Instruction manual

12
2 Important Notes
The unit corresponds to all required directives of the
EU and is therefore marked with .
●
The receiver is suitable for indoor use only. Protect
it against impurities, dripping water and splash
water, high air humidity, and extreme temperatures
(admissible ambient temperature range
- 10 °C to
+55 °C).
●
For cleaning only use a dry, soft cloth, by no means
chemicals or water.
●
No guarantee claims for the unit and no liability for
any resulting personal damage or material damage
will be accepted if the unit is used for other purposes
than originally intended, if it is not correctly connect-
ed, operated, or not repaired in an expert way.
3 Applications
In combination with a 5.8 GHz transmitter or a 5.8 GHz
wireless surveillance camera of the “AV-58...” series
from MONACOR, the receiver AV-5810RDX serves
for wireless audio and video transmission. With addi-
tional units of the MONACOR product range a wire-
less video surveillance system can be set up.
The transmission range largely depends on the
local conditions, the transmitter used, and the recep-
tion antenna used. In the open, the range can be up
to 500 m, in buildings up to 40 m depending on the
condition of the walls and ceilings. By using an
antenna with gain, the range can considerably be
increased.
4 Setting into Operation
4.1 Placing the transmitter and receiver
Practical experience has shown that an optimum
reception is achieved when placing the units at a mini-
mum height of 1.5 m to 2 m above the ground. To find
a good place of mounting, a trial run is recommended.
The transmission quality can be substantially changed
by displacing the transmitter and/or the receiver by a
few centimetres only. To assess the receiving quality,
the receiving level indication “Level” can be inserted
on the screen. For this purpose shortly press the but-
ton “OK” (7) three times (also see chapter 5.1).
4.2 Connecting the units
Prior to connecting the units or changing existing
connections switch off the AV-5810RDX and all other
units of the surveillance system.
When selecting the audio outputs, pay attention
that the audio level (volume) can be adjusted at the
jacks “audio A” (10) and “audio B” (11) with the but-
tons “L-” and “L+” (5), however, not the audio level at
the jack “DIN-AV” (9).
4.2.1 Surveillance monitor
1) Connect the video input of the monitor to the jack
“video” (12) via a 75 Ω coaxial cable.
2) If a sound is transmitted as well, connect the audio
input of the monitor via a screened audio cable to
the jack “audio A” (10) and in case of a stereo
sound additionally to the jack “audio B” (11).
4.2.2 TV set
A TV set can also be connected instead of a monitor.
1) Depending on the existing jacks on the TV set,
connect the AV-5810RDX via the jack “DIN-AV” (9)
or via the jacks “audio A” (10), “audio B” (11), and
“video” (12) to the TV set.
2) If the TV set is equipped with a scart jack, connect
this jack via an adapter (e. g. VAI-3 from
MONACOR) to the jacks “audio A” (10), “audio B”
(11), and “video” (12).
3) If the TV set is not equipped with one of the input
jacks mentioned before, connect an AV modulator
(e. g. VAM-3 from MONACOR) to the jack “video”
(12) and, if required, to the jack “audio A” (10).
Place the modulator between the TV antenna and
the antenna jack of the TV set.
4.2.3 Video recorder, second monitor, or second
TV set
1) For audio and video recording a video recorder
may be connected to the jack “DIN-AV” (9).
Depending on the existing connection jacks on the
video recorder an adapter may be required.
2) Alternatively a second monitor or a second TV set
may be connected to the jack “DIN-AV” for parallel
surveillance. If required, use a matching adapter.
4.2.4 Signal devices or other additional units
To control visual or acoustical signal devices or other
additional units, two relay outputs are available which
allows switching of voltages of up to 42 V at 500 mA
as a maximum:
1. As soon as a perfect video signal is received, the
contacts “AV channel” (14) will be closed.*
2. If the transmitter used is equipped with a control
channel and if this control channel is activated
(e. g. by a motion detector), the contacts “switching
channel” (14) will be closed.*
If the unit is to be put out of operation defini-
tively, take it to a local recycling plant for a
disposal which is not harmful to the environ-
ment.
ENGLISH
*factory setting, for changing see chapter 4.3.1