Specification Sheet

MOLDEX-METRIC, INC.
10111 W. Jefferson Blvd. Culver City, CA 90232
TEL: [phone] or [phone] FAX [phone]
www.moldex.com e-mail: [e-mail]
CANADIAN CUSTOMER SERVICE
TEL: [phone], Ext. 517
FAX: [phone]
Moldex, Ideas that wear well, Respirator Locker, Softspun and Dura-Mesh
are registered trademarks of Moldex-Metric, Inc.
The mesh design is a trademark of Moldex-Metric, Inc.
U.S. Patents #D285,374 and #4,850,347
Made in the U.S.A. 9700-768 REV H 06/09
PACKAGING
2200N95, Medium/Large 2250 Respirator Locker
2201N95, Small with 2200N95
2207N95, Low Profile 5 Respirators per Locker
20 Respirators per Box 27 Lockers per Case
12 Boxes per Case
LIMITED WARRANTY IMPORTANT
NOTICE TO PURCHASER
TThhiiss lliimmiitteedd wwaarrrraannttyy iiss mmaaddee iinn lliieeuu ooff tthhee wwaarrrraannttiieess ooff mmeerrcchhaannttaabbiilliittyy,,
ffiittnneessss ffoorr ppaarrttiiccuullaarr ppuurrppoosseess aanndd aallll ootthheerr wwaarrrraannttiieess,, eexxpprreessss oorr iimmpplliieedd..
There are no other warranties which extend beyond the description on
the face hereof. The physical standards and specifications of Moldex will
be met by products sold.
EExxcclluussiivvee RReemmeeddiieess::
damages for the breach of
this limited warranty are limited to the replacement of such quantity of
Moldex products proved to be defectively manufactured. Except as
provided above, Moldex shall not be liable or responsible for any loss,
damages, or liability, direct, indirect, incidental, special or consequential,
arising out of a sale, use or misuse, or the inability to use products by
the user.
DISTRIBUTED BY:
THESE RESPIRATORS ARE APPROVED ONLY IN THE FOLLOWING CONFIGURATIONS
Moldex-Metric, Inc.
CULVER CITY, CALIFORNIA, 90232
[phone]
N95 Particulate Filter (95% filter efficiency level) effective
against particulate aerosols free of oil; time use restrictions
may apply
A- Not for use in atmospheres containing less than 19.5 percent oxygen.
B- Not for use in atmospheres immediately dangerous to life or health.
C- Do not exceed maximum use concentrations established by regulatory standards.
J- Failure to properly use and maintain this product could result in injury or death.
M- All approved respirators shall be selected, fitted, used, and maintained in accordance with MSHA, OSHA, and other applicable
regulations.
N- Never substitute, modify, add, or omit parts. Use only exact replacement parts in the configurations as specified by the
manufacturer.
O- Refer to user's instructions, and/or maintenance manuals for information on use and maintenance of these respirators.
P- NIOSH does not evaluate respirators as surgical masks.
N95
A B C J M N O P
RESPIRATOR
TC-
PROTECTION
1
CAUTIONS AND LIMITATIONS
2
84A-0327
N95
N95
84A-2456
84A-2438
2200N95
2201N95
2207N95
X
X
X
A B C J M N O P
A B C J M N O P
1. Protection
2. Cautions and Limitations
WARNING TO USER
1. Follow all instructions and warnings on the use of this respirator and wear
during all times of exposure. Failure to do so will reduce respirator effective-
ness, wearer protection and may result in sickness or death.
2. Before use, the user must first be trained by the employer in proper respirator
use, in accordance with applicable safety and health standards, for the
contaminant and exposure level in the assigned work area.
3. The particulates and other contaminants which can be dangerous to your
health include those which you cannot see, taste, or smell.
4. This product has not been sold with warnings or use instructions for personnel
involved in healthcare or re l a ted situations, where there may be the
possibility of contact with disease or biological hazards. If you are considering
such uses, first call the Moldex Technical Service Dept., [phone]
ext. 512/550 or [phone] ext. 512/550.
!
USE AGAINST:
1. Particulate aerosols free of oil.
DO NOT USE AGAINST:
1. Concentrations of contaminants which are unknown, or are
immediately dangerous to life or health.
2. Concentrations of particulates which exceed the maximum use
concentration or 10 times the OSHA Permissible Exposure
Limit, whichever is lower.
3. Gases, vapors, asbestos, paint spray, sandblasting or
particulate materials which generate harmful vapors.
4. Oil-based mists.
RESTRICTIONS
1. This respirator does not supply oxygen and must not be used
in atmospheres containing less than 19.5% oxygen.
2. Do not remain in contaminated area if any physical distress
occurs, for example breathing difficulty, dizziness or nausea.
3. Leave contaminated area and replace respirator if it is
damaged, distorted, a proper fit can not be obtained or
breathing becomes difficult.
4. Prior to each use, carefully inspect the entire respirator,
including
filter media and strap/weld attachment area for
tears and damage. Staple or strap/weld attachment perfora-
tions do not affect respirator performance.
5. Do not alter, modify, or abuse this respirator.
6. Store unused respirators in box/bag in a clean, dry,
non-contaminated area.
7. Dispose of respirator according to your employer’s policy
and local regulations.
8. Dispose no later than thirty days after first use.
9. Use respirator before the “use by” expiration date printed on
box/bag.
10. If used for welding, wear appropriate eye and face
protection.
TECHNICAL SERVICE HELP LINE
For technical assistance, call Moldex Technical Service Department
at [phone] ext. 512/550 or [phone] ext.
512/550.
Ideas that wear well.
®