Stereo micro hi-fi system with cd player 29107 OPERATING INSTRUCTIONS
Illustration 19 1 3 5 11 2 4 8 6 17 12 13 10 9 7 18 16 15 14 20 2
Display illustration Remote control 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 1 2 3 4 5 6 7 8 Head phone jack IR (infra red) sensor Prog/clk-adj button Stop button Cd mode button Tuning control Skip / search down button Play / pause button Skip / search up button Power / standby indicator button LCD display window Cd / radio switch Volume (up / down) button MW / FM - FM ST.
Cd display A B C D E F G Stereo indicator Program indicator Random indicator Repeat indicator Track number indicator Mute indicator Play/pause indicator A G D C B REPEAT RANDOM PROGRAM FM MW AM PM ST .. . F MHz KHz E Putting the batteries into the remote control unit 1 2 3 Press down the compartment cover, and slide the cover off and open the compartment.
Electrical requirements Check the voltage on the rating plate of your CD microsystem corresponds with your house electricity supply which must be A.C. (alternating current). If the socket outlets in your home are not suitable for the plug supplied with this appliance the plug should be removed and the appropriate one fitted. WARNING: The plug if severed from the mains lead must be destroyed as a plug with a bared flexible cord is hazardous if engaged into a live socket outlet.
4 5 Press the PROGRAM/CLK-ADJ button again, the LCD display shows the minute digit flash, then press the skip/search (up or down) button to adjust the minute digit. Last press the PROGRAM/CLK-ADJ button to validate the clock. Radio operation 1 Set the CD / RADIO switch to the radio position. FM 2 Select FM mode with the BAND switch. 3 Turn the TUNING control to select the required station. 4 Fully extend the FM aerial and adjust its direction for best FM reception MW 2 Select MW on the BAND switch.
FM aerial FM wire aerial To obtain the maximum FM reception fully extend the wire FM aerial (which is located at the rear of the unit) and alter the direction of the wire for best results. Listening to the compact disc (cd) The LCD indicator will always show the tracks of a disc or program which are still to be played. In stop mode all tracks on the disc will be displayed. Playing back the entire disc 1 Playback will start by pressing PLAY/PAUSE, the indicator then appears.
Programmed playback Upto 20 tracks can be programmed for playback. 1 Press the PROGRAM/CLK-ADJ button when the cd has been stopped. 2 Select the desired track number using the SKIP/SEARCH button on the unit or the remote control. 3 Press the PROG button to select the track. 4 Repeat steps 1 and 3 depending on how many tracks are to be programmed (upto a maximum of 20). 5 Press the PLAY/PAUSE button to start playing the first of the selected tracks. 6 To stop playing, press the STOP button.
Compact disc 1 2 3 4 Always use compact discs bearing the mark as shown. Notes on handling discs: When removing the disc from its storage case and loading it. * Do not touch the reflective recorded surface. * Do not stick paper or write anything on the surface. * Do not bend the disc. Storage: * Store the disc in its case. * Do not expose discs to direct sunlight or high temperatures, high humidity or dusty places.
Listen to music on headphones A stereo headphone jack is provided for private listening. To listen using headphones (NOT INCLUDED) insert the 3.5mm mini-stereo plug from the headphones into the phones jack on the front panel. The external speakers are automatically disconnected when headphones are in use. Warning labels WARNING: to reduce the risk of an electric shock, do not expose this appliance to rain or moisture. ATTENTION: To reduce the risk of an electric shock, do not remove the cover.
Technical specification AC power supply AC power consumption : : 230V 30W 50Hz Remote control unit : 3V (AA size/UM3/ x 2) Batteries not included Speaker Speaker capacity power Amplifier max power : : : 3 inch woofer + 1.5 inch x 2 tweeter 10W x 2 (4 Ohm) 2 x 2W Radio : : FM 87.5MHz - 108MHz MW 540KHz - 1600KHz Compact disc Frequency response : : 3 - Beam laser 100Hz - 16kHz WARNING : This unit uses a laser beam.
Guarantee Morphy Richards products are manufactured to internationally accepted quality standards. In addition to your statutory rights, Morphy Richards guarantee your product to be free from manufacturing and component defects for a period of TWO YEARS from date of purchase. If your product proves to be defective within 28 days of purchase, your Morphy Richards dealer from whom the product was purchased will be pleased to replace it free of charge.