Installation Guide

ManualsBrandsMOEN ManualsBathAshville 1-Handle Shower Faucet in Spot Resist Brushed Nickel

E10

E11

English

Remove the lever (L)

and lever handle

adapter (J).

Note the position of

the stop. Position the

adjustable tempera-

ture limit stop (D) so

the lever or knob stops

at that position. This

prevents the lever or

knob from being

turned into an unsafe

temperature.

Remove the knob han-

dle (P). Note the posi-

tion of the stop.

Position the adjustable

temperature limit stop

(D) so the lever or knob

stops at that position.

This prevents the lever

or knob from being

turned into an unsafe

temperature.

5.3

After setting the adjustable

temperature limit stop to the

desired position, remove the

lever (L), reattach the lever

handle adapter (J), adapter

screw (K), and lever (L) – make

sure ridges on back of (J) are to

the left of the tab on (D).

After setting the adjustable

temperature limit stop to

the desired position, reat-

tach the double D washer

(O) and knob (P) – make

sure indicator on the knob

is pointing down.

5.4

Moen Lifetime Limited Warranty

Moen products have been manufactured under the highest standards of quality and

workmanship. Moen warrants to the original consumer purchaser for as long as the original

consumer purchaser owns their home (the “Warranty Period” for homeowners), that this faucet

will be leak- and drip-free during normal use and all parts and finishes of this faucet will be free

from defects in material and manufacturing workmanship. All other purchasers (including

purchasers for industrial, commercial and business use) are warranted for a period of 5 years

from the original date of purchase (the “Warranty Period” for non-homeowners).

If this faucet should ever develop a leak or drip during the Warranty Period, Moen will FREE OF

CHARGE provide the parts necessary to put the faucet back in good working condition and will

replace FREE OF CHARGE any part or finish that proves defective in material and manufacturing

workmanship, under normal installation, use and service. Replacement parts may be obtained

by calling 1-800-289-6636 (Canada 1-800-465-6130), or by writing to the address shown. Proof

of purchase (original sales receipt) from the original consumer purchaser must accompany all

warranty claims. Defects or damage caused by the use of other than genuine Moen parts is not

covered by this warranty. This warranty is applicable only to faucets purchased after December,

1995 and shall be effective from the date of purchase as shown on purchaser’s receipt.

This warranty is extensive in that it covers replacement of all defective parts and finishes.

However, damage due to installation error, product abuse, product misuse, or use of cleaners

containing abrasives, alcohol or other organic solvents, whether performed by a contractor,

service company, or yourself, are excluded from this warranty. Moen will not be responsible for

labor charges and/or damage incurred in installation, repair or replacement, nor for any indirect,

incidental or consequential damages, losses, injury or costs of any nature relating to this faucet.

Except as provided by law, this warranty is in lieu of and excludes all other warranties, conditions

and guarantees, whether expressed or implied, statutory or otherwise, including without

restriction those of merchantability or of fitness for use.

Some states, provinces and nations do not allow the exclusion or limitation of incidental or

consequential damages, so the above limitations or exclusions may not apply to you. This

warranty gives you specific legal rights and you may also have other rights which vary from

state to state, province to province, nation to nation. Moen will advise you of the procedure to

follow in making warranty claims. Simply write to Moen Incorporated using the address below.

Explain the defect and include proof of purchase and your name, address, area code and

telephone number.

Moen Incorporated

25300 Al Moen Drive, North Olmsted, Ohio 44070-8022 U.S.A.

Using 7/64 inches hex wrench

(N), insert and tighten hex

screw (M) into lever (L).

OR insert 1-1/2 inch Phillips

screw (Q). Tighten screw

and insert cap (R).

5.5

Turn on the hot and cold

water supply to check for

leaks and set temperature

limit stop.

5.1

HOTTEST

120F

(49C)

HOTTEST

120F

(49C)

Rotate the lever OR knob counterclockwise until the water is to the

maximum desired temperature, not to exceed 120 degrees F

(49 degrees C). Seasonal maintenance of the maximum outlet

temperature may be required due to changes in

groundwater temperature. TURN LEVER OR KNOB TO THE OFF

POSITION ONCE THE TEMPERATURE IS SET.

If temperature exceeds 120 degrees, go to step 5.3.

If temperature is less than 120 degrees, go to step 5.4.

5.2

Setting The Temperature Limit Stop and Finishing Your

Tub/Shower Installation