Specifications

62
Advance planning for chimney hoods—wall-mount
Wall-mount hoods
Chimney vent hoods are available in a 36" width. All models
are supplied with a two-piece stainless steel duct cover to
conceal the ductwork running from the top of the hood to
the ceiling.
• The installation height should be determined in advance.
If necessary, accessories for height adjustment should be
ordered with the vent hood and be on-site at the time of
installation.
• Review the following chart to determine the need for an
accessory duct cover.
Duct cover accessories for vented installations
Ceiling height ZV750 ZV950 ZV800 ZV900
8 ft. Included Included Included up to 9'5"
Up to 9 ft. Included Included Included up to 9'5"
Up to 10 ft. ZX10SY Included Included ZX90010*
10 ft. to 14 ft. — ZX14SDSS — —
*ZX90010 for 9'6" up to 10'5"
Structural suppor t
These vent hoods are heavy. Adequate structural support
must be provided. Hoods must be secured to vertical studs
in the wall or to horizontal supports.
• It is strongly recommended that the vent hood and duct
cover(s) if used, be on-site before final framing and wall
finishing. This will help to accurately locate the ductwork
and electrical service.
• Final installation will be much easier if the hood is installed
before the range or cooktop below.
• Mounting templates are provided with the installation
instructions to help accurately position the hood above the
cooking surface.
Electrical requirements
These vent hoods must be supplied with 120V, 60Hz, and
connected to an individual, properly grounded branch circuit
protected by a 15 or 20 amp circuit breaker or time delay fuse.
Duc twork planning
• Plan the shortest and straightest route for venting exhaust
to the outdoors.
• Use metal ductwork only
• Install a wall cap or roof cap with damper at the exterior
opening. Order the wall or roof cap and any transition
needed in advance.
Duc twork for ZV750SY
This vent hood must use 6" round duct with a maximum
equivalent length of 100 feet for any duct configuration.
Refer to the duct fittings chart in the installation
instructions.
Decorative duct covers
This vent hood is supplied with a two-piece decorative duct
cover that will reach an 8-ft. to 9-ft. ceiling. ZX10SY can be
ordered to reach 9-ft. to 10-ft. ceiling heights.
Recirculating installation for ZV750
The ZV750 hood is designed to be vented to the outside,
but can easily be converted for recirculating operation.
Recirculating kits are available for
this hood. These kits include charcoal
filters, an air deflector that fits over the
exhaust outlet and a vented decorative
duct cover. Kits are sized for ceiling height.
Recirculating installations
Up to 9 ft. ceiling ZXR758C
Up to 10 ft. ceiling ZXR7510C
Duc twork for ZV800SJSS, ZV800BJBB
This vent hood must use 6" round duct with a maximum
equivalent length of 100 feet for any duct configuration.
Refer to the duct fittings chart in the installation
instructions.
Decorative duct covers
This vent hood is supplied with a two-piece decorative duct
cover that will reach an 8-ft. to 10-ft. ceiling. The duct covers
are reversible for recirculating operation.
Duc twork for ZV90 0SL SS
This vent hood must use 8" round duct with a maximum
equivalent length of 100 feet for any duct configuration. Refer
to the duct fittings chart in the installation instructions.
Decorative duct covers
This vent hood is supplied with a two-piece decorative duct
cover to reach an 8-ft. to 9'5" ceiling. ZX90010 can be ordered
to reach 9'6" to 10'5" ceiling heights. All duct covers are
reversible for recirculating operation.
Duc twork for ZV950SDSS
This vent hood must use 8" round duct with a maximum
equivalent length of 100 feet for any duct configuration.
Decorative duct covers
This vent hood is supplied with a two-piece decorative duct
cover that will reach an 8-ft. to 10-ft. ceiling. An optional
accessory, ZX14SDSS, can be ordered to reach 10-ft. to 14-ft.
ceiling heights. For vented operation only.
605Dia145