Use and Care Manual

Modern Masters
Revised May 2011
Page 2 of 3
Substrates: aluminum, anodized metals, copper
piping, window and door mullions.
• Mathys Peganox by Rustoleum
Substrates: rusting metal, slag metal
For MSDS and Technical Data Sheets for these primers
go to modernmasters.com
and search in our technical
section of the web site.
For Additional Information and Architectural
Specifications visit ARCAT.com
and search for
Modern Masters Inc. or a specific product name.
Application – Modern Masters Metal Effects paints can
be brushed, rolled, or spray applied (See specific
equipment requirements under Spraying) onto any
paintable, properly primed, interior or exterior surface,
such as walls, ceilings, columns, trim, doors, furniture,
and paintable wallcoverings. Always test the product in
a small, inconspicuous area before beginning a project
to see if the desired results are attained. We
recommend preparing a sample board prior to
beginning a project to check color and technique. The
paint should be mixed thoroughly before using. Do not
apply in temperatures below 55°F/13°C or above
85°F/29°C.
Step 1: Apply first coat of Metal Effects Bronze Paint
and allow to dry.
Step 1: Apply a second coat of Metal Effects Bronze
Paint in the same manner. The Blue or Green Patina
Aging Solution should be applied while this coat is still
wet (within 5 minutes).
Brushing: Use a high-quality brush recommended for
water base semi-gloss paints.
Rolling: To roll Metal Effects Bronze Paint use a high-
end ½” nap roller and/or a natural sea sponge roller for
added effect.
Spraying: To spray Metal Effects Bronze Paint, thin
with up to 16 fluid ounces/473 milliliters of water to one
gallon/3.78 liters of Metal Effects Bronze Paint. Thin
carefully, as over thinning of the paint will result in loss
of hide and a reduction of the desired appearance. Use
an HVLP gun or a conventional cup gun with the fluid
and air supply from a pressure pot and compressor. Air
pressure at the HVLP spray gun needs to be
approximately 30 psi, with greater pressures at the tank,
approximately 60 psi. Examples: Binks-Mach 1 HVLP,
with a 94-nozzle set up (0.55 or 1.4mm diameter fluid
tip and a 90P air nozzle). The settings for this
equipment were: Fluid Pressure-25psi and Air
Pressure-45psi. Binks-2001 Conventional, with a
66SS air nozzle set up (0.70 or 1.8 fluid tips and a
66SD air nozzle). The settings for this equipment were:
Fluid Pressure-30psi and Air Pressure-60psi. Use a
NIOSH approved respirator when spraying. Provide
adequate ventilation. Note: Do not use turbine-type
“air compressors” to power the HVLP spray gun
and do not use airless spray systems.
Taping – Use high quality, low-tack tape when taping
over surfaces that have been previously painted with
Metallic Paint. When painting over taped-off areas be
aware that Metallic Paints exhibit poor early adhesion
properties and are elastomeric (they stretch) before
curing. Consider cutting along the tape edge with a
razor blade to avoid delaminating the fresh paint from
the substrate.
Dry Times – Recoat time is approximately ½ hour.
Dry-to-touch time is approximately an hour. (Drying
times were recorded at 70°F and 50%RH): Note: Lower
temperature and/or higher humidity will lengthen the dry
and cure times.
Coverage – One gallon/3.78 liters will cover
approximately 320 square feet/29.7 square meters.
Approximately 1.5 mils dry film thickness per coat. A
minimum of 3 mils dry film thickness is required for hide
and full color development.
Step 2: Apply the Blue or Green Patina Aging Solution
with a brush, sea sponge or spray apply with a plastic
pump sprayer. After 5 minutes, reapply Patina Aging
Solution. As the activated surface dries (approx. 30-40
min.) a real patina finish will appear. Cold temperature
and/or humid conditions will prolong the oxidation
process and dry time.
Protective Clear Coating – Patina finishes do not
require a clear protective finish, except if the patina
surface is subject to repeated hand contact, such as
hand rails. If a protective sealer/topcoat is desired, use
Metal Effects Permacoat Xtreme (AM204). DO NOT
USE OTHER SEALERS OR VARNISHES. Permacoat
Xtreme can be applied by brush, roller or spray. Surface
must be completely dry prior to top coating. First coat:
Add equal parts of Permacoat Xtreme with water and
stir well before applying. Second coat: Apply
Permacoat Xtreme at full strength. Let surface dry for 1
hour before handling. Full cure time is 7 to 10 days.
Clean Up – Clean brushes, rollers, tool, and equipment
with soap and warm water immediately after use. Do
not reuse containers and properly dispose of empty
containers.
VOC – Metal Effects Bronze Paint contains less than
50g/L. Metal Effects Primer contains less than 100 g/L.
Metal Effects Permacoat Xtreme contains less than 100
g/L.
Handling & Storage – Close tightly all containers when
not in use. Store in a cool dry place away from direct
sunlight. Do not freeze. If Metal Effects Bronze Paint
becomes frozen, allow the paint to completely thaw and
come to room temperature before use. Stir thoroughly
before use.
Disposal – Dispose of unused or unwanted product in
accordance with local laws regulating water-based
coatings.
Health & Safety – Use in a well-ventilated area. Avoid
contact with eyes. Wash hands thoroughly with soap