Specifications

monogram.com
21
Advance planning for built-in custom all-refrigerators and all-freezers
The installation space
Product dimensions
696Dia10
6"
75" From Floor
to Bottom
of Electrical
Area
5"
5"
3-1/2"
5"
3-1/2"
Water Supply
Electrical Outlet
Location 2-1/2"
Note: Icemaker
Water Connection
Is At The Front
Of The Freezer
24-3/4" Total Depth
605Dia29
83-1/2"
To
84-1/2"
24-3/4"
A
*84"
Depth Including Handles:
26-1/4" Framed Models
26-3/4" Stainless Steel Models
B
Case Depth:
24-3/4"
2-1/2"
75" From
Floor to Bottom
of Electrical
Area
84-1/2" max
83-1/2" min
Finished
Opening
71-1/2" Finished Width
Electrical
5"
3-1/2"
24" Cutout
Depth
Water Supply
Wall View
696Dia12
28-1/2"
26"
6"
5"
5"
Freezer Refrigerator
A = 36", B = 35-1/2" for
semi-flush and 36" for
flush installations.
* Shipping height.
Cabinet height may be
changed to 83-1/2" or
84-1/2" using ZGC2 grille
panel kit. The ZKTR36
kits for 3/4" thick panels
provide a grille panel
support for all heights.
Electrical
A 115V, 60Hz., 15 or 20 amp power supply is required. An
individual properly grounded branch circuit or circuit breaker
is recommended. Install a properly grounded 3-prong
electrical receptacle recessed into the back wall. Electrical
must be located on rear wall as shown.
The serial plate is located inside the refrigerator/freezer below
the bottom storage drawer on the right side.
Note: GFI (ground fault interrupter) is not recommended.
Water line
The water line can enter the opening through the floor or
back wall. Route GE SmartConnect
™
kit or 1/4" O.D. copper
tubing between the cold water line and the water connection
location at the front of the freezer. The installation of an easily
accessible shut-off valve in the water line is required.
Leveling
The rear leveling wheels and front leveling legs are
limited to a maximum height adjustment of 1".
Side-by-side installations
When installing an all-refrigerator and all-freezer side by side,
the installation space must be 71-1/2" wide.
• Locate water and electrical as shown.
• A separate 115V, 60Hz., 15 or 20 amp power supply
is recommended for each product.
Door swing clearances
The installation must allow for clearances to adjacent walls or
cabinets. These refrigerators are factory set for a 130° door
swing. The door swing can be reduced to as little as a 90°
opening with an optional WX14X99 kit.
90° door swing with optional WX14X99 door stop.
• Allow 25" minimum clearance for a full 130° door swing.
Allow 15" for pan removal.
• 4" minimum clearance is required when the door swing is
adjusted to 90°. If the 90° door stop position is used, pan
access is maintained, but pan removal is restricted.
Clearances for multiple installations
When installing an all-refrigerator and all-freezer side by side,
allow 25" for a full 130° door swing, or 15" min. on the hinge
sides for pan removal.
605Dia34
25"
Min. to
Wall
0"
25"
Min. to
Wall
130° Door Swing 130° Door Swing
605Dia20
25"
Min. to
Wall
130°
130° Door Swing
36-3/4"
605Dia32
4" Min.
to Wall
90° Door Swing
Bu ilt- in sid e -by -s ide
re fri ger ato rs
Bu ilt- in bot to m- fre e zer
re fri ger ato rs
Bu ilt- in all -r ef rig era tor s
and a ll- fre e zer s
Free -standing side-by-side
refrigerators