Installation Guide

ManualsBrandsMOEN ManualsBathDarcy 8 in. Widespread 2-Handle Bathroom Faucet in Spot Resist Brushed Nickel

Installation Guide

Guía de Instalación

Guide d’installation

Plumber’s Putty or Non-Staining Sealant

Masilla de plomero o sellador que no mancha

Mastic de plombier ou agent d'étanchéité non tachant

HERRAMIENTAS ÚTILES

Para que el cambio de la llave sea fácil y

seguro, Moen le recomienda usar estas

útiles herramientas.

OUTILS UTILES

Par mesure de sécurité et pour faciliter

l’installation, Moen suggère l’utilisation des

outils suivants.

HELPFUL TOOLS

For safety and ease of faucet replacement,

Moen recommends the use of these

helpful tools.

Please Contact Moen First

For Installation Help, Missing or

Replacement Parts

(USA)

1-800-BUY-MOEN (1-800-289-6636)

Mon - Fri 8:00 AM to 7:00 PM, Eastern

Sat. 9:00 AM to 3:00 PM Eastern

WWW.MOEN.COM

(Canada)

1-800-465-6130

Mon - Fri 7:30 AM to 7:00 PM, Eastern

WWW.MOEN.CA

Por favor, contáctese primero con Moen

Para obtener ayuda de instalación, piezas

faltantes o de recambio

01-800-718-4345

Lunes a viernes de 8:00 a 20:00 hs.

(Costa Este)

Sáb. 8:00 a 18:30 hs. (Costa Este)

WWW.MOEN.COM.MX

Veuillez d’abord contacter Moen

en cas de problèmes avec l’installation, ou pour

obtenir toute pièce manquante ou de rechange

1-800-465-6130

Du lundi au vendredi :

de 7 h 30 à 19 h, HE

WWW.MOEN.CA

INS10391 - 10/14

TWO HANDLE LAVATORY FAUCET

MEZCLADORA PARA LAVABO

DE DOS MANERALES

ROBINET DE LAVABO À DEUX POIGNÉES

Summary of content (12 pages)

PAGE 1
INS10391 - 10/14 Installation Guide Guía de Instalación Guide d’installation Please Contact Moen First For Installation Help, Missing or Replacement Parts (USA) 1-800-BUY-MOEN (1-800-289-6636) Mon - Fri 8:00 AM to 7:00 PM, Eastern Sat. 9:00 AM to 3:00 PM Eastern WWW.MOEN.COM (Canada) 1-800-465-6130 Mon - Fri 7:30 AM to 7:00 PM, Eastern WWW.MOEN.CA Por favor, contáctese primero con Moen Para obtener ayuda de instalación, piezas faltantes o de recambio 01-800-718-4345 Lunes a viernes de 8:00 a 20:00 hs.
PAGE 2
Parts List O M A. B. C. D. E. F. G. H. I. A x2 P B C x2 x2 F x2 J. K. L. M. N. O. P. Hose Lubricant Hot Valve Body Mounting Tool Hex Wrench Product ID Label Aerator Tool J. K. L. M. N. O. P. Manguera Lubricante Cuerpo de válvula caliente Herramienta de montaje Llave hexagonal Etiqueta de identificación del producto Herramienta del aireador J. K. L. M. N. O. P.
PAGE 3
INS10391 - 10/14 Parts List Waste Assembly Ensamblaje del desagüe Assemblage de la bonde R Q. R. S. T. U. V. W. Q Plug Lift Rod Pivot Rod Clip Waste Seat Drain Gasket Drain Washer Drain Nut X. Y. Z. AA. BB. CC. Drain O-Ring Pivot Rod Seat Tail Piece Pivot Rod Pivot Rod Nut Lift Rod Strap X. Y. Z. AA. BB. CC. Anillo de caucho del desagüe Asiento del pivote Sección final Pivote Tuerca del pivote Tirante de la barra de cierre vertical X. Y. Z. AA. BB. CC.
PAGE 4
1 2 B Sealant Sellador Mastic B Apply a bead of plumbers putty or other sealant to the base of the spout (B) as shown. Turn spout upright. Place the spout assembly (B) into center opening in sink. Coloque el conjunto del surtidor (B) en la abertura central del fregadero. Aplique una gota de masilla de plomero u otro sellador a la base del surtidor (B) como se muestra. Dé vuelta el surtidor a su posición normal. Placer l’assemblage du bec (B) dans l’ouverture centrale de l’évier.
PAGE 5
INS10391 - 10/14 5 6 B D I D Sealant Sellador Mastic M Use mounting tool (M) and Phillips screwdriver to tighten the mounting nut (I) to the spout base (B). Apply a generous bead of plumbers putty or other sealant to underside of the upper mounting washers (D). A putty groove is provided for this purpose. Turn washers (D) over and position on sink as shown. Use la herramienta de montaje (M) y un destornillador Phillips para apretar la tuerca de montaje (I) a la base del surtidor (B).
PAGE 6
8 9 C G Red = Hot Rojo = Caliente Rouge = Chaud B C Blue = Cold Azul = Frio Bleu = Froid L Slide clip (C) into the groove on each valve body. Check to see that each valve body outlet connection below the deck points towards the spout shank (B) as shown. Push the hot valve body (L) on the left side up from below the sink. Use one hand to hold one valve body and the other hand to insert the clip (C) as shown in step 9. Repeat for valve body (G).
PAGE 7
INS10391 - 10/14 12 13 L B G J Click Clic Cliquez sur G L Follow the same procedure as in step 11 to attach the hose (J) to the valve bodies (L & G). Listen for the “click” and tug to test engagement. Rotate the red stem extension on the hot valve body (L) clockwise and the blue stem extension on the cold valve body (G) counterclockwise until they stop. Siga el mismo procedimiento que en el paso 11 para conectar la manguera (J) a los cuerpos de válvula (L & G).
PAGE 8
15 16 W T T X Sealant Sellador Mastic correct orientation orientación correcta orientation correcte T W Z U V T Position the drain o-ring (X) in the groove at the top of the tail piece (Z) and thread onto the waste seat (T). After (Z) is attached to (T), rotate entire assembly so opening on (Z) points towards the wall. Now tighten drain nut (W). Remove excess sealant.
PAGE 9
INS10391 - 10/14 18 19 BB 2 1 Y B R 3 AA 19A 19B Q CC Q Install lift rod (R) into opening on the top of the spout (B). From under the sink, slide the lift rod strap (CC) onto pivot rod (R) and tighten the bolt finger tight. Final tightening will be completed during step 21. Verify white plastic pivot rod seat (Y) is in place with beveled side facing out. The pivot rod (AA) can be installed in two ways. Illustration (19A) shows the pivot rod (AA) next to hole in plug (Q).
PAGE 10
21 1. Loosen nut on liftrod strap (CC) to allow lift rod to rest in faucet. 2. Verify pivot rod (AA) is still pushed down, and plug (Q) is open in the sink. 3. Tighten bolt with wrench. 1. Afloje la tuerca en el tirante de la barra de cierre vertical (CC) para permitir que la barra de cierre vertical descanse sobre la mezcladora. 2. Verifique que el pivote (AA) todavía esté empujado hacia abajo, y que el tapón (Q) esté abierto en el fregadero. 3. Apriete el perno con una pinza. 2 AA 1.
PAGE 11
INS10391 - 10/14 24 O 3 25 Cold Frio Froid 1 0 4 Hot Caliente Chaud 15 Sec. 45 30 P 5 Place product ID label (O) here. 2 Coloque la etiqueta de identificación del producto (O) aquí. Placer l'étiquette d'identification du produit (O) ici. To flush debris from the plumbing system: 1. Remove the aerator by using the included aerator tool (P). Ensure aerator and aerator tool are engaged. Turn clockwise to loosen and remove aerator. 2. Turn faucet handles on and run hot and cold water for 15 seconds.
PAGE 12
Moen Limited Lifetime Warranty Moen products have been manufactured under the highest standards of quality and workmanship. Moen warrants to the original consumer purchaser for as long as the original consumer purchaser owns their home (the “Warranty Period" for homeowners), that this faucet will be leak- and drip-free during normal use and all parts and finishes of this faucet will be free from defects in material and manufacturing workmanship.