Specifications

84
Advance planning for telescopic downdraft vents
Electrical and gas locations
Plan the placement of the electrical
outlet and gas (if used) carefully. Gas
or electrical outlets cannot be located
on the back wall of the cabinet
because they may interfere with the
downdraft plenum.
• Install a standard electrical outlet within
reach of the vent’s two-foot-long power cord.
Locate the outlet inside the cabinet on the
right side wall.
• If the vent is installed in combination with a
Monogram gas cooktop, it may operate from
the same 120V standard duplex outlet.
• If the vent is installed in combination with a
Monogram electric cooktop, the vent must
operate from a separate 120V outlet.
Cutouts and clearances
Identify the cutout illustration for the Monogram
®
cooktop model you are installing.
34" for 36" Models
28-1/2" for 30" Models
29-1/2"
Electrical
Outlet
12" Above
Cabinet Floor
Do Not Locate Gas or Electrical
Connections Within Shaded Area
682Dia47
ZGU36K gas cooktops with 36" vent
Cabinet: Requires
22-11/16" inside
cabinet depth.
Remove rear
support rail.
2-1/2" Min.
Clearance to Cutout
34" Cooktop and Vent Cutout
13/16" Cooktop Overlap
(1-1/2" at Center)
Front Edge
of Countertop
21-3/4"
Cutout
Depth
1/4" Overlap
23-1/2" (SS)
23-3/8" (B,W)
Total Flat
Surface
Required
at Center
1/8" Gap
605Dia170
36"
2-1/4" Min. Cooktop Cutout to Rear
Vertical Combustible Surface
6" Min. Cutout
to Side Walls
605Dia171
3/4"
22-3/4" to Back Wall
22" to Support Rail
24-3/4"
2-1/2" to
Cutout
ZGU36 Cooktop
1-7/8"
3/4"
Thick
Support
Rail
20-1/16"
DOWNDRAFT VENT
Countertop cutout: Requires
23-3/8" (B,W) 23-1/2" (SS) flat
countertop surface. Requires
24-3/8" (B,W) and 24-1/2" (SS)
total countertop depth.
ZGU384 gas cooktops with 30" vent
Cabinet:
Requires 23" inside
cabinet depth. See
Creative Solutions,
install in an island or
move cabinet base
forward.
28-1/2" cooktop
and vent cutout
7/16" cooktop overlap
(1-1/4" at center)
Front edge
of countertop
2-1/2" min. clearance
to cutout
12" min. cutout to
wall, both sides
30-3/4"
2-3/4"
22-3/8"
cutout
depth
23-7/8"
total flat
surface
required
at center
2-7/8" min.
cooktop
cutout to
rear verticle
combustible
surface
1/8"
gap
19-5/8"
cooktop
cutout
depth
3/8" 3/8"
zgu384_in_cabinet
3/4"
22-3/4" to Back Wall
22" to Support Rail
24-3/4"
2-1/2" to
Cutout
ZGU384 Cooktop
1-7/8"
3/4"
Thick
Support
Rail
20-3/8"
DOWNDRAFT VENT
Countertop cutout: Requires
23-7/8" flat countertop surface and
24-7/8" total countertop depth.
ZGU385 gas cooktops with 36" vent
Cabinet: Requires
22-11/16" inside
cabinet depth.
Remove rear
support rail.
2-1/2" Min.
Clearance to Cutout
34" Cooktop and Vent Cutout
7/16" Cooktop Overlap
(1-1/4" at Center)
Front Edge
of Countertop
21-11/16"
Cutout
Depth
1/4" Overlap
23-5/16"
Total Flat
Surface
Required
at Center
1/8" Gap
605Dia170
36-3/4"
3/8" 3/8"
3-3/8" Min. Cooktop Cutout to Rear
Vertical Combustible Surface
12" Min. Cutout
to Side Walls
zgu385_in_cabinet
1"
22-3/4" to Back Wall
22" to Support Rail
24-3/4"
2-1/2" to
Cutout
ZGU385 Cooktop
1-7/8"
3/4"
Thick
Support
Rail
20-1/16"
DOWNDRAFT VENT
Countertop cutout: Requires
23-5/16" flat countertop surface
and 24-1/2" total countertop depth.