Specification

ManualsBrandsMondawe ManualsBathRetro Series 3-Spray Patterns with 1.8 GPM 8 in. Rain Wall Mount Dual Shower Heads Handheld and Spout in Oil-Rub Bronze

Page 1 of 5

All testing and sample preparation for this report was performed under the continuous, direct supervision of IAPMO R&T Lab, unless otherwise stated. The statement

of compliance is based on the test results compared to the standard specifications without considering measurement uncertainty. The observations, test results and

conclusions in this report apply only to the specific samples tested and are not indicative of the quality or performance of similar or identical products. Only the Client

shown above is authorized to copy or distribute the report, and then only in its entirety. If presented with a copy of a Test Report without the IAPMO R&T Lab

watermark background, contact IAPMO R&T Lab for verification. Any use of the IAPMO R&T Lab name for the sale or advertisement of the tested material, product or

service is prohibited absent the advance written consent of IAPMO R&T Lab.

Report Number: 3343-23007

Report Issued: June 8, 2023 Project No.: 40101

Client: Mondawe INC

1942 Broadway Street, STE 314C

Boulder,CO,80302

USA

Source of Samples: The samples were sent by Manufacturer and received by IAPMO R&T Lab in

good condition on February 7, 2023.

Date of Testing: February 8, 2023 through June 8, 2023

Sample Description: shower sets

Model No.: see the page 2 for details.

Scope of Testing: The purpose of the testing was to determine if the sample tested of the various

bathtub faucets met the requirements of California Appliance Efficiency

Regulations [when tested in accordance with 10 C.F.R. Section 430.23(t)

(Appendix S to Subpart B of part 430) for maximum flow rate and Section

5.12 of ASME A112.18.1-2012/CSA B125.1-2012 for minimum flow rate]

Conclusion: The samples tested of the shower sets, model as the page 2, from Mondawe INC

COMPLIED with the requirements of California Appliance Efficiency Regulations [when tested in

accordance with 10 C.F.R. Section 430.23(t) (Appendix S to Subpart B of part 430) for maximum

flow rate and Section 5.12 of ASME A112.18.1-2012/CSA B125.1-2012 for minimum flow rate].

Tested by, Reviewed by,

Tengfei (Vincent) Xiong, Technician Xicheng Xiong, Executive Vice-GM

Summary of content (5 pages)

PAGE 1
Report Number: 3343-23007 Report Issued: June 8, 2023 Client: Mondawe INC 1942 Broadway Street, STE 314C Boulder,CO,80302 USA Source of Samples: The samples were sent by Manufacturer and received by IAPMO R&T Lab in good condition on February 7, 2023. Date of Testing: February 8, 2023 through June 8, 2023 Sample Description: shower sets Project No.: 40101 Model No.: see the page 2 for details.
PAGE 2
Model list: Item Model No.
PAGE 3
Primary Regulation: California Appliance Efficiency Regulations Test Results: All tests and evaluations were conducted per the written procedures specified in the Regulation and its reference standard. California Appliance Efficiency Regulations Section 1605.3 (h) Plumbing Fittings (5) Showerhead and handshower –COMPLIED The flow rate of the showerhead / handheld shower / body spray was not greater than 1.
PAGE 4
(d) Marking Requirements for Federally-Regulated Consumer Products – COMPLIED The product and package shall be marked with the markings required by 16 C.F.R. part 305. Finding: Marking Requirement On Product On Package Status Flow Rate in Both gpm and L/min Yes Yes PASS Manufacturer’s Name / Trademark Yes Yes PASS Model Number Not Required Yes PASS Note: According to the packaging and product drawing provided by the Manufacturer. Report No.
PAGE 5
Photograph of Samples Tested Model.: MD-A3815-BN Report No.