Specifications

30
A
Minimum to Wall
110°
110° Door
Swing
21-5/8"
23-5/8"
B
Minimum to Wall
90°
90° Door
Swing
Location requirements
All Monogram
®
refrigeration modules may be closed in on
the top and sides as long as the front is unobstructed for air
circulation and door swing.
• Do not install these products where the temperatures will
go below 55°F (13°C) or above 90°F (32°C).
• Do not install where they will be subject to direct
sunlight, heat or moisture.
• These products are not designed to be stacked one over
the other.
Electrical
A 120V, 60HZ., 15 or 20 amp power supply is required. An
individual properly grounded branch circuit or circuit breaker
is recommended. Install a properly grounded 3-prong electrical
receptacle recessed into the back wall of the installation
location. See cutout illustration.
Note: GFCI (ground fault circuit interrupter) is not recommended.
Water line
Bar refrigerators are equipped with an automatic icemaker.
The water line can enter an opening in the back wall or floor
as shown in the cutout illustration. Route GE SmartConnect
™
kit or 1/4" O.D. copper tubing between the cold water line and
the water connection location. The installation of an easily
accessible shut-off valve in the water line is required.
Side-by-side installation
Make the most of your kitchen space with two Monogram
refrigeration modules installed together.
• Products must operate from separate properly
grounded receptacles.
Door swing clearances
All Monogram refrigeration modules are factory set for a 110°
door swing.
When installed in a corner:
• Allow the minimum door swing clearances shown. The use of
a custom panel and custom handle influences the minimum
clearances required.
• The minimum clearance shown at 90° will allow full extension
of drawers and shelves.
3/4" custom panels for fresh-food refrigerator
and bar refrigerator with icemaker
A field-installed overlay door panel is required for models
ZIFI240 and ZIBI240 refrigerators.
• The overlay panel must be secured to a 1/4"-thick backer
panel that slides into the door trim. A .10"-thick spacer panel
must be placed between the overlay and backer panel.
• Custom handles of your choice must be installed onto the
assembled overlay panel.
• ZTBSS1 Monogram stainless steel tubular handle is available
for models ZIFI240 and ZIBI240.
3/4" overlay panel dimensions (in inches)
A (width) B (height)
1/4" backer 23-3/16" 29-9/16"
0.10" spacer 22-1/2" 29-1/16"
3/4" overlay 23-5/8" 30"
Assemble overlay panels with glue and screws.
• Center spacer panel on the backer panel, left to right, and top
to bottom. Secure the panels with glue.
• Center the spacer/backer panel on the overlay panel. Secure
with glue and screws. Countersink all screws.
Custom panel hinge routing
Use a 3/4" router bit to cut a notch into the back side of the
assembled panel for hinge clearance. Cut the notch 3/4" deep,
7/8" wide and 3/8" forward of the back side.
Models A B
ZIFS240 / ZIBS240 14" 4"
ZIFI240 / ZIBI240 16" 4-1/2"
Advance planning for fresh-food refrigerator
and bar refrigerator with icemaker
Overlay
Panel
1/4"
Backer
Panel
Door
3/4" custom panels for
fresh food and bar refrigerator
3/4" custom panels for
double drawer refrigerator
.10 Inch
Spacer
B
A
1/4" Gap
12-1/2 lbs. max.
B
12-1/2 lbs. max.
3/8
3/4
Right
side
view
of
overlay
custom
panel
Route
for hinge
clearance
Front
7/8
3/8
Top
view
of
overlay
custom
panel
Route
for hinge
clearance
Front
A
B
Spacer Panel
Backer Panel
Overlay Panel
Overlay
Panel
1/4"
Backer
Panel
Door
.10 Inch
Spacer
Spacer Panel
Backer Panel
Overlay Panel
Overlay
Panel
1/4"
Backer
Panel
Door
3/4" custom panels for
fresh food and bar refrigerator
3/4" custom panels for
double drawer refrigerator
.10 Inch
Spacer
B
A
1/4" Gap
12-1/2 lbs. max.
B
12-1/2 lbs. max.
3/8
3/4
Right
side
view
of
overlay
custom
panel
Route
for hinge
clearance
Front
7/8
3/8
Top
view
of
overlay
custom
panel
Route
for hinge
clearance
Front
A
B
Spacer Panel
Backer Panel
Overlay Panel
Overlay
Panel
1/4"
Backer
Panel
Door
.10 Inch
Spacer
Spacer Panel
Backer Panel
Overlay Panel
The serial plate is located on the inside ceiling of the fresh-food
refrigerators, and on the left wall below the ice compartment of
the bar refrigerators.
Right-hand door
swing shown.
Allow the same
clearances
for left-hand
models on the
opposite side.
Maximum
assembled
panel weight
is 25 lbs.
Note: Right-hand
models illustrated.
Cut notches on the
opposite side for
left-hand door swing.