A V IA TO R FR - W 1 8 1 1 - 5 4 s INSTALLATION INSTRUCTIONS WET DC MOTOR SMART works with the Google Assistant modernforms.
All Modern Forms Smart Fans are: WET SMART Durably finished and Rated for interior and exterior use Able to coordinate with smart devices for voice-activated and thermostat control Wet location-listed to the strictest ETL/cETL safety regulations DC MOTOR Quiet, reliable, and up to 70% more efficient than AC fans Wi-Fi and RF enabled for unlimited control APP INSTRUCTIONS AND SMART HOME DEVICE INTEGRATION modernforms.
TABLE OF CONTENTS 1. SAFETY RULES..............................................................................................................................................4 2. FTC ENERGY GUIDE & SPECIFICATION.....................................................................................................5 3. TOOLS AND MATERIALS REQUIRED..........................................................................................................5 4. PACKAGE CONTENTS.......................................
1. SAFETY RULES For operation, maintenance, and troubleshooting information, visit modernforms.com/help. 1. 2. 3. 4. 5. 6. 7. 8. To reduce the risk of electric shock, ensure electricity has been turned off at the circuit breaker or fuse box before beginning. box and ungrounded conductor on the other side of the outlet box. 9. All set screws must be checked and re-tightened where necessary before installation.
2. FTC ENERGY GUIDE & SPECIFICATION FAN FAN SIZE VOLTS N.W. (lbs) G.W. (lbs) Aviator 54” 120 6.14 9.69 STANDARD ELECTRICITY AIR FLOW ENERGY COSTS* FAN EFFICACY High Speed 26W 7554 CFM $7/yr 295.1 CFM/W Weighted Average 16W 4370 CFM $4/yr 280 CFM/W * Estimated annual energy cost based on $0.12 per kWh and 6.4 hours use per day. 3.
4. PACKAGE CONTENTS REF. Unpack your fan and check the contents. You should have the following items: DESCRIPTION PART NO.
4. PACKAGE CONTENTS (cont.
5. MOUNTING OPTIONS Support Brace Joist If there isn’t an existing UL/cUL listed mounting box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Secure the outlet box directly to the building structure. Use appropriate fasteners and building materials. The outlet box and its support must be able to fully support the moving weight of the fan (at least 35 lbs). Do not use plastic outlet boxes.
6. INSTALLING THE MOUNTING BRACKET REMEMBER to disconnect the power by removing fuses or turning off circuit breakers. Follow the steps below to hang your fan properly: 1. Disconnect power to the fan location. A licensed electrician must install the fan if required by your local electrical code (Fig. 5). 2. FIGURE 5 Remove 1 of 2 screws from the bottom of the mounting bracket and loosen the other screws. 3.
7. ATTACHING THE FAN BLADES 1. Blade collector ring Place fan blade on motor as shown in Figure 8 and secure with the blade attachment screws and washers. 2. Repeat this procedure with the remaining blades (Fig 8). 3. Secure the bottom of the fan blades together using the provided blade collector ring and hardware (Fig 9). 8. ATTACHING DECORATIVE LOWER CAP 1. Tightly twist the decorative lower cap onto the motor assembly (Fig 10).
9. HANGING THE FAN 1. Remove the clevis pin and cotter pin and loosen the two collar screws from the motor collar (Fig. 11). 2. Feed motor wires through coupling cover, canopy ring, and canopy 3. Feed motor wire through downrod assembly. 4. Thread the downrod assembly onto motor collar. Align the holes of downrod and collar and insert the cotter pin and clevis pin. Tighten the two collar screws (Fig. 11).
9. HANGING THE FAN (cont.) 1. Carefully lift the fan motor assembly up to the mounting bracket and seat the hanger ball in the mounting bracket socket. Safety cable Make sure the tab on the mounting bracket socket is properly seated in the groove in the hanger ball (Fig. 12). Rotate the socket assembly until the ball drops and locks into the hanger bracket screw. 2. Secure the safety cable to the building structure using spring washer, flat washer, and wood screw provided (Fig. 12).
10. MAKING THE ELECTRICAL CONNECTIONS REMEMBER to disconnect the power by removing fuses or turning off circuit breakers. Follow the steps below to hang your fan properly: WARNING: To avoid possible electrical shock, be sure electricity is Mounting bracket turned off at the main fuse box before wiring. WARNING: Installation of this fan requires that a three-conductor cable (including ground wire) which should run between ceiling and wall outlet box.
10. MAKING THE ELECTRICAL CONNECTIONS (cont.) Outlet box Motor to receiver electrical connections: (Fig. 14) 1. Connect the hanger ball/downrod assembly ground wire, mounting bracket ground wire and receiver ground wire to the ground White (neutral) Green (Ground) Black (hot) Black (“AC IN L”) White (“AC IN N”) wire in outlet box. Green (Ground) WARNING: Failure to connect ground wires could result in poor fan control functionality. 2. MOTOR” from the receiver. 3.
11. INSTALLING THE WALL CONTROL WARNING: Remember to shut the power off at the circuit breaker or fuse box. Wall control to wall outlet box electrical connections: (Fig. 14) 1. Connect ground wires - Important for proper control function. 2. Connect the black wire marked “LINE IN” from the control to the black LINE VOLTAGE wire from the outlet box that feeds back to the breaker. 3. Connect the red wire from the control to the black wire from the wall outlet box that feeds up to the fan. 4.
11. INSTALLING THE WALL CONTROL (cont.) 1. Carefully tuck the wire connections inside the junction box. Wall control Secure the wall control with the two wall control mounting screws provided. (Fig. 15) 2. Wall outlet box Wall mounting plate Attach the wall mounting plate over the wall control and secure with the two wall mounting plate screws provided. 3. Fasten the wall plate to the wall mounting plate. NOTE: A maximum of 2 fans can operate on a circuit through the wall control.
12. FINISHING THE INSTALLATION 1. Secure all wire connections with supplied wire ties to assist in canopy installation. 2. Tuck connections neatly into ceiling outlet box. 3. Slide the canopy up to the mounting bracket and place the key hole on the canopy over the screw on the mounting bracket. Turn canopy until it locks in place at the narrow section of the key holes (Fig. 16). 4. Align the circular hole on the canopy with the remaining hole on the mounting bracket.
13. INSTALLING THE LED LUMINAIRE MODULE (Optional Accessory) FIGURE 18 FIGURE 19 FIGURE 20 FIGURE 21 REMEMBER to disconnect the power by removing fuses or turning off circuit breakers. Follow the steps below to hang your fan properly: 1. Remove the three screws from the LED wire storage cap. Keep the cap for future use when not using the luminaire (Fig. 18). 2. Install the LED mount plate using 3 screws removed from Step 1 (Fig. 19). 3.
14. WALL CONTROL OPERATING INSTRUCTIONS Your DC brushless motor is equipped with an intuitive wall control. Restore power to ceiling fan and test the wall control as below for proper operation. Pairing the Wall Control to Your Fan Your fan is pre-paired at the factory, No pairing is necessary. Wall Control Button Definitions These seven buttons are used to set the fan speed as follows: Button: turn the light ON or OFF Press/Hold to increase the desired light level.
14. WALL CONTROL OPERATING INSTRUCTIONS (cont.) NOTE: Maximum of 2 fans can operate on a circuit through the wall transmitter. Maximum of 12 fans can operate on a circuit through an on/off switch or breaker when utilizing the app for the fan control (without the wall control in the circuit). Summer mode - (Counter-clockwise) A downward airflow creates a cooling effect as shown in Fig. 21. This allows you to set your air conditioner on a warmer setting without affecting your comfort.
15. APPLICATION In addition to the included wall control, you can control the fan through the Modern Forms app. 1. To use the app, download it for free from the App Store or Google Play. 2. Open the app to create your account. You can also log in with your FIGURE 26 FIGURE 27 Facebook or Google account. 3. Next, set up a WiFi connection. You’ll need the SSID and WiFi password for the network you want to connect to. 4.
16. TROUBLESHOOTING Problem Solution Fan will not start. 1. Check circuit fuses or breakers. 2. Check wall control LED indicator light. If LED is not illuminated when pushing a button, it is not transmitting a signal. Please check power to wall control and all electrical connections. 3. Assure that there are no more than 2 fans operating on a circuit through the wall control.
17.
PRODUCT DOWNROD FR-W1811 MODEL DESCRIPTION FINISH XF-12 12 in downrod AS, CFI, LN, SS BZ, DW, GB, GH, GW, MB, MW, OB, TT XF-18 18 in downrod AS, CFI, LN, SS BZ, DW, GB, GH, GW, MB, MW, OB, TT XF-24 24 in downrod AS, CFI, LN, SS BZ, DW, GB, GH, GW, MB, MW, OB, TT XF-36 36 in downrod XF-48 48 in downrod AS, LN, SS BZ, DW, GB, GH, GW, MB, MW, OB, TT XF-60 60 in downrod AS, LN, SS BZ, DW, GB, GH, GW, MB, MW, OB, TT XF-72 72 in downrod AS, LN, SS BZ, DW, GB, GH, GW, MB, MW, OB, TT All ou
Español For instructions in Spanish please visit the link below. Para obtener instrucciones en español, visite el siguiente enlace. www.modernforms.com/fan-instructions-espanol Français For instructions in French please visit the link below. Pour obtenir des instructions en français, veuillez visiter le lien ci-dessous. www.modernforms.
Get Smart The Modern Forms app synchronizes seamlessly with smart home devices you already own. To learn more go to modernforms.com/mfappins works with the Google Assistant Free App Download Sync with our exclusive Modern Forms App to control fan speed, use smart features like Adaptive Learning, create groups and reduce energy costs. modernforms.
FR- W1 8 1 1 27
FR- W 1 8 1 1 modernforms.