Installation Sheet
Table Of Contents
- ,H326804,H326806,H326808,
- GENERAL
- INSTALLATION
- STEP 1. Thread the wire through stems and twist tightly onto body. Keep adding additional stems required.
- STEP 2. Slide in the canopy to the stem. And thread the swivel into the top end of the stem set.
- STEP 3. Pull the wires out from the outlet box, and install mounting plate onto the outlet box using the (2) mounting screws. Strip the fixture wires ½” long at the ends.
- STEP 4. Trim excess wire to min 6” beyond stem, strip to 5/8” and twist.
- STEP 5. Fasten bare ground wire to ground wire from the wall outlet box (usually green or copper color) or connect ground wire to green screw on the mounting plate.
- STEP 6. Connect the neutral (white) fixture wire coming from the fixture base to neutral (usually white) outlet wire. Fasten both wires together with a plastic wire nut and tightly wrap the wire nut with electrical tape.
- STEP 7. Repeat the previous step with the hot (black wires). Make sure there are no exposed wires or strands that could cause a dangerous short circuit.
- FAILURE TO CONNECT THE APPROPRIATE WIRES CORRECTLY COULD RESULT IN SERIOUS INJURY OR DEATH!
- STEP 8. Carefully place connections back into the outlet box.
- STEP 9. Mount the canopy to the mounting plate and secure with mounting nuts.
- STEP 10. Install the lamps. H326804 is rated for 60 watt type T lamp. H326806 H326808 is rated for 75 watt type T lamp. DO NOT EXCEED RECOMMENDED WATTAGE!
- STEP 11. Attach the glass on the arm use the washers and ball nuts.
- STEP 12. Restore power to the circuit at breaker or fuse box.
- DIMMING
- CLEANING
- ASSEMBLY AND MOUNTING DIAGRAM
- WIRE NUT/TAPING DIAGRAM
- H326804 B55
- GENERALITÉ
- INSTALLATION
- PAS 6. Relier le fil neutre (blanc) venant de la base du dispositif au fil neutre (généralement blanc) de la boîte de dérivation. Relier les deux fils entre eux à l’aide d’une borne de raccordement en plastique et envelopper celle-ci de ruban isolant ...
- RÈGLAGE D’INTENSITÉ
- NETTOYAGE
- SCHÉMA D’ASSEMBLAGE ET DE MONTAGE
- SCHÉMA DE BORNE DE RACCORDEMENT ET D’ENVELOPPAGE AVEC RUBAN ISOLANT
H326804, H326806, H326808 ARIEL CHANDELIER
www.hudsonvalleylighting.com/mitzi| #mymitzi
ASSEMBLY AND MOUNTING INSTRUCTIONS
GENERAL
•
WARNING-DISCONNECT POWER BEFORE RELAMPING OR
WIRING THE FIXTURE. TURN OFF THE ENTIRE ELECTRICAL
CIRCUIT TO WHICH THE LIGHTING FIXTURE IS ATTACHED
•
INSTALLATION AND MAINTENANCE OF THIS FIXTURE
SHOULD BE COMPLETED BY A LICENSED ELECTRICAN
•
FAILURE TO INSTALL FIXTURE CORRECTLY COULD RESULT IN
SERIOUS INJURY OR DEATH
•
READ ALL INSTRUCTIONS BEFORE STARTING INSTALLATION.
•
IF AN EXISTING FIXTURE IS BEING REPLACED, REMOVE IT AND
NOTE TO WHICH WIRE IN THE OUTLET BOX THE ORIGINAL
FIXTURE WAS ATTACHED.
•
BEFORE DISCARDING THE CARTON DOUBLE CHECK THE
PACKAGING TO MAKE SURE ALL PARTS HAVE BEEN FOUND.
•
THIS FIXTURE WAS DESIGNED TO BE MOUNTED TO AN
OCTAGON OUTLET BOX. THE BOX MUST BE SECURELY
MOUNTED TO THE STRUCTURE OF THE BUILDING.
INSTALLATION
STEP 1. Thread the wire through stems and twist tightly onto
body. Keep adding additional stems required.
STEP 2. Slide in the canopy to the stem. And thread the swivel
into the top end of the stem set.
STEP 3. Pull the wires out from the outlet box, and install
mounting plate onto the outlet box using the (2)
mounting screws. Strip the fixture wires ½” long at the
ends.
STEP 4. Trim excess wire to min 6” beyond stem, strip to 5/8” and
twist.
STEP 5. Fasten bare ground wire to ground wire from the wall
outlet box (usually green or copper color) or connect
ground wire to green screw on the mounting plate.
STEP 6. Connect the neutral (white) fixture wire coming from the
fixture base to neutral (usually white) outlet wire. Fasten
both wires together with a plastic wire nut and tightly
wrap the wire nut with electrical tape.
STEP 7. Repeat the previous step with the hot (black wires). Make
sure there are no exposed wires or strands that could
cause a dangerous short circuit.
FAILURE TO CONNECT THE APPROPRIATE WIRES
CORRECTLY COULD RESULT IN SERIOUS INJURY OR
DEATH!
STEP 8. Carefully place connections back into the outlet box.
STEP 9. Mount the canopy to the mounting plate and secure with
mounting nuts.
STEP 10. Install the lamps. H326804 is rated for 60 watt type T
lamp. H326806 H326808 is rated for 75 watt type T lamp.
DO NOT EXCEED RECOMMENDED WATTAGE!
STEP 11. Attach the glass on the arm use the washers and ball nuts.
STEP 12. Restore power to the circuit at breaker or fuse box.
DIMMING
The fixture can be controlled by a wall dimming device. Only use
triac/electronic dimmer. Make sure carton is marked for use with LED
compact fluorescent-incandescent light source only. These can be
provided by your local electrical distributor, home center, or
hardware store.
CLEANING
Please clean with a soft, dry cloth ONLY! Do not use cleaning products.