 3 Turn the focus ring and adjust the focus of the screen Focus ring XD60 U EN M CE R U SO TO AU S U AT ST BY D AN ST Raising the projection image While viewing the projection image, (1) press and hold the front adjuster buttons located at the left and right and, (2) raise the projector to align the image with the screen, then release your fingers. Turn the left and right front adjusters for fine adjustment. Adjust so that there is no shaking of the projector.
General Operation This section describes the use of direct operation with the main unit or remote control buttons. For information about operation using the menu, see "Menu Operation Method" on Page E-35 and the various items on Pages E-42 to E-54. Input Selection This operation selects the input signal to be projected. Main unit operation: Press the SOURCE button. (It will not function while the menu or the quick menu is displayed.
General Operation Selection of Aspect Ratio This function selects horizontal and vertical picture proportions of the input signal. STANDBY MENU ENTER RGB Press the ASPECT button while viewing the projected image and select the aspect ratio. VIDEO CANCEL QUICK Q Personal Computer Signal Each press of the ASPECT button advances the selection one step in the sequence of Auto → Direct → Real, and then repeats. FREEZE 1 MUTE LAMP MODE AUTO 2 3 4 ASPECT VOL KSTN ZOOM TIMER Auto ............
General Operation Freezing a Moving Picture This function is used to stop and view a moving picture. Note that the input image continues to advance even though the picture there is a still picture condition. STANDBY MENU ENTER RGB VIDEO CANCEL QUICK A press of the FREEZE button changes the screen to a still picture. A further press returns the screen to a moving picture.
General Operation Keystone Use this to adjust for trapezoidal (keystone) distortion of the projected image. STANDBY MENU ENTER RGB Adjustment Method (1) Press the 왖 or 왔 KSTN button to make the left and right sides parallel. The keystone adjustment display appears when one of the buttons is pressed. VIDEO QUICK CANCEL Q (2) FREEZE 1 MUTE LAMP MODE AUTO 2 3 4 ASPECT VOL KSTN ZOOM TIMER (1) Press the “왔” button. Press the “왖” button.
General Operation Enlargement of the Image and Video Movement This function digitally enlarges the personal computer image and video image. STANDBY MENU ENTER RGB (1) Press the ZOOM button to enlarge the image. The zoom display appears when the ZOOM button is pressed.
General Operation Using the Presentation Timer The presentation is given while checking the timer displayed on the screen. The gauge display allows the remaining time to be known at a glance. (1) Press the TIMER button to show the settings display. The display will close when an operation has not been made for about 10 seconds.
General Operation Protecting the Projector with the Security Lock A password can be registered and the security lock set in order to protect the projector from unauthorized use. Registering the password The password is registered using the menus. For instructions on operating the menus, see “Menu Operation Method” on E-35. (1) Select “Security Lock” in the “Option” menu and set it to “Enable”. The menu closes and the password registration display appears.
General Operation If the password input display appears when the power is turned on When a password has been registered, the “Password” input window appears on the projected image when the power is turned on. The projector continues projecting this image until the correct password is input. At this time, only the STANDBY button (power off) works. Use the procedure described below to input the registered password. For instructions on registering the password, see E-32.
General Operation Using the Quick Menu (1) This function permits frequently used adjustments to be performed quickly. Note that the Quick Menu will not be displayed unless the signal of the connected equipment is input. Please select the input that you wish to adjust. Main unit operation (1) Press the QUICK MENU button to display the quick adjustment display. Further presses cause the adjustment display to change in sequence. Press the SELECT 왖 or 왔 button to switch to the desired adjustment display.
Menu Operation Method • This section describes only the menu operation method. Please see this item should you need information while performing menu operations. • For information about a menu function, adjustment, or setting, please see one of the pages containing such descriptions. • Adjustments and settings are made by projecting an image and adjusting to an optimum condition. • The remote control should be pointed toward the remote control sensor of the projector and operated.
Menu Operation Method Menu Screen Names and Functions Menu Name This is the title of the menu. There is a change to the title screen when the menu is selected. The cursor moves to the selected menu name. Cursor (Deep Blue) This permits setting/adjustment of the item located at the cursor position. Item Name This is the name of the adjustment or setting. Icon: Pressing the ENTER button displays the sub menu or setting contents.
Menu Operation Method Performing Menu Operations • Only “Setup”, “Options” and “Info.” can be selected when no signal is being input. • The menu display will close if, after pressing a button, the next button operation is not made within 30 seconds. • The adjustment and the setting values are stored even when the power is switched off or the plug is disconnected from the power outlet. (Note that some items are not stored.
Menu Operation Method Displaying the Cursor 3 Press the 왔 SELECT button to display the item name selection cursor. STANDBY MENU ENTER RGB VIDEO CANCEL QUICK Q FREEZE 1 MUTE LAMP MODE AUTO 2 3 4 ASPECT VOL KSTN ZOOM TIMER This condition allows selection of the item name.
Menu Operation Method Closing the Menu 6 Press the MENU button and close the menu display STANDBY MENU ENTER RGB VIDEO CANCEL QUICK Q FREEZE 1 MUTE LAMP MODE AUTO 2 3 4 ASPECT VOL KSTN ZOOM TIMER Selecting Another Menu Name with Remote Control Operation When a sub menu is displayed, press the CANCEL button and close the sub menu. Press the CANCEL button again to turn off the item name cursor.
Menu Operation Method List of Item Names Offering Input Selection and Adjustments/Settings The item names that can be adjusted/set will differ depending on the input signal.
Menu Operation Method Imput Terminal EO D VI g ita p Sub Menu Item Name VIDEO R G lR B D EO GB u om t Si gn A pon al na lo ent PC Auto Source 嘷 嘷 嘷 嘷 嘷 E-49 Auto Power Off 嘷 嘷 嘷 嘷 嘷 E-49 Menu Position 嘷 嘷 嘷 嘷 嘷 E-49 Lamp Mode 嘷 嘷 嘷 嘷 嘷 E-50 PC 嘷 嘷 嘷 嘷 嘷 E-50 Video 嘷 嘷 嘷 嘷 嘷 E-50 S-Video 嘷 嘷 嘷 嘷 嘷 E-50 Presentation Timer 嘷 嘷 嘷 嘷 嘷 E-50 Language 嘷 嘷 嘷 嘷 嘷 E-51 On Screen 嘷 嘷 嘷 嘷 嘷 E-51 Background 嘷 嘷 嘷 嘷 嘷 E-51 Startup Scre
Image • Perform this operation while projecting the picture for which the adjustment/setting will be made. • Select the menu name “Image”. See “Menu Operation Method” on Page E-35 for information about performing menu operations. The item name display will differ depending on the input signal. See “List of Item Names Offering Input Selection and Adjustments/Settings” on Page E-40.
Image Fine Picture Adjust this when the picture shows a lack of color fidelity or flickering. Select the “Fine Picture” item name and adjust with the SELECT 왗왘 buttons so that the lack of color fidelity or the flickering disappears. H Position Adjust this when the picture is shifted to the left or right. Select the “H Position” item name and adjust with the SELECT 왗왘 buttons. V Position Adjust this when the picture is shifted up or down.
Color • Do the following operation while displaying the image you want to adjust or set. • Select the menu name “Color”. See “Menu Operation Method” on Page E-35 for information about performing menu operations. The item name display will differ depending on the input signal. See “List of Item Names Offering Input Selection and Adjustments/Settings” on Page E-40. Quick Color Adj. Select the preset color mode. Select the “Quick Color Adj.
Color Color Temp. The screen color is affected by the color of the illumination and other extraneous light. This function adjusts the white, which is the reference color for video equipment, and improves the quality of color reproduction. Adjustment can also be used to enhance skin colors. Select the item name “Color Temp.” and select the setting contents with the SELECT 왗왘 buttons. Low ............ Medium ...... Normal ....... High ............
Color White Balance This function automatically adjusts the black level and the white level of the analog RGB input signal to suit the personal computer. 1 Select the item name [White Balance] and press the ENTER button. The display will change to [Input Black Signal]. 2 The screen background color of the connected personal computer will be set to black. 3. Press the ENTER button. The display will change to [Adjusting Black] and the black level will be adjusted.
View • Perform this operation while projecting the picture for which the adjustment/setting will be made. • Select the menu name “View”. See “Menu Operation Method” on Page E-35 for information about performing menu operations. The item name display will differ depending on the input signal. See “List of Item Names Offering Input Selection and Adjustments/Settings” on Page E-40. Aspect This function sets the horizontal and vertical picture proportions of the input signal.
View Vertical Flip/Horizontal Flip In selecting the method of projecting to the screen, these functions are set when the projector is in a rear screen installation. XD60 XD60 XD60 XD60 “Vertical Flip” Off “Horizontal Flip” On 06D X XD60 “Vertical Flip” On “Horizontal Flip” On 06D X XD60 XD60 “Vertical Flip” Off “Horizontal Flip” Off XD60 Keystone Keystone distortion will occur when the projector and screen are on an angle (in the vertical orientation).
Setup • Select menu name “Setup”. See “Menu Operation Method” on Page E-35 for information about performing menu operations. The item name display will differ depending on the input signal. See “List of Item Names Offering Input Selection and Adjustments/Settings” on Page E-40. Auto Source The Auto Source function automatically detects the input signal when the power supply is switched on and when the input is switched.
Setup Lamp Mode Use this if the picture is projected on a small screen and the picture is too bright or when projecting images in dark rooms. Select the item name “Lamp Mode” and select the setting contents with the SELECT 왗왘 buttons. Low ............ The lamp brightness is set to 80% and the lamp life is extended. (STATUS indicator is green) Normal ....... The lamp brightness is set to 100% and the screen is bright. (STATUS indicator is off) Note: Frequent switching this mode can degrade the lamp.
Option • Select menu name “Option”. See “Menu Operation Method” on Page E-35 for information about performing menu operations. The item name display will differ depending on the input signal. See “List of Item Names Offering Input Selection and Adjustments/Settings” on Page E-40. Language This function sets the language that is displayed on screen in the messages and menu displays. Select item name “Language” and press the ENTER button to open the Language sub menu.
Option Startup Screen This is the selection of whether or not to display the logo screen at startup time. Select item name “Startup Screen” and select the setting contents with the SELECT 왗왘 buttons. Logo ........... Displays the logo. Blank .......... Does not display the logo. Note: When “Logo” is selected at the startup screen, the “PROJECTOR XD60” logo is displayed. Security Lock A password can be registered and the security lock set in order to prevent unauthorized use of the projector.
Info. • Select menu name “Info.”. See “Menu Operation Method” on Page E-35 for information about performing menu operations. The item name display will differ depending on the input signal. See “List of Item Names Offering Input Selection and Adjustments/Settings” on Page E-40. Status This displays information about the equipment. Select item name “Status” and press the ENTER button. There is a change to the status display. Press the CANCEL button to return to the menu.
Info. Resolution / Frequency This function displays the resolution and frequency of the detected input signal. Lamp Timer This displays the lamp timer. This projector has Lamp mode function. The lamp life will differ between Normal mode and Low mode. Lamp Life Use only in Normal mode: approx.1500 hours Use only in Low mode: approx.2000 hours * Lamp life will differ when there has been switching between the modes.
When an Indicator is Lit or Blinking The indicators on the projector’s control panel lit or blink to notify of problems, as described below. An indicator is also used to notify you of the currently set power mode (under normal circumstances). See “Power Cable Connections and Switching the Power On/Off” on page E-21.
Troubleshooting Check the following matters before requesting servicing. Problem Power does not turn on Reference Page Check • Is the power cord plugged into a power outlet? • Is the lamp cover properly mounted? • Is the projector’s temperature high? To protect the projector, the power cannot be turned on when the projector’s temperature is abnormally high.
Cleaning • Be certain to disconnect the power plug from the power outlet before cleaning. • Do not spray or otherwise expose the projector, lens, or screen to volatile substances such as insecticides. Do not leave rubber or vinyl products in contact with the projector for long periods. Doing so could cause them to undergo qualitative changes or the coatings may peel, etc. Cleaning a Soiled Projector Main Unit • Wipe with a lint-free, soft, dry cloth.
Replacing the Lamp Cartridge • The lamp that is used as a light source in the projector has a limited service life. The rated service life of the lamp is about 1500 hours (when used in normal mode only). This could be shortened depending on conditions of use and other factors. Note that lamp life will be extended when the projector is often used in Low mode.
Replacing the Lamp Cartridge Preparations: Turning the projector upside-down on top of a soft cloth, etc., so that it does not get scratched makes it easier to replace the lamp cartridge. Turn the projector right-side up after replacing the lamp cartridge. 1 Unplug the power cord. 2 Turn the projector upside-down. 3 Remove the lamp cover. (1) Turn the lamp cover’s set screw counterclockwise and loosen until the screw turns freely. (The screw does not come off.
Replacing the Lamp Cartridge 5 Mount the new lamp cartridge. (1) Place the lamp cartridge with its socket facing to the right and push it in slowly. (Line it up with the screw holes in the projector.) (2) Turn the two lamp cartridge screws clockwise to tighten them. 6 Mount the lamp cover. (1) Set the tip of the lamp cover in place, then close the lamp cover. (2) Turn the lamp cover’s screw clockwise to tighten it. 7 Reset the Lamp Timer. Connect the power cable, switch on the power, and then reset.
Specifications Model XD60U Optical Method of projection : DMD Lamp Projection lens : Image size Light Output Contrast Ratio DLP™ (single chip DMD) 0.7 inches 1024⳯768 dots 170 W high pressure mercury lamp Manual zoom (⳯1.2), Manual focus F = 2.6 – 2.9, f = 27.5 – 33.0 mm Minimum 26 inch (at projection distance of 1.20 m / 3.9 feet telephoto) Maximum 300 inch (at projection distance of 11.81 m / 38.
Table of Supported Frequencies The projector automatically identifies the signal input from the computer and selects the optimum resolution as shown on the table below. Manual adjustments may be required for some input signals. See “Picture Adj. / Fine Picture / H Position / V Position” on page E42, 43.
Cabinet Dimensions QUICK MENU MENU AUTO SOURCE STANDBY 242 (9.5) STATUS 53 (2.1) 190 (7.5) 12 (0.
MITSUBISHI ELECTRIC CORPORATION 1 Zusho Baba, Nagaokakyo-City, Kyoto Japan