owners manual
Contents Introduction: 1 Attaching Feet and Spikes 2 For Carpeted Floors 2 For Wooden/ Hard Floors 2 Setting Up Your Loudspeakers 2 2 Channel Positioning 2 AV Positioning 3 Setting Up Bronze FX 3 Atmos 4 In-Ceiling 4 Bronze AMS Dolby Atmos® enabled speakers 4 Fixing Bronze FX & Bronze AMS to a Wall 4 Wiring 5 Single Wiring 5 Bi-Wiring 5 Bi-Amping 5 The Effects of Bi-Wiring and Bi-Amping 6 Port Bungs 6 Running-In Your Speakers 7 Retention Bolt Adjustment 7 Warranty 7
8 7 5 6 Attaching Feet and Spikes For Carpeted Floors D (Bronze 200 and 500 only) A The spikes and ‘out-riggers’ are supplied assembled for use on carpeted floors or where spikes are appropriate. All that is required is to fix them to the speaker base using the supplied bolts (A & B). You can check that the speaker is level on all sides by using a spirit level (not supplied). If it’s slightly off-level, unscrew the spike and check again. Continue this process until the cabinet is fully level.
AV Positioning Please refer to the illustrations below for the ideal angles and positions of each speaker in your surround system. The speakers should be distanced from the wall according to the requirements of the speaker, which are listed in the 2-Channel Positioning section. If the sound is too bass heavy or there is bass boom from the room when playing music (without a subwoofer), try moving the loudspeakers slightly further away from the wall(s).
Atmos In-Ceiling When arranging the overhead channels in an Atmos system we would recommend using our three-way in-ceiling speakers. These employ a unique pivoting midrange/ tweeter module which offers a wider dispersion characteristic, and are ideal for Atmos duties. More information can be found on our website: monitoraudio.com Please see below for ideal positioning of 2 or 4 Atmos speaker setups.
Wiring Single Wiring Single wiring is achieved via a single set of cables to the terminals on the back of the loudspeaker. Internally the loudspeaker crossover guides the frequencies to the appropriate driver/tweeter. Low frequencies to the bass drivers, mid frequencies to the mid/bass drivers and high frequencies to the tweeter. It is perfectly acceptable to connect to the top, bottom terminals or even diagonally (experimentation is advisable to achieve the preferred results).
The Effects of Bi-Wiring and Bi-Amping Fundamentally a loudspeaker crossover varies the impedance seen by the speaker and by the power amplifier. When a full range audio signal is applied to the terminals of a full range speaker system, the bass driver(s) will only receive low frequency signals, the mid driver receives the mid band frequency signals and the tweeter only gets sent high frequency signals.
Running-In Your Speakers Run your speakers in by playing music at low-mid listening levels for approximately 50-70 hours play time. You may find the sound will continue to improve even after the 70 hour mark. This can be done naturally over time: like a fine wine the performance will improve with age.
Bass reflex HiVe II port system 20 – 80 W Bass reflex HiVe II port system Recommended Amplifier Requirements N/A 7.8 kg 17 lb 3 oz 281 x 166 x 265 mm 11 1/16 x 6 9/16 x 10 7/16” N/A 5.0 kg 11 lb 0 oz Drive Unit Complement External Dimensions Including Grille and Terminals (H x W x D) External Dimensions including Outrigger Feet and Spikes (H x W x D) 12.
Monitor Audio Ltd. 24 Brook Road Rayleigh, Essex SS6 7XJ England Tel: +44 (0)1268 740580 Email: info@monitoraudio.co.uk Web: monitoraudio.com Designed & Engineered in the United Kingdom Made In China Version 1.
Loudspeaker •00 • - u r x2 Subwoofer 5mm (Exc. Centre) Quick Start Guide UK/ Euro Bronze 200 & 500 Only x8 3mm il x 8 x8 x8 c monitoraudio.
Feet (Bronze 200 & 500) (b ,, ,.._________,_1111111,------.
Loudspeaker Positioning 2 Channel Stereo Surround Sound AV rn1I] \ ---------------------1 □ IJ °\:):----------------------------{ii' xm \ \ \ I I \ I \ IJ I I \ / I \ \ \ \ I \ \ I \ \ I I \ \ I \ xm -22° \ xm -30° / 0° I 22° ~ \ I \ I \ \ \ \ 30° I I \ I \ I \ I \ I \ I \ \ A I A -----~-----[ _II/_II J-----) -----90° 90° -110° I 1 I I -90° I B 7.1 = A + B 5.1 = A / B I I I -150° ' 110° \ ' ' ' ' 150° X' 135° \ B
AV @ @ BRONZEW10 ----- it~.&. - ..~-.:.:z..-.:r-======--=-::-~-==- @)MDNlllJUllDID) -~ Volume @ 2 Channel Movie 180' On Auto Max Subwoofer Min Phase o• Mode Impact Bass ©@ AVR Sub Out @ @ @ @ BRONZEW10 ~ @ @ @) @ @ @ooNnmAUDIO) @ @ @ @ @ BRONZEW10 @ ~; § ~010) l--.
Power 14':V UW 3 Trigger 110- 12av- @ Subwoofer & Speakers Manual o o o o monitoraudio.
EN Frequency Response Sensitivity (1W@1M) Nominal Impedance Maximum SPL (Pair) Power Handling R.M.S Recommended Amp Requirements R.M.
EN Low Frequency Limit Upper Frequency Limit Amplifier Output Bass EQ Modes Input Impedance Mains Input Voltage (Factory Preset) Power Consumption Dimensions (Including grille, amp & feet) (H x W x D) Product Weight FR Limite de fréquence basse Limite de fréquence haute Sortie de l'amplificateur Modes d'égalisation de la basse Impédance en entrée Tension d'entrée principale (Préréglage d'usine) Consommation électrique Dimensions (grille, amplificateur et pied compris) (H x L x P) Poids du
MONITOR AUDI © Monitor Audio Version 2 2020 Monitor Audio Ltd 24 Brook Road Rayleigh, Essex United Kingdom SS6 7XJ +44 1268 740 580 info@monitoraudio.com monitoraudio.
€~ BRONZEFX MONITOR AUDI~ 200mm 33.75mm @ @ ---// /,,-' ,, / / / / I \ I \ I i" I _ _ _11 \ III J I Ilj!1 , I t 54mm / ' D 41mm '- e el + ( ) 41mm 62mm - - - - - - - - - 284mm - - - - - - - - -
12. This exclamation point within an equilateral triangle is intended to alert the user to the presence of important maintenance (servicing) instructions in the literature accompanying the appliance. Important Safety Instructions 1. Please read these instructions. 2. Please keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus with water. 6. Clean only with a dry cloth.
RoHS Declaration of Conformity Directive 2011 /65/EU of the European Parliament and of the Council on the reduction of the use of certain hazardous substances in electrical and electronic equipment, June 2011.
including 16 Ampere per phase). EC Declaration of Conformity EN6100-3-3: 01.95 Electro magnetic compatibility (EMC) - Part 3: Limits - Section 3 : Limits of voltage fluctuations and flicker in We, Monitor Audio Ltd. (Manufacturer and Importer) 24 Brook Road Rayleigh Essex SS6 7XJ England low-voltage supply systems for equipment with rated current up and including 16 Ampere per phase.
