Owner’s Guide and Installation Manual 6LFR62XXXD Series Fan cETL Model NO. : 6LFR62 Attach sales receipt to this card and retain as your proof of purchase DATE OF PURCHASE: RETAILER NAME: MODEL NUMBER: RETAILER ADDRESS: To register your fixture, please visit our website www.montecarlofans.com 9.94 kg 21.
Cautions and Warnings WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING READ AND SAVE THESE INSTRUCTIONS Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA 70), including fire-rated construction. Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.
1 2 ON 3 ON Mounting bracket OFF OFF Before you begin installing the fan, Switch power off at Service panel and lock service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the service panel. Use AC 120V/60HZ power supply only. 4 Before installing this fan make sure the outlet box is properly installed to the house structure.
7 8 9 Downrod Yoke Canopy Canopy bottom cap Yoke cover Place downrod over canopy, canopy bottom cap and yoke cover 10 Partially loosen downrod set screws from yoke at top of motor assembly. 11 Thread lead wires and safety cable from motor assembly through downrod. 12 Tab Cross pin Screwdriver Slot Keeper pin Downrod Cross pin Helpful hint: For easy assembling of the cross pin on the next installation step.
SAFETY CABLE INSTALLATION 13 14 Wall Switch Black (Live) Power source White (Neutral) Blue (For Light) Ground/Green White (For Light) Red (Motor 1) Purple (Motor 2) Lag screw Safety cable Gray (Motor 3) Green/Ground Washer Lock washer For Canadian installation and for USA fan and light kit combinations over 35 lbs, in both flush and downrod modes the safety cable must be installed into the house structure beams using 1.5” lag screws, washers and lock washers provided.
18 19 20 Plate on motor Light pan Loosen 2 and remove one set screws from the plate on motor as shown in illustration. Keep screw. Place light pan over lead wires 21 22 Install LED Light Kit Install the light pan. Align its key holes with the set screws on the plate and reinstall the screw removed in step 18. Tighten screws securely. 23 LED light fixture Removed set screws from light pan. Keep screws.
24 25 26 Install Blanking Plate Lexan shade Attach LED light fixture onto the light pan, aligning the holes on the LED light fixture with the screw holes on light pan. Reinstall the screws removed in step 21. Tighten all screws securely. © 2021 Monte Carlo Fan Collections Attach lexan shade by locating dimples in light pan with grooves on the Lexan shade and twist clockwise until tight. 7 Isolate the quick connects with electrical tape.
REMOTE CONTROL SETTING and OPERATION Transmitter Operation Remove the battery cover from the remote control transmitter and install battery, battery provided. Replace the cover. Note: Use 2 1.5V/AAA battery. Note: If not using for long period of time, remove battery to prevent damage to remote transmitter, and store the remote transmitter away from excess heat or humidity.
The buttons on the remote control transmitter control the fan speed and light as follows. Fan speed 1 = minimum speed 3 = medium low speed 5 = medium high speed 2 = low speed 4 = medium speed 6 = high speed This button turns the fan off. Forward/Reverse button- This button is to control direction of fan rotation. Press once to change direction of the fan rotation. Fan must be running to reverse. Light button- Press this button to turn light on or off.
Trouble Shooting or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults, installation, please call our Customer Service Center at the number printed on your parts list insert sheet. Warning means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel. Trouble 1. If fan does not start: Suggested Remedy 1.
Jan.