S TA RG A ZER FR -W1804- 52L s INSTALLATION INSTRUCTIONS WET DC MOTOR SMART works with the Google Assistant modernforms.
All Modern Forms Smart Fans are: WET SMART Durably finished and Rated for interior and exterior use Able to coordinate with smart devices for voice-activated and thermostat control Wet location-listed to the strictest ETL/ cETL safety regulations DC MOTOR Quiet, reliable, and up to 70% more efficient than AC fans Wi-Fi and RF enabled for unlimited control APP INSTRUCTIONS AND SMART HOME DEVICE INTEGRATION modernforms.
TABLE OF CONTENTS 1 SAFETY RULES.......................................................................................................................................... 4. 2 FTC ENERGY GUIDE & SPECIFICATIONS................................................................................................ 5. 3 TOOLS AND MATERIALS REQUIRED...................................................................................................... 5. 4 PACKAGE CONTENTS...........................................
1. SAFETY RULES For operation, maintenance, and troubleshooting information, visit modernforms.com/help. 1. 2. 3. 4. box and ungrounded conductor on the other side of the outlet box. 9. All set screws must be checked and re-tightened where necessary before installation. To reduce the risk of electric shock, ensure electricity has been turned off at the circuit breaker or fuse box before beginning.
2. FTC ENERGY GUIDE & SPECIFICATION FAN FAN SIZE VOLTS N.W (lbs) G.W (lbs) Stargazer 52” 120 16.14 19.31 STANDARD ELECTRICITY AIR FLOW ENERGY COSTS* FAN EFFICACY High Speed 38W 5822 CFM $11/yr 153.2 CFM/W Weighted Average 21W 3233 CFM $6/yr 154 CFM/W *Estimated annual energy cost based on $0.12 per kWh and 6.4 hours use per day. 3.
4. PACKAGE CONTENTS Unpack your fan and check the contents. You should have the following items: REF. DESCRIPTION PART NO.
5. MOUNTING OPTIONS Support Brace Joist If there isn’t an existing UL/cUL listed mounting box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Secure the outlet box directly to the building structure. Use appropriate fasteners and building materials. The outlet box and its support must be able to fully support the moving weight of the fan (at least 35 lbs). Do not use plastic outlet boxes.
6. HANGING THE FAN REMEMBER to turn off power at the breaker. Follow the steps below to hang your fan properly: 1. Disconnect power at the breaker to the fan location. A licensed electrician must install the fan (Fig. 5). 2. FIGURE 5 Remove 1 of 2 screws from the bottom of mounting bracket and save for use in section 9. Loosen the other screw (Fig. 6). 3. Pass the 120-volt supply wires through the center hole in the ceiling mounting bracket as shown in (Fig. 7). 4.
6. HANGING THE FAN (cont.) Cross Pin 1. Take out the screw located in the hanger ball, lower the hanger ball and Hanger Ball remove the cross pin. Remove the hanger ball from the hanger ball/ downrod assembly (Fig. 8). 2. Screw Remove the clevis pin and cotter pin, and loosen the two collar screws Downrod from the motor collar (Fig. 9). 3. Carefully feed the motor wires and safety cable up through the downrod. Thread the downrod into the collar. 4.
6. HANGING THE FAN (cont.) 1. Slip the coupling cover, canopy screw cover (painted side face down), and Safety Cable Motor Wires canopy (opened side up) onto the downrod (Fig. 10). Coupling cover goes all the way to the bottom. 2. Carefully reinstall the hanger ball onto the downrod, being sure that the Downrod Canopy cross pin is in the correct position, the screw is tightened and wires are not twisted (Fig. 10). 3.
7. MAKING THE ELECTRICAL CONNECTIONS WARNING: To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. WARNING: Installation of this fan requires that a three-conductor cable (including ground wire) should run between ceiling and wall outlet box. Mounting Bracket WARNING: Check to see that all connections are tight, including ground, and that no bare wire is visible at the wire nuts, except for the ground wire.
7. MAKING THE ELECTRICAL CONNECTIONS (cont.) Outlet box Motor to receiver electrical connections: (Fig. 13) 1. Connect the hanger ball/downrod assembly ground wire, mounting Black (hot) bracket ground wire and receiver ground wire to the ground wire in Black (“AC IN L”) outlet box. White (neutral) Green (ground) White (“AC IN N”) Green (ground) To hanger ball WARNING: Failure to connect ground wires could result in poor fan control functionality. 2. the receiver. 3.
8. INSTALLING THE WALL CONTROL Wall control to wall outlet box electrical connections: (Fig. 14) WARNING: Remember to shut the power off at the circuit breaker or fuse box. 1. Connect ground wires - Important for proper control function. 2. Connect the black wire marked “LINE IN” from the control to the black LINE VOLTAGE wire from the outlet box that feeds back to the breaker. 3. Connect the red wire from the control to the black wire from the wall outlet box that feeds up to the fan. 4.
8. INSTALLING THE WALL CONTROL (cont.) 1. Carefully tuck the wire connections inside the junction box. Secure the Wall Control wall control with the two wall control mounting screws provided (Fig. 15). 2. Attach the wall mounting plate over the wall control and secure with the Wall Outlet Box Wall Mounting Plate two wall mounting plate screws provided. 3. Fasten the wall plate to the wall mounting plate. NOTE: Maximum of 2 fans can operate on a circuit through the wall control.
9. FINISHING THE INSTALLATION 1. Secure all wire connections with supplied wire ties to assist in canopy installation. 2. Tuck connections neatly into ceiling outlet box. 3. Slide the canopy up to hanger bracket and place the key hole on the Outlet Box Hanger Bracket Screws canopy over the screw on the hanger bracket. Turn canopy until it locks in place at the narrow section of the key holes (Fig. 16). 4. Canopy Align the circular hole on canopy with the remaining hole on the hanger bracket.
FIGURE 17 10. ATTACHING THE FAN BLADES 1. Insert the blade through the slot in the housing. Align the holes in the blade with the fan motor assembly holes and secure with a blade attachment screw with rubber washers (Fig. 17). 2. Repeat this procedure with the remaining blades. Slot Blade 11. INSTALLING THE ADAPTER PLATE Screws with Rubber Washers FIGURE 18 1. Remove one of the three screws from the mounting ring and loosen the other two screws (do not remove). 2.
12. INSTALLING THE LED LUMINAIRE MODULE WARNING: Before starting installation, disconnect the power by turning off the circuit breaker or removing the fuse at fuse box. 1. Remove 1 of the 3 screws from the outer perimeter of the adapter plate and keep it for future use. Loosen the other 2 screws (do not remove). 2. Raise and hold the LED luminaire module close to the adapter plate and proceed to secure the wire connections.
13. WALL CONTROL OPERATING INSTRUCTIONS Your DC brushless motor is equipped with an intuitive wall control. Restore power to ceiling fan and test the wall control as below for proper operation. Pairing the Wall Control to Your Fan Your fan is pre-paired at the factory, no pairing is necessary. Wall Control Button Definitions These seven buttons are used to set the fan speed as follows: Button: turn the light ON or OFF Press/Hold to increase the desired light level.
13. WALL CONTROL OPERATING INSTRUCTIONS (cont.) NOTE: Maximum of 2 fans can operate on a circuit through the wall transmitter. Maximum of 12 fans can operate on a circuit through an on/off switch or breaker when utilizing the app for the fan control (without the wall control in the circuit). Summer mode - (Counter-clockwise) A downward airflow creates a cooling effect as shown in Fig. 21. This allows you to set your air conditioner on a warmer setting without affecting your comfort.
14. APPLICATION In addition to the included wall control, you can control the fan through the Modern Forms app. 1. To use the app, download it for free from the App Store or Google Play. 2. Open the app to create your account. You can also log in with your Facebook or FIGURE 23 FIGURE 24 Google account. 3. Next, set up a WiFi connection. You’ll need the SSID and WiFi password for the network you want to connect to. 4.
15. TROUBLESHOOTING Problem Solution Fan will not start. 1. Check circuit fuses or breakers. 2. Check wall control LED indicator light. If LED is not illuminated when pushing a button, it is not transmitting a signal. Please check power to wall control and all electrical connections. 3. Assure that there are no more than 2 fans operating on a circuit through the wall control.
16.
PRODUCT DOWNROD FR-W1804 MODEL DESCRIPTION FINISH XF-12 12 in downrod AS, CFI, LN, SS BZ, DW, GB, GH, GW, MB, MW, OB, TT XF-18 18 in downrod AS, CFI, LN, SS BZ, DW, GB, GH, GW, MB, MW, OB, TT XF-24 24 in downrod AS, CFI, LN, SS BZ, DW, GB, GH, GW, MB, MW, OB, TT XF-36 36 in downrod XF-48 48 in downrod AS, LN, SS BZ, DW, GB, GH, GW, MB, MW, OB, TT XF-60 60 in downrod AS, LN, SS BZ, DW, GB, GH, GW, MB, MW, OB, TT XF-72 72 in downrod AS, LN, SS BZ, DW, GB, GH, GW, MB, MW, OB, TT All ou
Español For instructions in Spanish, please visit the link below. Para obtener instrucciones en español, visite el siguiente enlace. www.modernforms.com/fan-instructions-espanol Français For instructions in French, please visit the link below. Pour obtenir des instructions en français, veuillez visiter le lien ci-dessous. www.modernforms.
Get Smart The Modern Forms app synchronizes seamlessly with smart home devices you already own. To learn more go to modernforms.com/mfappins works with the Google Assistant Free App Download Sync with our exclusive Modern Forms App to control fan speed, use smart features like Adaptive Learning, create groups and reduce energy costs. modernforms.
FR-W1 804 26
FR-W1804 27
FR -W1804- 52L modernforms.