Owner's Manual

31-49140-2
Installation Instructions - Standard Installation
14
STEP 1 REMOVE PACKAGING
WARNING
Tip Over Hazard. Product
is much heavier at the top than at the bottom – be
careful when moving. When using a hand truck, handle
from side only.
AVERTISSEMENT
Risque de
basculement Le produit est beaucoup plus lourd en haut
qu’en bas. Il faut être prudent lors des déplacements. Si un
diable est utilisé, il faut soulever le réfrigérateur sur le côté
seulement.
ADVERTENCIA
Riesgo de Caída El
producto es mucho más pesado en su parte superior que en
su parte inferior – tenga cuidado al moverlo. Al usar un carro
manual, sosténgalo de costado únicamente.
• Carefully cut banding at the top and bottom, remove
outer carton.
• Slide out back corner posts (2).
• Slide carton off top of cabinet.
NOTE: IT IS NOT NECESSARY TO LAY CABINET
DOWN IN ORDER TO REMOVE SKID!
NOTE: DO NOT ATTEMPT TO ROLL UNIT OFF SKID.
STEP 2 INSTALL WATER LINE
WARNING
Connect to potable water supply
only.
AVERTISSEMENT
Raccordez l’appareil à une
alimentation d’eau potable seulement.
ADVERTENCIA
Realice la conexión a un
suministro de agua potable únicamente.
• A cold water supply is required for automatic icemaker
operation. The water pressure must be between 40 and
120 p.s.i. (275-827 kPa).
• Route 1/4” OD copper or SmartConnect
™
plastic
tubing between house cold water line and the water
connection location.
• Tubing should be long enough to extend to the front of
the unit. Allow enough tubing to accommodate bend
leading into the water line connection.
NOTE: The only Monogram approved plastic tubing is
supplied in the SmartConnect
™
Refrigerator Tubing kits.
Do not use any other plastic water supply line because
the line is under pressure at all times. Other types of
plastic may crack or rupture with age and cause water
damage to your home.
SmartConnect
™
Refrigerator Tubing Kits are available in
the following lengths:
2’ (.6 m) WX08X10002 15’ (4.6 m) WX08X10015
8’ (2.4 m) WX08X10006 25’ (7.6 m) WX08X10025
• The unit is secured to the skid
with 4 slotted tie-down straps.
Remove the four 5/16” bolts
from the base channels in the
tie-downs.
• Unit is shipped with two sets
of toe kicks. One for Flush
Inset (longer) and One for
standard installation (shorter).
Pick proper toe kick for your
installation. Discard other toe
kick.
• Remove toekick, custom handle trim, and wall bracket.
Set aside for final installation.
• Lift the unit off the skid with an appliance dolly. Handle
from the sides.
• Remove the four 7/16” bolts securing the tie-down
brackets to the skid.
NOTE: Commonwealth of Massachusetts Plumbing
Codes 248CMR shall be adhered to. Saddle valves
are illegal and use is not permitted in Massachusetts.
Consult with your licensed plumber.
Shut off the main water supply.
Turn on the nearest faucet long enough to clear the line
of water.
• Install a shut-off valve between the icemaker water
valve and cold water pipe in a basement or cabinet.
The shut-off valve should be located where it will be
easily accessible.
• Turn on the main water supply and flush debris. Run
about a quart of water through the tubing into a bucket.
Shut off water supply at the shut-off valve.
NOTE: Saddle type shut-off valves are included in many
water supply kits. Before purchasing, make sure a saddle
type valve complies with your local plumbing codes.