MOCET IG7600 Smart Telephone System Administration Manual
IG7600 Administration Manual Environment The equipment you have purchased must not be disposed of with household waste. You should return these to your distributor if they are to replace or dispose of them in an approved recycling centre. FCC Statement This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions in this manual, may cause interference to radio communications.
IG7600 Administration Manual WARNING! 1. Read these installation instructions carefully before connecting the equipment to its power adapter. 2. To reduce the risk of electric shock, do not remove the cover from the equipment or attempt to dismantle it. Opening or removing covers may expose you to dangerous voltage levels. Equally, incorrect reassembly could cause electric shock on re-use of the appliance. 3. Do not expose the equipment to fire, direct sunlight or excessive heat. 4.
IG7600 Administration Manual Table Of Contents 1. 2. 3. 4. Introduction ...................................................................................................................................................... 1 Getting to Know the IG7600 .......................................................................................................................... 3 2.1 Front Panel....................................................................................................................
IG7600 Administration Manual 5. 6. 4.10 Call Park / Call Park Answer ........................................................................................................ 28 4.11 Call Pickup – Individual ............................................................................................................... 29 4.12 Call Waiting .................................................................................................................................. 29 4.13 Caller Blocking ..............
IG7600 Administration Manual 6.5.1 Basic ............................................................................................................................................... 60 6.5.2 Security ........................................................................................................................................... 62 6.5.3 MAC Filter...................................................................................................................................... 64 6.5.
IG7600 Administration Manual 1. Introduction MOCET IG7600 Smart Telephone System is the ultimate SME solution which has rich feature set of IP PBX telephone systems and IP networking systems. It has business essential PBX features such as an auto-attendant, voice mail, multi- line appearances, three way call conferencing, intercom, music on hold, call-forwarding and much more.
IG7600 Administration Manual 1.1 Interfaces WAN Interface: one 10/100/1000 Base-T Ethernet port LAN Interface: one 10/100 Base-T Ethernent port CO Interface: 4 FXO (Loop Start, for PSTN) Analog Device Interface: 1 FXS (for analog Telephone or FAX) Built-in 802.11b/g/n WiFi access point Auto-Pairing button 1.2 Terminals 1 Analog Terminal (Analog Telephone or FAX) 49 IP Stations (IP-Phone; Max. 16 M54 App for iPhone/ Android Phone) 1.
IG7600 Administration Manual 2. Getting to Know the IG7600 2.1 Front Panel The front panel contains several LEDs that indicate the status of the IG7600. Figure 2-1.
IG7600 Administration Manual 2.2 Rear Panel The rear panel contains the ports for the IG7600's data and power connections. Figure 2-2. Rear Panel of IG7600 Label Function WAN RJ-45 connector: Connects the device to your cable modem, or to your ADSL Modem. It’s to connect to the remote network. LAN RJ-45 connector: Connects the device to your PC's Ethernet port, or to the uplink port on your LAN's hub. Line (1-4) RJ-11 connector: Connects the device to your PSTN lines.
IG7600 Administration Manual 3. IG7600 Voice General Features 3.1 3-Way Conference IG7600 supports 3-way conference. Conference allows multiple speakers to participate in a joint telephone conversation. Each participant in a conference can speak and hear the other participants. IG7600 supports one conference room with at most 3 participants. The voice is mixed on IG7600. PS：IG7600 supports this function only when it is a new hardware version IG. 3.
IG7600 Administration Manual simultaneous calls with following functions. • Auto Attendant Functions The Auto Attendant provides an incoming caller with a customized welcome greeting and specific prompts that will describe the options available to the caller. Play the welcome greeting messages depending on the system service mode: Working, Holiday, and Temporary. In Working Service mode, play the welcome greeting messages depending on the system service time: Day, Night, Noon, and Holiday.
IG7600 Administration Manual Each message can be saved for 1 - 30 days or permanently. Support 50 Virtual Mailboxes Enter voicemail through another phone extension • Management Menu Change the Greeting Mode: Working, Holiday, and Temporary. Record the Greeting Messages Record other voice prompts. • Voice Messages Provide two languages service for the all voice files. Support G711-ulaw, G711-alaw, G729 three voice files. Administrators can record the all voice messages by themselves.
IG7600 Administration Manual 3.8 Call By Name IG supports Call by Name now, but it is not enabled as default. We should activate it manually before we use it. Get ready for dial by name process: 1st find the web page Voice-> Voice Mail->General->Auto Attendant->Dial by Name Code and We input a number ( for example “9“) here to use it as a dial by name code. 2nd configure extension user name, for example “Sam Hsu” for extension 205, in Voice->Voice Mail->Phone Extension page as below.
IG7600 Administration Manual input your password (default “0000”) press “5” Record your name and press “#” key, for example saying “Sam Hsu” and then press “#” key after the beep tone.
IG7600 Administration Manual 3.9 Call Operator (Call Attendant) IG7600 supports one Primary operator and one Secondary operator. Any extension can be designated as the operator through system configuration. One primary operator may be assigned in the system. When assigned as operator, this extension supports general system functions.
IG7600 Administration Manual of this entry. • Table Type It decides into which table this entry will be added. • Priority It decides which table will be checked first. If Priority is “Allowed”, IG7600 will check Allowed Table first, if any entry is matched IG7600 will search Denied Table then, the call can be made only when there is any matched entry found in Allowed Table and there is no any matched entry found in Denied Table.
IG7600 Administration Manual Since the priority is allowed, we should check the allowed table first. In Allowed table, since 1000000 has 7 digits, you can only dial the number that is between 1000000 and 2000000 with a length not less than 7, and the extension you use must have a COS level higher or equal to “7”.
IG7600 Administration Manual IG7600 also provide Caller ID Generation to the Caller ID equipped Single Line Telephone. 3.14 Class Of Service (COS) IG7600 provides 8 Classes of Service (COS) for assignment of outside line dialing-privileges. Each extension may be assigned one Day-COS and one Night-COS. The Extension COS is primarily used for restriction and control of long distance dialing. COS 0 is the highest priority. COS 7 is the lowest one. 3.
IG7600 Administration Manual 3.18 Direct Inward System Access (DISA) The feature allows you to remotely access IG7600 lines to make the outside calls. The current PSTN/IP lines are all DISA lines. While ringing to Auto Attendant, the outside callers have direct access to extensions, or make an outside call, The out-calling is to dial a pound (“#”) key at the beginning when Auto Attendant plays the greeting message. The call is secured by means of verified passwords against the assigned extension number.
IG7600 Administration Manual 3.24 IP Trunk IG7600 can register up to 12 SIP Uplink Servers. The extensions may make a call to the users of the Uplink Servers, or any user in the world through the Uplink Servers.
IG7600 Administration Manual • • • • • • Paging Group Number UCD Group Number Pickup Group Number System Speed Dial Number Call Park Number Conference Room Number 3.28 PSTN Backup In case of power failure, IG7600 automatically switches the first PSTN line to the Single-line analog phone. The other PSTN lines are not supported 3.29 Registration Server The IG7600 combines Proxy and Registrar servers in its application.
IG7600 Administration Manual 2 IG has a domain name that we can reach, users can set their IP Phones Sip servers to the domain name as below. 3.31 Service Mode IG7600 provide Day and Night settings for each weekday in service mode page. It will be applied in the following function: - Answering Position: Trunk incoming call may be forwarded to different extensions according to the settings. - Class of Service (COS): Phone extension may be assigned to have the different COS in the different time.
IG7600 Administration Manual 3.33 System Speed Dial IG7600 stores frequently dialed numbers. These Speed Dial Numbers are accessed for dialing by the associated Speed Dial Directory Numbers. The Speed Dial Directory Numbers are assigned in Numbering Table. The Speed Dial is only for outgoing calls. IG7600 stores up to 100 Speed Dial Numbers. In the Speed Dial Number, it’s allowed to store Phone number up to 20 digits in length.
IG7600 Administration Manual Basically in one IGW Group we demand one of the IGs works under master mode, others work under slave mode. The members in the group need to be found by each other on the internet make sure about it before you use this function. When an IGW Group is build up successfully we can choose IGW Group as a Call Routing way in Call Routing configuration page.
IG7600 Administration Manual Entity-2 Entity-1 IG-A Internet IG-B Entity-1 Initiator: Entity-1 is an IPP Initiator: Entity-1 is a SMP Entity-5 Entity-4 Entity-3 IG-A Entity-1 Entity-1, Entity-2 Entity-1, Entity-2 Entity-1 IG-C IG-B Entity-3 Entity-3 IG-C Entity-3 Entity-3, Entity-4 Entity-3 Entity-5 Entity-3 Entity-5 Entity-3 Entity-5 Entity-6 Operation Entity-1 call/hold/retrieve Entity-3 Entity-1 transfer/forward Entity-2 to Entity-3 Entity-1 transfer/forward Entity-3 to Entity-2 Entit
IG7600 Administration Manual With this setting IG A’s Ext 299 can transfer a call from 201 to IG B’s Ext 101 by dialing 101 directly. Get Ready [IG7600 programming—IGW Group] IGW Name: The name of IG. It will be referred for the other IGs. Run Mode: The mode that IG is running. IG can run in Master Mode or Slave Mode. Master Mode: When IG is running in master mode, it maintains an IG list table.
IG7600 Administration Manual [IG7600 programming—Call Routing Rule] To fulfill the condition of the Sample, IG A has one Call routing rule to IGW Group member -- IG B whose settings are like this figure shows: when the dialing is from 101 to 199 and is exactly a 3 digit number, IG A Transfer the dialing to IG B directly without deleting any of the digit. Steps a) b) c) d) e) Access IG B from IG A’s Ext Off-hook the phone 201 and dial 299. Pickup FXS 299 to answer the call.
IG7600 Administration Manual IG7600 Voice Extension Features Daylight Saving Time Default Set Direct In Dialing (DID) Direct Inward System Access (DISA) Emergency Call Extension Password Fax/Modem Flash – Analog Port (SLT) Flash Recognition IP Trunk Message Waiting Indication (MWI) Music on Hold Numbering Plan PSTN Backup Registration Server Service Mode Station Message Detailed Recording (SMDR) System Speed Dial System Time & Date Trunk Group UCD (Uniform Call Distribution) Group (or Hunt Group) Wizard S
IG7600 Administration Manual Phone Book Phone Lock/Unlock Plug & Play Reminder Tone Service Mode Switching Transfer / Recall Volume Control Web Management No No NA NA NA Yes Yes NA 3.38 Wizard Setup The IG7600 has a setup Wizard that provides the system administrator with a series of step-by-step operations. You can get in the wizard process from the entry shown on the main page. When you start setup wizard you can configure the corresponding settings step by step. The following four items are supported.
IG7600 Administration Manual 4. IG7600 Voice Extension Features IG7600 follows SIP standard to serve SIP phones. Basically, telephone features that meets SIP standard can be applied in IG7600. Smart Phone M54(-i) , M22, M62 and IP2061 phone support many phone features. But for adding some traditional KTS features that are not defined definitely in SIP protocol, some specified information are transmitted between IG7600 and IP2061/M22/M62/M54(-i) Phones.
IG7600 Administration Manual Page (All/Group) - Paged Page Answer Page Allow / Deny Phone Book Phone Lock/Unlock Plug and Play Reminder Tone Service Mode Switching Transfer Web Management Volume Control Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No No No No Yes Yes Yes Yes Yes No Depends No No No Yes Yes Yes No No Yes No Yes No No No Depends No No Depends No Depends Depends Depends NOTE: the word “Depends” means that the features depend on whether the phon
IG7600 Administration Manual 4.5 Auto Hold You may enable the feature to simplify call handling and avoid accidental “lost” calls. Hold will automatically place any call that is currently connected at your phone on hold whenever a Trunk line button is pressed. 4.6 Call Fork IG7600 supports to ring another extension or an outside destination via IP Trunk simultaneously when the extension gets an incoming call.
IG7600 Administration Manual *24 + Type + * + (PSWD) + * + Outside Number To disable, dial **24. Follow Me Call Forward: Forwards calls at your extension to the extension where you are currently working. To enable, dial *25 + Type + Ext No + * + Password To disable, dial **25 + Ext No + * + Password These Call Forward features can also be set / cancelled in web page of IP2061/M22/M62. 4.8 Call Hold Trunk and Intercom calls can be placed on hold at any extension.
IG7600 Administration Manual by inputting the Trunk Access Code 701. Meanwhile, other extensions can also pick up this trunk call by pressing the IDLE Individual Call Park key and input the extension number “101”. 4.11 Call Pickup – Individual You may answer the calls at another specified extension. The feature allows you to easily access calls ringing via the feature access code. *53 + Extension Number 4.
IG7600 Administration Manual 4.17 Do Not Disturb (DND) Extension users can enable DND to reject all incoming calls. The DND on an extension can be allowed or denied through the feature access code. To enable the Do Not Disturb feature, dial *4. To disable the Do Not Disturb feature, dial **4. DND and FWD can be set independently. If multiple features are set at the same time, it is applied in the order of Direct FWD > DND > Busy/No Answer FWD. 4.
IG7600 Administration Manual Paging Accept Default Feature Key Setting Phone Lock disabled Call Forward (Direct, Busy, No Answer, DND, Call Fork) disabled DND disabled Agent Log on Auto Answer disabled Distribution List clean To activate the Default Setting feature, dial *69+ (Extension Password or Administrator Password). 4.22 Hold Reminder IP2061/M22/M62 provides a programmable timer to remind you that a call has been left on Hold.
IG7600 Administration Manual Wink Flash Lit – – the line is held recall the line is in talk 4.26 Mute The Mute feature allows the user to disable the handset transmitter or the speakerphone microphone. 4.27 On Hook Dialing IP2061/M22/M62 phone extensions may make outgoing calls without lifting the handset and monitor the dialing status through the built-in speaker. The button lamp is lit when dialing. 4.
IG7600 Administration Manual 4.32 Plug & Play While connecting IP2061/M22/M62 to IG7600’s LAN port, it will register to IG7600 automatically. IG7600 will also assign a valid extension number to the phone directly. When IP2061/M22/M62 and IG7600 connect to the same Router, IG7600 will assign a valid extension number to the IP2061/M22/M62 also. IG7600 will do Plug & Play with M54(-i) only when the pairing button is pushed. 4.
IG7600 Administration Manual 4.37 Web Management The IP2061/M22/M62 is supported two-level web management. The Administrator has several pages to configure the IP phone. User is able to configure personal information by himself. User level is not including these two pages – software update, SIP configuration. Copyright 2013 Tecom, Co. LTD.
IG7600 Administration Manual 5. Quick Installation This Quick Installation helps you to install the product quickly and easily. For detailed instructions on installation, and further setup option, please refer to the configuration chapter. 5.1 Connecting the IG7600 (1) Place IG7600 in an optimum location. (2) Connect the included Category 5 Ethernet network cable to the IG7600’s LAN port or WAN port. Then connect the other end of the network cable to a switch or hub or directly your PC’s Ethernet port.
IG7600 Administration Manual Figure 5-1. Wan Settings (Static IP mode) The Dynamic Host Configuration Protocol (DHCP) is an Internet protocol for automating the configuration of computers that use TCP/IP. DHCP can be used to automatically assign IP addresses, to deliver TCP/IP stack configuration parameters such as the subnet mask and default router, and to provide other configuration information. This page shows the current existing WAN interface in this system is DHCP mode (Figure 5-2). Figure 5-2.
IG7600 Administration Manual Figure 5-3. Wan Settings (PPPoE mode) 5.2.2 Secondary WAN Setting IG7600 supports secondary WAN which is dedicated for IP Trunk. If you check “Enable Secondary WAN” then it will turn LAN port into secondary WAN port. And you still can use wireless interface for LAN access. Regarding secondary WAN settings, please refer to 5.2.1 WAN settings. 5.2.3 LAN Setting This page (Figure 5-4) allows you giving LAN IP and Subnet Mask for LAN interface.
IG7600 Administration Manual Figure 5-4. LAN Settings 5.2.4 Wireless Basic The page (Figure 5-5) allows you to configure basic feature of the wireless LAN interface. You can enable or disable the wireless LAN interface, hide the network from active scanning, set the wireless network name (also known as SSID), and restrict the channel set based on country requirement. Figure 5-5. Wireless Basic 5.2.
IG7600 Administration Manual Figure 5-6. Internet Time – Automatic 5.2.6 Wizard Setup Finished When you click “Save & Reboot” Button at above page, the wizard setup will save your setting and the wizard setup will be finished. Then the system will reboot as shown below.(Figure 5-7) Figure 5-7. Wizard Setup finished Congratulations! The wizard setup of the IG7600 is complete. For additional details, advanced configuration, or any other questions, refers to the next chapter. Copyright 2013 Tecom, Co.
IG7600 Administration Manual 6. Configuration 6.1 Setup Connect the IG7600 to PC. The default LAN IP of the IG7600 is 192.168.123.1. The default WAN IP of the IG7600 depends on upper router’s DHCP server. For web login, the default user name is “admin1234”; the default password is “adminxxxxxx”. (”xxxxxx” are the last 6 characters of IG’s MAC Address.) For telnet login, the name/password is the same as web login. 6.
IG7600 Administration Manual Management Diagnostics Logout Figure 6-2. Device Info - Summery Copyright 2013 Tecom, Co. LTD.
IG7600 Administration Manual 6.3 Device Info This information reflects the current Status of IG7600 connection. It includes the following topics: Summary Statistics Route ARP DHCP 6.3.1 Summary In the page (Figure 6-2) you can get the information reflects the current software version and connection status. It includes Device Info, Network Info and Date/Time.
IG7600 Administration Manual Figure 6-4. Device Info – Statistics – WAN 6.3.3 Route In this page you can get the IP route information of the device. (Figure 6-5) Figure 6-5. Device Info – Route 6.3.4 ARP This page shows an ARP table which maps IP network addresses to hardware addresses used by data link level protocol. (Figure 6-6) Copyright 2013 Tecom, Co. LTD.
IG7600 Administration Manual Figure 6-6. Device Info – ARP 6.3.5 DHCP This page shows a DHCP Leases table which shows the all used IP addresses under IG7600’s DHCP Server. (Figure 6-7) Figure 6-7. Device Info – DHCP Copyright 2013 Tecom, Co. LTD.
IG7600 Administration Manual 6.4 Advanced Setup Advanced Setup allows system administrator to configure the following topics: WAN LAN NAT - Virtual Servers - Port Triggering - DMZ Host Security - IP Filtering Outgoing Incoming Parental Control - Time Restriction - URL Filter Quality of Service - DSCP Marking - Bandwidth Control Routing - Static Route Dynamic DNS Upnp 6.4.1 WAN There are three modes that you can give WAN IP address to IG7600: Static IP mode, DHCP mode and PPPoE mode.
IG7600 Administration Manual The Dynamic Host Configuration Protocol (DHCP) is an Internet protocol for automating the configuration of computers that use TCP/IP. DHCP can be used to automatically assign IP addresses, to deliver TCP/IP stack configuration parameters such as the subnet mask and default router, and to provide other configuration information. This page shows the setting of WAN interface which is DHCP mode (Figure 6-9). Figure 6-9.
IG7600 Administration Manual 6.4.2 Secondary WAN IG7600 supports secondary WAN which is dedicated for IP Trunk. If you check “Enable Secondary WAN” then it will turn LAN port into secondary WAN port. And you still can use wireless interface for LAN access. Regarding secondary WAN settings, please refer to 6.4.1 WAN settings. 6.4.3 LAN It allows you to set LAN IP and Subnet Mask for LAN interface. A DSP IP address can be configured for FXO/FXS application.
IG7600 Administration Manual Figure 6-11. Advanced – LAN 6.4.4 NAT It’s separated into three parts: Virtual Servers, Port Triggering, and DMZ Host. 6.4.4.1 Virtual Servers Virtual Server allows you to direct incoming traffic from WAN side identified by Protocol and External port to the internal server with private IP address on the LAN side. The “Internal Port” can be modified if the “External Port” needs to be converted to a different port number used by the server on the LAN side.
IG7600 Administration Manual Figure 6-12. Advanced – NAT – Virtual Servers Figure 6-13. Advanced – NAT – Virtual Servers – Add 6.4.4.2 Port Triggering Some applications require that specific ports in the IG7600's firewall opened for access by the remote parties. Port Triggering dynamically opens up the "Open Ports" in the firewall when an application on the LAN initiates a TCP/UDP connection to a remote party using the "Trigger Ports".
IG7600 Administration Manual Figure 6-14. Advanced – NAT – Port Triggering Figure 6-15. Advanced – NAT – Port Triggering – Add 6.4.4.3 DMZ Host IG7600 will forward IP packets that do not belong to any of the applications configured in the Virtual Servers table to the DMZ host computer. Enter the computer's IP address and click "Save Settings" to activate the DMZ host. Clear the IP address field and click "Save Settings" to deactivate the DMZ host. (Figure 6-16) Copyright 2013 Tecom, Co. LTD.
IG7600 Administration Manual Figure 6-16. Advanced – NAT – DMZ 6.4.5 Security It supports IP Filtering Setup. It’s separated into two parts: Outgoing and Incoming. 6.4.5.1 IP Filtering - Outgoing It allows the administrator to create a filter rule to identify outgoing IP traffic by specifying a new filter name. At least one condition is needed. All of the specified conditions in this filter rule must be satisfied for the rule to take effect. (Figure 6-17,Figure 6-18) Figure 6-17.
IG7600 Administration Manual Figure 6-18. Advanced – Security – IP Filtering – Outgoing – Add 6.4.5.2 IP Filtering - Incoming It allows the administrator to create a filter rule to identify incoming IP traffic by specifying a new filter name. At least one condition is needed. All of the specified conditions in this filter rule must be satisfied for the rule to take effect.
IG7600 Administration Manual Figure 6-20. Advanced – Security – IP Filtering – Incoming – Add 6.4.6 Parental Control It’s separated into two parts: Time Restriction, and URL Filter. 6.4.6.1 Time Restriction The administrator can add time restriction to a special LAN device connected to IG7600. The “Browser's MAC Address” automatically displays the MAC address of the LAN device where the browser is running.
IG7600 Administration Manual Figure 6-22. Advanced – Parental Control – Time Restriction – Add 6.4.6.1 URL Filter The administrator can add 100 entries maximum to include/exclude the URL address and Port number. Choose “Include” means the user can only connect to the URL that you add. Choose “Exclude” means the user cannot connect to the URL that you add. “Include” and “Exclude” are exclusive. The all entries are for the selected type. (Figure 6-23, Figure 6-24). Figure 6-23.
IG7600 Administration Manual Figure 6-24. Advanced – Parental Control – URL Filter – Add 6.4.7 Quality of Service It’s separated into two parts: DSCP Marking, and Bandwidth Control 6.4.7.1 DSCP Marking IP QoS is applied to the traffic from LAN to WAN; the traffic from WAN to LAN will not be applied. (Figure 6-25) If "Enable DSCP Mark” checkbox is selected, choose a default DSCP mark to automatically mark incoming traffic without reference to a particular classifier.
IG7600 Administration Manual all voice packets have been queued in the highest IP packets, and the others have been queued in the normal IP packets if they have not been set in the traffic class rule. Figure 6-26. Advanced – Quality of Service – Bandwidth Control 6.4.8 Routing 6.4.8.1 Static Route The Static Route allows you to add special routing rules into routing table. Figure 6-27. Advanced – Route – Static Route Click “Add” to create a new Static Route.
IG7600 Administration Manual Figure 6-28. Advanced – Route – Static Route – Add 6.4.9 Dynamic DNS The Dynamic DNS service allows you to alias a register domain name to a dynamic IP address. It allows IG7600 to be more easily accessed from various locations on the Internet. Click “Add” or “Remove” to configure Dynamic DNS. (Figure 6-29) Figure 6-29. Advanced – Dynamic DNS Now IG7600 support for three DDNS provider, DynDNS.org and TZO and custom provider.
IG7600 Administration Manual Figure 6-30. Advanced – Dynamic DNS – DynDNS.org Figure 6-31. Advanced – Dynamic DNS – TZO Copyright 2013 Tecom, Co. LTD.
IG7600 Administration Manual Figure 6-32. Advanced – Dynamic DNS – Customer-Provider 6.4.10 Upnp It’s used to enable or disable the universal plug and play function. (Figure 6-33) Figure 6-33. Advanced – Upnp 6.5 Wireless Use the Wireless screen to configure the IG7600 for wireless access. It is separated into 7 parts: Basic - Primary - Additional Copyright 2013 Tecom, Co. LTD.
IG7600 Administration Manual Security MAC Filter Wireless Bridge Advanced Station Info Power Saving The configurable items for each part would be described in the following. 6.5.1 Basic It’s separated into two parts: Primary, and Additional. 6.5.1.1 Primary This page allows you to configure the basic features of the wireless LAN interface.
IG7600 Administration Manual Figure 6-35. Wireless – Basic – Additional Copyright 2013 Tecom, Co. LTD.
IG7600 Administration Manual 6.5.2 Security This page allows you to configure security features of the wireless LAN interface. It allows you to select your Security Mode: Manual and WPS. In WPS mode, it follows the Wi-Fi Protected Setup standard for easy and secure wireless network set up and connection. User can use Push-Button or PIN to configure the connection with IG7600. In Push-Button method, IG7600 and client must press the WPS button to establish connection.
IG7600 Administration Manual Figure 6-37. Wireless – Security – 1 Figure 6-38. Wireless – Security – 2 WEP Encryption: Selecting Disabled disables WEP data encryption. Selecting Enabled enables WEP data encryption and requires that a valid network key be set and selected unless 802.1X is enabled. WEP, short for Wired Equivalent Privacy, is a protocol for wireless LANs or local area networks. This WEP is defined in the 802.11 Standard.
IG7600 Administration Manual physical layer. WEP is designed to make up for the inherent security in wireless transmission as compared to wired transmission. Network Key: Set whether shared key authentication is required to associate. A valid network key must be set and selected if required. 6.5.3 MAC Filter Figure 6-39. Wireless – MAC Filter This page allows users to Add/Remove hosts with the specified MAC addresses that are able or unable to access the wireless network.
IG7600 Administration Manual 6.5.4 Wireless Bridge This page allows you to configure wireless bridge features of the wireless LAN interface. You can select Wireless Bridge (also known as Wireless Distribution System) to connect to other wireless bridge device, but the access point functionality will be disabled. Selecting Access Point enables access point functionality. Wireless bridge functionality will still be available and wireless stations will be able to associate to the AP.
IG7600 Administration Manual Control Sideband: Specify if the extension channel should be in the “Upper” or “Lower” sideband. 802.11n Rate: Set the Physical Layer rate. These rates are only applicable when the”802.11n/EWC” is configured as “Auto”. 802.11n Protection: In “Auto” mode, the wireless devices use RTS/CTS to improve 802.11n performance in mixed 802.11g/802.11b networks. Turn protection off to maximize 802.11n throughput under most conditions. Do not disable 802.
IG7600 Administration Manual Figure 6-42. Wireless – Advanced RTS Threshold: This value should remain at its default setting of 2347. The range is 0~2347 bytes. Should you encounter inconsistent data flow, only minor modifications are recommended. If a network packet is smaller than the packet RTS threshold size, the RTS/CTS mechanism will not be enabled. The IAD sends Request of Send (RTS) frames to a particular receiving station and negotiates the sending of a data frame.
IG7600 Administration Manual WMM (Wi-Fi Multimedia): Feature that improves the experience for audio, video and voice applications over a Wi-Fi network. WMM No Acknowledgement: When the “WMM No Acknowledgement" is enabled, the receiver will not acknowledge received packets during wireless packet transmit. It is suitable in the environment where communication quality is good and interference is weak. It can improve transmission efficiency. WMM APSD: WMM Automatic Power Save Delivery.
IG7600 Administration Manual 6.6 Voice Use the Voice screen to configure the IG7600’s voice related parameters.
IG7600 Administration Manual Figure 6-45. Voice – Phone – Phone Extension – 1 Figure 6-46. Voice – Phone – Phone Extension – 2 SIP Authentication: It provides 49 IP phones or Smart phones to register. Phone Number: The phone number is a station number. If it conflicts with the setting in Numbering Plan, it fails to add or make the change. Its value range is limited by Start Extension Number and End Extension Number settings in Numbering Plan page. Password: The user password of this phone.
IG7600 Administration Manual If Mac binding exists, only the extension with this Mac address will be accepted to be registered. Allow Open Door: This field is for user to configure if the extension is allowed to open door. Day COS: The field assigns Class of Service for day mode operation. Acceptable values are 0-7. At default, all extensions are unrestricted. Night COS: The field assigns Class of Service for night mode operation. Acceptable values are 0-7. At default, all extensions are unrestricted.
IG7600 Administration Manual Figure 6-47. Voice – Phone – Door Settings Door Phone: Door Phone Numbers. Status: Door Phone Status(Disconnected/Closed/Opened) Start Time/ End Time: During this period Door Phone should turn on its LED light. Open Time: This is the time that door phone delays before open the door when receiving an open door request. Ring Time: When a call is not answered after this time. The ringing will stop automatically.
IG7600 Administration Manual 6.6.1.3 Security Card Registration This page shows the Door Card table, and allows you to configure them.(Figure 6-48) Figure 6-48. Voice – Phone – Door Card When you want to add new door card to this table, you should push the “Start Register” button to start the register process and swipe the card. At most you can add 32 cards. You can change a card’s name and status in the table by pressing the edit button 6.6.1.
IG7600 Administration Manual Auto Hold: When you are using a line and press another key, IG7600 can hold the original line. Select “Enable” to open this function. Copyright 2013 Tecom, Co. LTD.
IG7600 Administration Manual Figure 6-49. Voice – Phone – Programmable keys When there are IP phones registered to IG7600, you can configure their key setting. In Extension List, press “Configure” to configure keys of the specific phone. Follow Gateway Settings: Use default IG7600 key setting for the IP phone. If you check the checkbox, all the input operations are disabled, and the Ext’s programmable keys settings will use the Gateway settings.
IG7600 Administration Manual Copyright 2013 Tecom, Co. LTD.
IG7600 Administration Manual Figure 6-50. Voice – Phone – Extension Linekey-Configure 6.6.2 Trunk Use the Trunk screen to configure the PSTN/IP Trunk function related parameters. It is separated into 7 parts: IP Trunk Trunk DID Trunk Group Answering Position Call Routing Call Restriction Copyright 2013 Tecom, Co. LTD.
IG7600 Administration Manual Emergency Numbers 6.6.2.1 IP Trunk This page allows you to configure the Proxy and Register server of IP Trunks; up to 12 lines of IP Trunk are supported. (Figure 6-51, Figure 6-52) Figure 6-51. Voice – Trunk – IP Trunk – 1 Figure 6-52. Voice – Trunk – IP Trunk – 2 Copyright 2013 Tecom, Co. LTD.
IG7600 Administration Manual Subscriber Information: Phone Number: It’s the assigned phone number from uplink server. Auth ID: The Account ID of registration to uplink server. It’s used for Digest Authentication. Auth Password: The Password of registration to uplink server. It’s used for Digest Authentication. SIP Proxy: The position of uplink SIP proxy server. IP address and domain name are all supported. SIP Proxy Port: The SIP signal port of uplink registrar server.
IG7600 Administration Manual If there is no any dialed number after the setting time, the number will be sent out immediately. Its range is form 2 to 9 seconds. Pause Time: The pause time of alphabet “p” in the process of call dialing Session Timeout: It means the longest communication time for IP trunks, zero means no restriction. RPort: When client is behind a NAT, the rport and received filed can allow SIP proxy to append the public IP address and port of NAT and transfer SIP message correctly.
IG7600 Administration Manual 6.6.2.3 Trunk Group This page allows you to configure the virtual Trunk Group. Up to 4 Trunk Groups are supported. (Figure 6-54, Figure 6-55) Trunk Group & Label Name: This item allows you to assign physical Trunk to virtual Trunk Group. For four PSTN lines and four IP lines you can choose from Group1 to Group 4. PS: There is a special trunk group named Group ALL, all lines are considered to be a member of the group.
IG7600 Administration Manual Figure 6-55. Voice – Trunk – Trunk Group – 2 6.6.2.4 Answering Position Figure 6-56. Voice – Trunk – Answering Positions This page allows you to configure an answering position for each Trunk line's incoming call including PSTN trunk and IP Trunk. You can choose Auto Attendant, Operator, UCD Group or manually configure the target extension phone number on Day/Night basis. (Figure 6-56) Choose Auto Attendant, you can configure an AA Menu number.
IG7600 Administration Manual 6.6.2.5 Call Routing This page allows you to configure the call routing table. A maximum 100 entries are allowed. Each entry is a routing rule for outgoing call. From/To define the number range, Min/Max define the match length, Del/Insert can change the target number, Destination to define the outbound call interface. (Figure 6-57) Figure 6-57. Voice – Trunk – Call Routing Table – 1 6.6.2.6 Call Restriction This page allows you to configure the Call Restriction Table.
IG7600 Administration Manual can be made only when there is any matched entry found in Allowed Table and there is no any matched entry found in Denied Table. If Priority is “Denied”, IG7600 will check Denied Table first, if any entry is matched IG7600 will search Allowed Table then, the call will be forbidden only when there is any matched entry found in Denied Table and there is no any matched entry found in Allowed Table. Figure 6-58. Voice – Trunk – Call Restriction 6.6.2.
IG7600 Administration Manual 6.6.3 System Use the System screen to configure the System function related parameters. It is separated into five parts: Numbering Plan Service Mode Transmission SMDR UCD Call Log 6.6.3.1 Numbering Plan Figure 6-60. Voice – System – Numbering Plan This page allows you to configure extension number range. You can also define some special service numbers in the table. (Figure 6-60) Start extension: It’s the start phone number of system internal extension.
IG7600 Administration Manual Figure 6-61. Voice – System – Numbering Plan – Operator Configuration Operator day: It’s the system operator number during day. If dial Operator speed-dial number, this extension will be called during day. Operator Night: It’s the system operator number during night. If dial Operator speed-dial number, this extension will be called during night.
IG7600 Administration Manual Start Paging Group number: 3 paging groups are defined in IG7600. If dialing a Paging Group number, the call will page to predefined internal IP phones. It can also select the Range like All Paging Number. The maximum phones for each paging group are 49. While pressing “Configuration” in “Start Paging Group number”, it shows Paging Group Configuration screen. (Figure 6-62) Figure 6-62.
IG7600 Administration Manual For other items, if “Timer Enable” is YES, the incoming call will be transferred to another UCD Group’s member every “No Answer Time”. If NO, the call will ignore “No Answer Time” and finally reroute to “Reroute Destination” after “Reroute Time”. “Reroute Destination” can be an Auto Attendant Menu, an extension, a virtual extension, or phone extension’s mailbox. “UCD Group Name” is shown on the phone when receiving the UCD Group call.
IG7600 Administration Manual Figure 6-65. Voice – System – Service Mode Figure 6-66. Voice – System – Service Mode 6.6.3.3 Transmission This page allows you to configure the Audio, FXS, and FXO settings. Click “Save Settings” button to save the new configuration. (Figure 6-67) Copyright 2013 Tecom, Co. LTD.
IG7600 Administration Manual Copyright 2013 Tecom, Co. LTD.
IG7600 Administration Manual Figure 6-67. Voice – System – Transmission Audio: It is used to set many Audio-related options. It will be applied to the all FXS and PSTN lines. Country: It may be used to determine not only the Caller ID detection/transmission method but also ring/tone cadence/frequency. RTP Packet Size: 10/20/30/40/50/60 ms. Codec G.711 u-law, G.711 a-law and G.729: IG7600 supports different audio priority. You can choose “None”, “First”, “Second” and “Third”.
IG7600 Administration Manual Call ID Method: The system provides the ability to detect the calling party identification provided by PSTN lines. It also transmits the calling party identification to POTS ports. There are four choices: NONE, DTMF Before Ring, DTMF After Ring, FSK Before Ring, and FSK After Ring. Inter-digit Timeout: Its range is from 2 to 9 seconds. FXS Hotline: Enable/Disable FXS Hotline Number: FXS dialing number in Hotline application.
IG7600 Administration Manual Ring Abandon Time: It specifies the maximum time between valid ring signals from the CO/PBX. If the duration between rings exceed the Ring Abandon time, IG7600 stops ringing the destination(s) and the port returns to idle. The timer range is 1 to 10 seconds on 1 second increments. Release Guard Time: The guard time to ignore the noise signal when releasing the call. The timer range is 1.0 to 3.0 seconds on 0.5 second increments.
IG7600 Administration Manual Figure 6-69. Voice – System –SMDR – View SMDR The “PSTN Outgoing Call Duration Start Time” is used to estimate whether the PSTN outgoing call to be recorded. If the duration is less than it, the call won't be recorded. If log mode is configured, the specified SMDR record will be sent to local or/and remote log server. Figure 6-70. Voice – System –SMDR Configuration 6.6.3.5 UCD Call Log This page shows the Call Log for incoming call to UCD group.
IG7600 Administration Manual Figure 6-71. Voice – System – UCD Call Log 6.6.4 Voice Mail IG7600 provides a built-in Auto Attendant and Voice Mail System. It is separated into 7 parts: General Phone Extension Virtual Extension Update MOH File Update Voice File Holiday Advanced The configurable items for each part would be described in the following. 6.6.4.1 General This page allows you to configure the general settings of the auto attendant and voice mail.
IG7600 Administration Manual VAA Codec: Choose the codec of auto attendant. RTP Packet Size: Choose the RTP packet size of auto attendant. DISA: Enable/Disable DISA. When enable DISA, Auto Attendant plays the Greeting message and the Caller dials “#” key, caller can make an outside call. When disable DISA, caller can’t make an outside call. Dial by Name Code: This code is used as an entry code of Dial by name function in AA process. It is a disabled function by default.
IG7600 Administration Manual Figure 6-73. Voice – Voice Mail – General – Single Digit Table Figure 6-74. Voice – Voice Mail – General – 2 Voice Mail: (Figure 6-74), Days for Keeping Voice Mail: Keep days for leaving messages. 0 means that the messages are kept until the users delete them. Max recording time: The range of recording time is form 1 to 30 minutes. Silence detection for VM recording: Set “Enable” of this item will do the silence detection in VM recording.
IG7600 Administration Manual SMTP Support SSL: Choose “Yes” to support SSL. SMTP Server: SMTP Mail Server. SMTP Server Port: SMTP Mail Server port. The default value is 25. Sender Email Address: Email Address of Sender. Sender User Name: User Name of Sender’s Email. Sender Password: Password of Sender’s Email. Voicemail Tag: Voicemail tag Email header: Email header Email Test Account: Input a Target Mailbox here. Press the button [Email Test] To send a test Email to the Target Mailbox. 6.6.4.
IG7600 Administration Manual Distribution Lists: This item is used to configure the Distribution Lists of the Ext. You can configure 3 Lists at most. Usage: When you hear your message and you want to transfer the message (Press 4 when listening to the message) to a group of users, you can use Distribution Lists to make this easier. Each list can configure ten EXTs or Virtual Extensions at most to be the destinations.
IG7600 Administration Manual 6.6.4.3 Virtual Extension IG7600 provides 50 Virtual Mailboxes. These Virtual Mailboxes can be used by the members not works in the office, or as a secondary mailbox (Figure 6-78). When selecting “Configuration”, it also has an Extension Configuration page to be configured (Figure 6-79) Figure 6-78. Voice – Voice Mail – Virtual Extension Figure 6-79. Voice – Voice Mail – Virtual Extension Configuration 6.6.4.
IG7600 Administration Manual Figure 6-80. Voice – Voice Mail – Update MOH File 6.6.4.5 Update Voice File The voice files could be uploaded from local PC side. These voice files are compressed in Linux System. It allows a “.tar”, “.tgz” or “.tar.gz” compressed format file. (Figure 6-81) Figure 6-81. Voice – Voice Mail – Update Voice File 6.6.4.6 Holiday This page allows you to configure the holiday or special off-duty days. You can click the buttons under the table to choose pages.
IG7600 Administration Manual Figure 6-82. Voice – Voice Mail – Holiday 6.6.4.7 Advanced This page allows you to browse, upload or download voice files through IG7600’s ftp server. (Figure 6-83) Figure 6-83. Voice – Voice Mail – Advanced 6.6.5 NAT Traversal If IG is put behind a Router, you need to configure this page to enable NAT Traversal. (Figure 6-84, Figure 6-85) Copyright 2013 Tecom, Co. LTD.
IG7600 Administration Manual Figure 6-84. Voice – NAT Traversal – 1 Figure 6-85. Voice – NAT Traversal - 2 The following items will be configured in the NAT Traversal page: NAT Traversal Enable: Enable/Disable. IG can work properly if it’s pub behind NAT only when it’s enabled. STUN Server: A STUN server located at Internet. TURN Server: A TURN server located at Internet. Username: Most TURN server needs username/password to authenticate.
IG7600 Administration Manual Keep alive Interval: Keep alive interval for STUN server. UPNP Port-Mapping Enable: To enable/disable UPNP client. Router Private Address: If you choose “Auto” UPNP client will detect Router’s private IP address by itself. If you choose “Manual” you should input Router’s private IP address manually. Router Public Address: It records Router’s public IP address detected by STUN. External Registration SIP Port: Port that will be opened on Router for SIP port.
IG7600 Administration Manual Note: When do you need this function? If IG has a public IP for remote EXTs to reach there is NO NEED to use NAT Traversal. When IG works under the public network, and has a domain name, there is NO NEED to use NAT Traversal either. Sometimes IG works behind a router, M54 can only reach to IG through the router with the IG’s domain name. We have to tell IG the Router’s external IP Address if we have a static one.
IG7600 Administration Manual 6.6.6.1 Remote Maintenance Figure 6-86. Voice – Remote Maintenance The following items will be configured in the Remote Maintenance page: Remote Maintenance: Enable/Disable. When it’s enabled, IG will write necessary information to maintenance log. Destination Email: If it’s set, maintenance log file will be sent to this Email address automatically if user presses “*64” accordingly.
IG7600 Administration Manual Figure 6-87. Voice – Registered Phone Copyright 2013 Tecom, Co. LTD.
IG7600 Administration Manual 6.7 Management The system administrator can do the following functions to manage the configurations, events, and software update of the IG7600. Settings - Backup - Update - Restore Default TR-069 Client Time Settings - Internet Time - Daylight Saving Time Access Control - Service Port - Services - IP Addresses - Password Open Door Log IP Camera Update Software Upgrade Phone Software Upgrade Door FW APNS Certificate Reboot 6.7.
IG7600 Administration Manual Figure 6-89. Management – Settings – Update 6.7.1.3 Restore Default You can choose restore Voice Files or Default Settings or Restore All in the drop-down menu. Click “Restore” to restore selected default settings. This would be helpful when the voice files or settings are messed up. (Figure 6-90) Figure 6-90. Management – Settings – Restore Default 6.7.
IG7600 Administration Manual Figure 6-91. Management – TR-069 Client 6.7.3 Time Setting This item allows you to configure system’s time and the Daylight Saving Time. 6.7.3.1 Internet Time This page allows you to configure the Internet time setting. You can choose the “Automatically synchronize with internet time servers”. So the IG7600 can synchronize its system time with NTP time server automatically (Figure 6-92).
IG7600 Administration Manual Figure 6-93. Management – Time Setting – Internet Time – Manually 6.7.3.2 Daylight Saving Time This page allows you to configure the Daylight Saving Time (DST) which supports auto adjustment for daylight saving time. Click “Save Settings” button that you can save the new configuration. Click “Cancel Changes” button that you can cancel the changes. (Figure 6-94, Figure 6-95) Figure 6-94. Management – Time Settings – Daylight Saving Time Copyright 2013 Tecom, Co. LTD.
IG7600 Administration Manual Figure 6-95. Management –Time Settings – Day Light Saving Time – Manual DST Rule Default International DST Rule: Default DST Rule obey international standard rule. Manual DST Rule: Define your own DST Rule. Start Time of DST: The date and time to start daylight saving. If “Weekday” is 0, it means the date to start daylight saving is at exactly the given date. If “Weekday” is not 0, the DST starts on the “Weekday” on or after the given date.
IG7600 Administration Manual 6.7.4.2 Services A Service Control List enables or disables services from being used. (Figure 6-97) Figure 6-97. Management – Access Control –Services 6.7.4.3 IP Addresses If the Access Control mode is enabled, permits access to local management services from IP addresses contained in the Access Control List. If disabling the mode, it will not validate IP addresses for incoming packets.
IG7600 Administration Manual 6.7.4.4 Password In this page you can define the passwords for administrator, support, and user. The Administrator has unrestricted access to change and view configuration of your IG7600. The Support is used to allow an ISP technician to access your IG7600 for maintenance and to run diagnostics. The User can access the IG7600, view configuration settings and statistics, as well as, update the router’s software. Use the password field to enter up to 16 characters.
IG7600 Administration Manual 6.7.6 IP Camera IG7600 now provide 8 entries for IP Camera, You can either add IP Cameras automatically when you are configuring a tecom special supported IP Camera, or manually add an ordinary one. (Figure 6-101) Figure 6-101. Management – IP Camera Click add to add a new entry (Figure 6-102) Figure 6-102. Management – IP Camera-Add 6.7.7 Upgrade Software The new released software could be upgraded from the Local PC side or remotely.
IG7600 Administration Manual to process the software update. NOTE: The upgrade process takes about 5 minutes to complete, and your IG7600 will reboot. (Figure 6-103) Figure 6-103. Management – Upgrade Software 6.7.8 Upgrade Phone Software Upgrade Phone Software page is for you to manage your IP Phones’ software, when the IP Phone Extensions’ software is different from the one we stored in system, IG will ask the IP Phone to upgrade its software using the image we stored.
IG7600 Administration Manual Door Phone to upgrade its firmware using the image we stored. There are three FWs for Door Phone, one for voice part upgrading, and two for video part upgrading. You can delete the firmware if you don’t want to use it.(Figure 6-105) Figure 6-105. Management – Upgrade Door FW 6.7.10 APNS Certificate APNS Certificate page is for you to update your APNS certificate file for IG. You can use either Manual Mode or Auto Mode to update your certificate file.
IG7600 Administration Manual Figure 6-106. Management – APNS Certificate 6.7.11 Reboot Figure 6-107. Management – Save/Reboot Click “Reboot” to reboot the IG7600. The IG7600 would automatically save the configuration before reboot, so that modified settings would take effect after reboot. (Figure 6-107) Copyright 2013 Tecom, Co. LTD.
IG7600 Administration Manual 6.8 Diagnostics This page provides the following information to users: (Figure 6-108, 6-109) The network connection information on the net. The status of IG7600's PSTN Line. The status of IG7600’s IP Trunk Line. The status of IG7600’s AA Line. The status of IG7600’s FXS. The Missed Voice Files. Note: Displays only if there is any voice file missed. This column shows at most 5 missed files.
IG7600 Administration Manual Figure 6-109. Diagnostics - Missed Voice Files 6.9 Logout Press “Logout”, you can logout the IG7600 web configuration page. 6.10 Web UI Language Move your mouse to the upper right corner of the webpage, a list will pop up to show the languages you can choose. Now we support only English and Russian. (Figure 6-110) Figure 6-110. Web UI Language-Drop down list Copyright 2013 Tecom, Co. LTD.
IG7600 Administration Manual Appendix 1: Product Summary TCP/IP Protocols IP Protocol (791) ARP (RFC 826) / RARP (RFC 903) ICMP (RFC792) TCP (RFC 793) UDP (RFC 768) SNTP DNS HTTP Telnet IP Address Assignment Static Dynamic Subnet Mask PPPoE Client (RFC 2516) Primary and Secondary DNS DHCP Server (RFC 2131-2132) DHCP Client (RFC 2132) Dynamic DNS Routing RIP v1/v2 Static routing DHCP Server/Relay/Client DNS Relay NAT/NAPT NAT Traversal / Far End NAT Trave
IG7600 Administration Manual G.168 Echo Cancellation Voice Codec: G.711u, G.711a, G726-16, G726-24, G726-32 and G.726-40 (G.729a optional) Support FAX/modem tone detection and auto-fallback to G.711 T.38 Digital Audio Codec: G.711 a-law/μ-law 64Kbps, G.729 SIP Call Offer /Answer: Codec auto capacity exchange Echo Cancellation: G.
IG7600 Administration Manual Language Support English (North America) – default LED Status LED Name POWER WIRELESS LINE (1-4) TEL LAN WAN Color Red/Blue Blue Blue Blue Blue Red/Blue Status Description Red On Firmware updating Blue Flashing System booting up Blue On System initialized and running Off Power off On Wireless LAN is active Off Wireless LAN is idle Off PSTN Line is idle On PSTN Line is active Off Phone is idle On Phone is active On LAN is connected Off LAN is no
IG7600 Administration Manual Appendix 2: Feature Access Codes The Feature Access Codes are applied in IP2061/M62/M22 Phones, M54 Smart Phones and FXS phone only. It’s to activate/cancel some IG7600 user-specified functions. These Feature Access Codes are used when the phone is at idle state. Direct Call Forward Forward all of the calls without regard to the extension status. (Type: 0 – ICM, 1 – Outside, 2 – Both) To Activate *21 + Type + Ext/VAA/UCD No.
IG7600 Administration Manual To Activate *25 + Type + Ext No + * + Password To Cancel **25 + Ext No + * + Password Call Fork When extension gets an incoming call, the extension gets ringing. It rings another extension or rings an outside destination simultaneously.
IG7600 Administration Manual *622 + Admin. Password Remote Maintenance Simple Save *63 + Admin. Password Remote Maintenance *64 + Action Type [+ Log Level] + * + Admin. Password “Action Type”:1 – Enable; 2 – Disable; 3 – Save and send the tar ball file through email. “Log Level”: 0 – Error; 1 – Warning; 2 – Info; 3 – Debug Reset Feature Buttons Reset all feature buttons to IG7600’s setting. *68 + (Password) Reset To Default Selected IG7600 extension features can be returned to default setting.
IG7600 Administration Manual Agent Log On/Off It can control the status in an UCD group. To Activate (Log On) *91 To Cancel (Log Off) **91 Phone Lock/Unlock You can use the Lock feature to prevent unauthorized trunk calls from being made from extension.
